User Manual Greenworks 2531502 Pro 60V 25" Brushless Self-Propelled Lawn Mower

Greenworks 2531502 Pro 60V 25" Brushless Self-Propelled Lawn Mower - Use Manual - Use Guide PDF.
Documents: Go to download!

• Owner's manual - (English)

Table of contents

• INSTALLATION
• MAINTENANCE
• TROUBLESHOOTING

User manual Lawn Mower

INSTALLATION

UNPACK THE MACHINE

1. Open the package.

2. Read the documentation in the box.

3. Remove all the unassembled parts from the box.

4. Remove the machine from the box.

5. Discard the box and package in compliance with local regulations.

PLACE THE MOWER UPRIGHT IN VERTICAL POSITION

1. Place the mower upright in vertical position.
2. Remove the packing material from the cable.
3. Remove the rubber edge guard (G) from the upper handle.
4. Insert the upper handle (4) into the lower handle (5).
5. Put the bolts (13) through the holes and tighten with the nuts (14), using a Philips head screwdriver (not included).

UNFOLD AND ADJUST THE HANDLES

1. Pull up on the handle holes (26) to release the handles.
2. Fold the handles up until the handle pins (12) lock into position.

INSTALL THE GRASS CATCHER

1. Remove the mulch plug.
2. Open the rear discharge door (6) and hold it.
3. Hold the the grass catcher by its handle and engage the hooks on the slots (15).
4. Close the rear discharge door.

INSTALL THE MULCH PLUG

1. Remove the grass catcher.
2. Open the rear discharge door (6) and hold it.
3. Hold the mulch plug (10) by its handle and fit it in the discharge chute.
4. Close the rear discharge door.

SET THE CUTTING HEIGHT

The machine can be set to different cutting heights.

1. Pull the height adjustment lever (8) rearward to increase the cutting height.
2. Pull the height adjustment lever forward to decrease the cutting height.

INSTALL THE BATTERY PACK

1. Open the battery door (6).
2. Align the ribs on the battery pack with the grooves in the battery compartment.
3. Push the battery pack (17) into the battery compartment until the battery pack locks into place.
4. When you hear a click, the battery pack is installed.
5. Close the battery door.

REMOVE THE BATTERY PACK

1. Remove the safety key (16).
2. Open the battery door.
3. Push and hold the battery release button (18).
4. Remove the battery pack from the machine.

OPERATION

START THE MACHINE

1. Make sure safety key is inserted into slot.
2. Push and hold the start button (1).
3. While you hold the start button (1), grab the start handles (2) in the direction of the handle bar.
4. Once the machine has started, you can release the start button (1).
5. Press the Turbo button (26) to speed up to 4,500 RPM.

Battery capacity indicator (28)

STOP THE MACHINE

1. Release the start handle to stop the machine.

OPERATE THE SELF-PROPEL DRIVE SYSTEM

1. Start the machine.

2. While you hold the start handles (2), grab either of the drive levers (3) and pull towards the handle bar.

3. Hold the start handles and the drive levers at the same time.

4. Release either set of start handle and drive lever from the same side.

5. Adjust the speed control (27) with your free hand.

• Slide the speed control button in the direction of the Rabbit Symbol to increase the speed.
• Pull the speed control button in the direction of the Turtle Symbol to decrease the speed.

6. Release the drive levers to close the self-propel system.

To engage the self-propel drive system while the mower is not running:

• Press and hold the start button (1), then pull up on the drive lever (3).

OR

• Pull up on the drive lever (3), then press the start button (1).

LED HEADLIGHT

1. When the mower is ready to start, you may grab the start handle (2) or the self-propel lever (3) to turn on the LED headlight (11).
2. Release the start handles and self-propel levers to turn off the headlight.

EMPTY THE GRASS CATCHER

1. Stop the machine.
2. Remove the safety key.
3. Remove the battery pack.
4. Open the rear discharge door and hold it.
5. Hold the grass catcher by its handle and unhook it from the slots.
6. Close the rear discharge door.
7. Empty the grass catcher.

OPERATE ON SLOPES

• Do not go up and down on a slope, mow across the face of the slope. Be careful when you change the direction on a slope.
• Monitor the holes, ruts, rocks, and other hidden objects that can cause you to fall. Remove all obstacles such as rocks and tree limbs.
• Make sure that your footing is stable. If you are out of balance, release the start handle immediately.
• Do not mow near drop-offs, ditches, or embankments.

OPERATION TIPS

• Do not try to override the operation of the start button or start handles.
• Do not tilt the machine when you start it.
• Do not put hands or feet near or below the turning parts.
• Keep the discharge chute clean.
• Do not cut wet grass.
• Higher blade height is necessary for new or thick grass.
• Clean the bottom of the mower deck after each use. Remove grass clippings, leaves, dirt, and other debris.

MAINTENANCE

GENERAL MAINTENANCE

• Before each use, examine the machine for damaged, missing, or loose parts such as screws, nuts, bolts and caps.
• Tighten correctly all the fasteners and caps.
• Clean the machine with a dry cloth. Do not use water.

REPLACE THE BLADE

1. Stop the machine.

2. Make sure that the blades fully stop.

3. Remove the safety key and battery pack.

4. Turn the machine to its side.

5. Use a piece of wood to prevent the movement of the blade.

6. Remove blades with a wrench or a socket:

• Turn nut (24) to the right to remove blade A (20), spacer (25) and positioner (22);
• Turn nut (24) to the left to remove blade B (21), spacer (25) and positioner (23).

7. Install the new blade. Position the blade with the cutting edges toward the ground. Make sure the two posts on positioner engage the holes on the blades.

8. Assemble the positioners and spacers as shown.

Positioner (22) for blade A only; positioner (23) for blade B only. Mounting nuts and spacers of blade A are interchangable with that of blade B.

HIGH LIFT BLADES

This mower comes with an extra set of high lift blades. Normal stock mower blades perform well on dry, shorter grasses, and are optimized for efficiency, while high lift blades work better in extreme conditions. The high-lift blade has deeper curves on the ends, which increase suction to circulate and expel the clippings. The higher air flow also helps prevent clogging when mowing tall or wet grass.

VERTICAL STORAGE

1. Remove the grass catcher.
2. Remove the battery and safety key.
3. Pull through the handle holes to fold away the handles.
4. Lock the handles into position.
5. Stand the machine on end and make sure that the brackets touch the floor.

STORE THE MACHINE

• Clean the machine before storage.
• Make sure the motor is not hot when you store the machine.
• Make sure that the machine does not have loose or damaged parts. If it is necessary, do these steps/ instructions:
• Replace the damaged parts.
• Tighten the bolts.
• Speak to a person at an approved service center.
• Store the machine in a dry area.
• Make sure that children cannot come near the machine.

TROUBLESHOOTING

See other models: 25142 25223 25322 2502402TNVAZ 2501202