Loading ...
Loading ...
Loading ...
11
NOTE: The LED indicator is used to indicate the working
status of the pump. When the LED is lit red, the pump is
working properly. When the LED is ashing, it indicates
the pump is overheating. Shut o the pump and let it
cool down before restarting. The pump is also equipped
with overheating protection, which will turn o the unit
automatically when the pump is running dry.
NOTE: A pump running dry may cause overheating. If the
overheating is caused by the pump running dry, make sure
the intake hose is positioned properly in the water.
6. To turn o the pump, press the O (O) side of the On/
O switch (Fig. 8). Remove the battery from the battery
compartment.
Operating Tips
This product is designed for draining or removing water
from ooded areas, clogged sinks, water basins, etc. During
operation, pay attention to the following:
1. Keep the water inlet clean and clear of all foreign objects.
Inspect the water inlet every time before operation.
2. When the water needing to be transferred contains large
particles, or is too shallow to be sucked by the intake
hose, use the equipped puddle strainer. Simply connect
it with the male end of the intake hose, twist to secure,
and place the strainer in the center of the water to be
transferred (Fig. 9).
3. As soon as the pump starts to take in air, turn o the
pump.
NOTE: DO NOT allow the pump to run dry. Damage to the
pump may occur.
4. For best results, the pump should not be placed more
than 18 ft. above the inlet source.
5. During operation, do not block the air vents. This will
cause overheating.
6. Do not run the pump continuously for more than 1 hour.
7. When job is done, turn o the pump and remove the
battery. Disconnect the intake hose and discharge hose.
Make sure no water remains in the hoses before storage.
Maintenance
Please contact an authorized Snow Joe
®
+ Sun Joe
®
dealer
or call the Snow Joe
®
+ Sun Joe
®
customer service center
at 1-866-SNOWJOE (1-866-766-9563) for all maintenance
operations not foreseen in this manual. Any operation
performed in an unauthorized service center or by unqualied
personnel will completely invalidate the warranty.
mCAUTION! To reduce the risk of injury, always remove
battery pack before attempting to install, service, or maintain
the pump. Never disassemble the pump, battery pack or
charger.
General Maintenance
1. Frequently inspect the pump for issues such as abnormal
noise, misalignment or binding of moving parts, breakage
of parts, or any other condition that may aect the tool
operation. Contact your Snow Joe
®
+ Sun Joe
®
dealer or
the Snow Joe
®
+ Sun Joe
®
customer service center for
ALL repairs.
2. Clean dust and debris from vents. Keep handles clean, dry
and free of oil or grease. Only use a dry cloth to clean the
housing, since certain cleaning agents and solvents are
harmful to plastics and other insulated parts. Never use
ammable or combustible solvents around tools.
mWARNING! To reduce the risk of personal injury and
damage, never immerse your tool, battery pack or charger in
liquid or allow a liquid to ow inside them.
Replace the Impeller and O-Ring
IMPORTANT: Only use original replacement lters specied for
this pump.
You can purchase replacement impeller
(Model 24V-XFP5-IMP), O-ring (Model 24V-XFP5-ORING)
and other genuine replacement parts by visiting us online at
sunjoe.com or calling our toll-free customer service helpline at
1-866-SNOWJOE (1-866-766-9563). The use of accessories/
parts that do not meet the original equipment specications
may lead to improper performance of the pump, may
compromise operator safety and will void the manufacturer's
warranty.
Fig. 8
On (I)
On/O switch
O (O)
LED indicator
Fig. 9
Puddle strainer
Intake hose
Loading ...
Loading ...
Loading ...