Loading ...
Loading ...
Loading ...
OPERATION INSTRUCTIONS
BEFORE USING YOUR APPLIANCE
• Remove the exterior and interior packing
• Before connecng the appliance to the power source, let it stand upright for approximately 4 hours. This will reduce the possi-
bility of a malfuncon in the cooling system from handling during transportaon
SWITCHING ON/OFF THE AIR CONDITIONER
The appliance can be switched ON or OFF by pressing the POWER button on the control panel or the ON/OFF button on the remote
control
COOLING MODE
In this mode, the air condioner cools and dehumidies the room. To acvate this funcon mode, press the MODE
buon unl the COOL indicator light comes on. When the cooling mode is set, the compressor will start in approximately 3
minutes. In cooling mode, hot air is exhausted from the outdoor exhaust port and the exhaust hose must be connected to exhaust
out the hot air. The temperature seng range of this air condioner is from 60°F / 16°C to 86°F / 30°C. To set the temperature,
press the + or - buons. This air condioner has a 5°F temperature cushion which if the set temperature is within 5°F of the ambi-
ent temperature, the unit runs on fan only mode. This saves energy and prolongs the life of the compressor of the air condioner.
To set the fan speed, press the FAN buon. In cooling mode, the dierence in noise level between the fan speeds is not very no-
ceable when the compressor is on. Try seng the unit to Fan only mode, you should be able to hear the dierence between high
and low fan speed sengs.
DRY (DEHUMIDIFYING) ONLY MODE
In this mode, the air condioner only dehumidies the room, the compressor will acvate intermiently depending on the ambient
temperature and the fan speed is set to LOW. To acvate this funcon mode, press the MODE buon unl the DRY indicator light
is displayed. Please note that when switching funcon mode, there will be an approximately 3 minute transion me. In dehumidi-
fying mode, the exhaust hose does not need to be vented. If the exhaust hose is vented, the room will be cooled as it dehumid ies.
To prevent cooling, remove the exhaust hose from the window kit and allow the warm air from the rear to be re-circulated into the
room. If room temperature is higher than 77°F, the fan speed can be adjusted. If room temperature is lower than 77°F, the fan
speed is set at Low.
NOTE: When using dehumidifying mode, venng the exhaust hose to the outside is not required. If vented, the warm air is exhaust-
ed to the outside and cooling within the room may occur. Addionally, if the exhaust hose is not vented, the unit may require more
frequent draining. Also, the air condioner does not have a humidistat in which a specic humidity level can be set.
AUTOMATIC MODE
When you set the air condioner in AUTO mode, it will automacally select cooling or fan only operaon depending on what
temperature you have selected and the room temperature is close to the unit. The fan speed is automacally selected and cannot
be changed .To operate the unit in Auto mode when the unit is on, press the MODE button until the AUTO indicator light comes on.
HEAT MODE (*only for ARC-1230WNH)
This air condioner operates on the heat-pump principle, absorbing heat from air outdoors and transferring that heat to the indoor
unit. In this mode, the air condioner heats the room. To acvate this funcon mode, press the MODE buon unl the HEAT indi-
cator display comes on. When the heang mode is set, the compressor will start in approximately 3-5 minutes. The heang tem-
perature seng range of this air condioner is from 60°F - 86°F / 16°C - 30°C . To set the temperature, press the UP and DOWN
buons. To set the fan speed, press the FAN buon.
FAN ONLY MODE
In this mode, only the fan of the air condioner runs and circulates the air in the room. To acvate this funcon mode, press the
MODE buon unl the FAN indicator light comes on. In this funcon mode, the temperature cannot be set. Subsequently, set the
desired fan speed by pressing the FAN buon. When using FAN only mode, venng the exhaust hose to the outside is oponal.
Page 13
Loading ...
Loading ...
Loading ...