User Manual Dirt Devil UD20121 Endura Lite Upright Vacuum

• Owner's manual - (English, French, Spanish)

Table of contents

• FEATURES
• HOW TO ASSEMBLE
• HOW TO OPERATE
• DIRT CUP & FILTER: REMOVAL & REPLACEMENT
• BELT OR BRUSHROLL: REMOVAL & REPLACEMENT
• HOSE AND TOOL USAGE
• TROUBLESHOOTING GUIDE
• LIMITED WARRANTY

FEATURES

1. Handle Grip
2. Stretch Hose
3. Dust Brush*
4. Tool Caddy*
5. Dirt Cup Release Button
6. Baffle
7. Dirt Cup
8. Filter
9. Nozzle
10. Bumper
11. Performance Indicator
12. Crevice Tool*
13. Hose Clip
14. Quick Release Cord Hook
15. Power Cord
16. Lower Hose Connector
17. Lower Cord Wrap
18. Wheels
19. On/Off Pedal
*On select models only

HOW TO ASSEMBLE

TOOL REQUIRED: PHILLIPS OR FLAT HEAD SCREWDRIVER

ATTACH FIXED HANDLE

Remove dirt cup from body of cleaner

Slide handle into hole on top of cleaner

Insert screw through hole (located under tool caddy) on back of cleaner (Diagram 3). Place bolt onto end of screw coming through back panel and tighten to secure handle (Diagram 3a).

ATTACH TELESCOPIC HANDLE

Insert handle into body of cleaner

Push down firmly until handle locks into place

FOR STORAGE

For storage, press the telescopic handle release button on the back of the cleaner and push handle down

FOR REGULAR USE

For regular use, push the telescopic handle release button and pull handle up

SECURE BACK HOSE

Wrap hose around back of hose caddy. Push hose wand down into the right side of cleaner.

TOOL STORAGE

Attach crevice tool and dust brush to tool caddy

INSTALL DIRT CUP

Replace dirt cup by tilting back until it snaps into place

HOW TO OPERATE

CORD RELEASE

Turn quick cord release for easy cord removal. To Use: Plug into electrical outlet. For convenient storage: Wrap cord on cord hooks. Attach the plug end to the cord.

ON/OFF PEDAL

Plug cord into electrical outlet. Turn cleaner on by depressing foot pedal located on the back left side of the cleaner

HANDLE RELEASE

Pull back handle to tilt back. Press on the front of nozzle if needed.

FLOOR/CARPET CLEANING

Move the handle and adjust it to the desired position for (A) operating the cleaner, and (B) lowering handle to clean under furniture.

CARRY HANDLE

Use the carry handle to move the cleaner from room to room.

DIRT CUP & FILTER: REMOVAL & REPLACEMENT

EMPTY DIRT CUP

Lift dirt cup release button on top of dirt cup to remove dirt cup.

Hold dirt cup over garbage can and press clean release dirt cup button to empty. Make sure container bottom center opening is clear of debris. Snap dirt cup bottom back into place after emptying.

REMOVE FILTER CARTRIDGE

Click the button on the base of the cleaner toward the outside edges to unlock the filter cartridge, then put away the filter cover.

Lift the filter cartridge out of the base cleaner.

REMOVE FOAM FILTER

Remove the foam filter from the filter cartridge.

CLEAN PLEATED FILTER

Tap the pleated filter on the inside of a garbage bin to remove excess dust and dirt from the filter. Replace the filter every 6 months.

RINSE PLEATED FILTER

Hold the pleated filter upside down under running water to rinse. Allow filter to dry for at least 24 hours before replacing in filter cartridge.

RINSE FOAM FILTER

Hold the foam filter under running water to rinse. Allow filter to dry for at least 24 hours before replacing in filter cartridge

REPLACE FOAM FILTER

Return foam filter to filter cartridge.

REPLACE THE FILTER CARTRIDGE

Return filter cartridge to base of cleaner.

Click button back into place to lock filter cartridge in base of cleaner.

CLEAN THE AIR DIRECTOR

To remove Air Director, rotate 1/4 turn counter clockwise.

Pull out and wipe with a damp cloth to clean

Dry and return the Air Director to the dirt cup. Rotate 1/4 turn clockwise to lock in place.

REPLACE DIRT CUP

Return dirt cup to cleaner

REGULAR MAINTENANCE: Each time the dirt cup is emptied, the filter should be cleaned. Tap the filter firmly against the inside of a trash can until the dirt stops falling from the filter. (Filter will be discolored after use, this will not affect the filter’s performance.) Do not brush the filter. The cleaning instructions may vary depending on the dirt conditions. In some cases, more or less cleaning of the filter may be required.

An internal thermal protector has been designed into your cleaner to protect it from overheating. When the thermal protector activates the cleaner will stop running. If this happens proceed as follows:

1. Turn cleaner OFF and disconnect it from the electrical outlet.

2. Empty dirt cup.

3. Inspect the nozzle and bag inlet openings for any obstructions. Clear obstructions if present.

4. When cleaner is unplugged and motor cools for 30 minutes, the thermal protector will deactivate and cleaning may continue.

If the thermal protector continues to activate after following the above steps, your cleaner may need servicing.

BELT OR BRUSHROLL: REMOVAL & REPLACEMENT

TO REMOVE BELT

Lay the cleaner flat and flip it to expose the nozzle base. The base should lay flat and face up. Remove the five (5) screws.

Pull and lift the nozzle guard off.

Lift and remove the brushroll. Dispose of the old belt.

TO REPLACE BELT OR BRUSHROLL

Slide belt onto motorshaft

Place new belt in area of brushroll without bristles.

With new belt in place, pull and slide brushroll into nozzle making sure that the brushroll end caps are in the correct orientation (6a inset). Rotate brushroll manually to make sure belt is properly aligned.

Reattach nozzle guard.

Secure by aligning the three (3) tabs in the base slots

Replace all five (5) screws to secure nozzle guard.

HOSE AND TOOL USAGE

TO USE HOSE AND ATTACHMENTS

Remove the hose from hose caddy

Choose any of the handy accessories or use the hose alone.

Simply push the attachment firmly onto the hose end. To remove tool, twist and pull apart gently

TROUBLESHOOTING GUIDE

LIMITED WARRANTY

To the consumer, Royal Appliance Mfg. Co. warrants this product to be free of defects in material or workmanship commencing upon the date of the original purchase. Refer to the data plate label on your product for the length of warranty and save your original sales receipt to validate start of warranty period.

If the product should become defective within the warranty period, we will repair or replace any defective parts free of charge. The complete machine must be delivered prepaid to any ROYAL® Authorized Sales & Warranty Service Station. Please include complete description of the problem, day of purchase, copy of original sales receipt and your name, address and telephone number. If you are not near a Warranty Station, call the factory for assistance at USA & Canada: 1-800-321-1134. Use only genuine Royal ® replacement parts.

The warranty does not include unusual wear, damage resulting from accident or unreasonable use of the product. This warranty does not cover accessories or attachments. This warranty does not cover unauthorized repairs. This warranty gives you specific legal rights and you may also have other rights (Other rights may vary from state to state in the USA).