Kwikset 913CNT 15 913 Smartcode Contemporary Electronic Deadbolt

User Manual

For 913CNT 15.

PDF File Manual, 4 pages, Read Online | Download pdf file

913CNT 15 photo

Other documents for Kwikset 913CNT 15

The following documents are available:
User Manual Dimension Guide Installation Instruction
  • Installation Guide - Spanish - (English) Download
Other Documents
  • Troubleshooting Guide - (English) Download
Photos

Specifications

User Manual - Transcript

  • Page 1 - English - : SMARTCODE “8 Installation and User Guide Required tools Phillips head screwdriver 4 AA Batteries Ruler Kwikset 1-800-327-5625 Additional Tools (depending on application) WWW kwikset com Hammer "| O. .. block ca Prepare the door and check dimensions If drilling a new door. use the supplied template and the complete Measure to confirm that the backset is either 2-3/8" or 2-3/4" (60 or 70 mm). Measure to confirm that the hole in the door is either 2-1/8" (54 mm) or 1-1/2" (38 mm). 2-3/8" or 2-3/4" 60 or 70mm Note: Additional door preparation may be required for doors with 1-1/2" (38 mm) holes. Consult the deadbolt drilling instructions at Py Install the latch and strike Is the door edge chiseled? Latch Interior Assembly Hold the latch in front of the door hole. with the latch Parts in the box Exterior Assembly Traditional Contemporary Contemporary Traditional “B” is not included. If needed. please contact Kwikset to order a drive-in latch for your lock. Fasteners 03809 46780 Strike Keys bs bom 6" N )omx> Q b= Ay PP is —— Adapter Mounting SmartKey 48654 49191 64109 Ring Plate Tool U V er Cm || PP || > Measure to confirm that the door is between 1-3/8" and 2" (35 mm and 51 mm) thick. Measure to confirm that the hole in the door edge is 1" (25 mm). 1-3/8" -2" pa? | MTIRAM= | A Which latch are you installing? face flush against the door edge. chiseled |) \ not Use latch “A”. If the latch bolt is not already extended. extend the latch bolt as shown. Use latch “B” (not included). If the latch bolt is not already extended. extend the latch bolt as shown. D-shaped hole Proceed to next step. Is the D-shaped hole centered in the door hole? No adjustment is required. Latch “A” Latch “B” D-shaped hole Rotate latch face as shown to extend latch. Install strike on the door frame. A\ Make sure the hole in the door frame is drilled a minimum of 1" (25 mm) deep. Longer screws install closest to the door jamb.
  • Page 2 - English - : 3 Install the exterior keypad size What is the diameter of the hole in the door? Install exterior keypad and mounting plate. Diameter is 2-1/8" Diameter is 1-1/2" (54 mm) (38 mm) assembly during mounting plate installation. ZA\ Support exterior N\ “D” is required for installation. “D” is not needed for Install “D” on “F”. installation. Discard “D”. Cable goes underneath latch. Route cable through center hole. then push cable into bottom hole. Insert key and test latch. If latch does not extend or retract smoothly. adjust screws (T). Locate screws for step 3C and keep them within reach. T (=m Remove key when finished and make sure the latch bolt Keep parallelto e is fully extended. edge of door. : Tighten T (2x) screws evenly. 4 Install the interior assembly ee pay Remove battery cover and battery pack from interior assembly. Install interior assembly onto mounting plate. L Ensure tight cable connection. Lay excess cable flat inside the If the turnpiece is pointing down (as bottom of the interior housing. shown above). rotate the turnpiece 180° clockwise until you hear it click. You may need to apply some force. turnpiece shaft is rotated as shown. K Donotinstall = | — | | G@SX¥ppolet ¢ ». U Incorrect: batteries (2x) If turnpiece shaft is not oriented correctly. put the cover back on and L rotate the turnpiece as shown in step A.
  • Page 3 - English - : Set locking and unlocking direction ZA\ CAUTION: Your lock will not function properly if this step is not completed. This step will teach your lock the orientation of your door and is crucial to lock operation. Install 4 AA batteries in battery pack. Press and hold the Lock button. Do not release. The latch bolt will retract and extend to learn the locking and unlocking direction of the door. Make sure the door is open and the latch is extended. Insert the battery pack and continue holding the Lock button. Status LED will indicate success or failure. Success: LED flashes green Failure: LED remains solid red Note: Latch bolt will only retract half way. A\ Ensure correct polarity. For best results. use new. non-rechargeable Alkaline batteries only. If unsuccessful. repeat from step A. moving swiftly between each step. Add user codes (16 max) Programming Timeout During programming. if no button is pressed for five seconds. the system will time out (indicated by three beeps and a red flashing keypad). and you will need to restart the procedure. Enter user code. A total Press Lock button once. of 16 user codes may be programmed. Make sure the door is open. Press the Program button once. What lights and sounds does the lock produce? Each user code must be a unique code between 4 and 8 digits. =e One green flash with one beep Three red flashes with three beeps green —-HAQO®) red —-Q@0O® Programming was successful. Programming was unsuccessful. Make sure not to pause for more than 5 seconds during programming. Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt. Make sure the lock has room for an additional code. If all user code positions are filled. delete a code to make room for this one. Mastercode For enhanced security. a mastercode may be used when adding and deleting user codes. For more information about the mastercode. download the Programming and Troubleshooting Guide on the SmartCode 913 page at www.kwikset.com. *Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. See “Switches and Status LED Colors” on page 4. Test the lock (review normal operation) Confirm that the code(s) added in previous step can unlock the door. Locking the Door Unlocking the Door Press Lock button once. Enter user code. Install the interior cover size WV ato Important Information about the interior cover The window on the For easy access You can now slide up interior cover is to the battery @>-- the window for more locked by default to pack. unlock convenient access prevent someone the window by : 5 to the programming from tampering with removing the 2 buttons and the your lock's settings. security screw. M battery pack while the cover is installed. inside view of interior cover Cover Installation Battery Pack Access If the window is unlocked. slide up the window to access the battery pack. © Install cover. Note: You may M need to rotate the turnpiece to align with the turnpiece shaft. turnpiece If the window is locked. remove the interior cover and screws to access the battery pack.
  • Page 4 - English - : Reference Guide SmartCode at a Glance Re-key the lock (if needed) Exterior Interior (cover removed) © Reinstall battery pack. © Re-key the lock to work with your existing key. See the supplied SmartKey Re-key instructions for more information. © IMPORTANT: Remove battery pack before re-keying. SmartKey LED tool hole Turnpiece Note: When the cover is removed. the turnpiece shaft can be used to manually lock and unlock the door. Switches and Status LED colors Switch | Function Lock Status Door lock status LED blinks every 6 Lock automatically re-locks door 30 seconds after unlocking. Disabled if no codes are programmed. Blinking green Blinking amber Blinking red Low battery Door handing process did not work properly. See the online System Alerts Keypad flashes red three times with three beeps.* One incorrect code entered. Re-enter code. No user code programmed. Program at least one user code. Programming timeout after five Unsuccessful programming. Attempt programming procedure again. Keypad flashes red 15 times with 15 beeps.* Three consecutive incorrect codes entered. Re-enter code after 60 second keypad Keypad flashes red 10 times with 10 beeps.* Low battery. Replace batteries. Keypad flashes green with continuous beeping sound for two seconds.* Deadbolt is jammed and stuck in the locked position. Manually re-lock door. If needed. reposition strike. Keypad flashes red with continuous beeping sound for two seconds.* Deadbolt is jammed and stuck in the unlocked position. Manually re-lock door. If needed. reposition strike. Programing and Troubleshooting Guide. *Beeping sound will only be heard if switch #3 is on. Deleting a single user code Factory Reset Note: All codes may be deleted at once if the mastercode is enabled. For more information about the A factory reset will delete all codes associated with the lock. mastercode. consult the online Programming and Troubleshooting Guide. 2 Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red. battery pack. 4 Press Lock button once. 3 Enter user code to be deleted. 2 Press Lock button once. 1 Keep door open. Press Program button once. 6 Press Lock button once. 5 Re-enter user code. If unsuccessful A\ Test code While the door is open. test the user code to make sure it no longer unlocks 4 Perform the door handing process again to teach the lock the orientation of the door and add user codes to your lock. 3 Press the Program button once more. In 20 seconds. when the LED flashes green and you hear one beep. the lock has been reset. Make sure to enter the same valid code in steps 3 and 5. If no button is pressed for five seconds. the system will time out. and you will need to restart the procedure. Troubleshooting Important Safeguards Read all instructions in their entirety. Familiarize yourself with all warning and caution statements. Remind all family members of safety precautions. Protect your user codes and mastercode. Dispose of used batteries according to local laws and regulations. A complete Programming and Troubleshooting Guide is available on the SmartCode 913 page at www.kwikset.com. CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes. you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a mastercode can help protect your system’s settings. WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means. or evaded by entry elsewhere on the property. No lock can substitute for caution. awareness of your environment. and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk. you should consult a qualified locksmith or other security professional. 4/4 © 2019 Spectrum Brands. Inc.