Loading ...
Loading ...
Loading ...
4 / 4
Alert Reason Solution
Keypad lashes red 3
times with 3 beeps.
Door jammed while
attempting to lock.
Manually re-lock door.
If needed, reposition
strike.
Door handing code
has not been entered.
Enter door handing
code.
No User Code
programmed, or User
Codes are disabled.
Program at least one
User Code, or re-enable
User Codes.
Unsuccessful
programming.
Attempt programming
procedure again.
Incorrect User Code
entered.
Re-enter User Code.
Keypad lashes red 5
times with 5 beeps.
5 incorrect User
Codes entered within
one minute.
Re-enter User Code
after 45-second keypad
lockout.
Keypad lashes red 10
times with 10 beeps.
Low battery. Replace batteries.
© 2018 Spectrum Brands, Inc.
8
Quick Setup and Use
How to add User Codes
A total of 6 User Codes (and a temporary one-time User
Code) may be programmed. Do not program a User Code
that is the same as your Mastercode.
CAUTION: A User Code is used to unlock the door
while a Mastercode is a password for making
changes to the lock features.
1. Make sure the lock is unlocked and the door
is open.
2. Enter your Mastercode - for new install,
default is 0000.
3. Press . You will hear one beep.
4. Press
1
.
5. Press . You will hear one beep.
6. Enter a new User Code. It must be 410 digits.
7. Press . You will hear two beeps if successful. If you
hear three beeps, it was unsuccessful. Repeat from
step 1 slowly.
8. Test the code: While your door is open, lock it. Enter your
new User Code, then press . The door should unlock.
How to delete all User Codes
CAUTION: A User Code is used to unlock the door
while a Mastercode is a password for making
changes to the lock features.
1. Make sure the lock is unlocked and the door
is open.
2. Enter your existing Mastercode - for new install,
default is 0000.
3. Press . You will hear one beep.
4. Press
5
.
5. Press . You will hear two beeps if successful. If
you hear three beeps, it was unsuccessful. Repeat
from step 1 slowly.
For a new installation, this will delete the default User
Code 1234. For subsequent instances, this will delete
all User Codes in the lock.
Now the lock can only be operated by the key and
turnpiece until a new User Code is added in step B.
How to change your Mastercode
The Mastercode will not unlock your door. It is an added
security feature that is used to set up all functions.
The default Mastercode is 0000. It is
recommended that you change it to a code of
your own.
1. Make sure the lock is unlocked and the door is open.
2. Enter your Mastercode - for new install,
default is 0000.
3. Press . You will hear one beep.
4. Press
7
.
5. Press . You will hear one beep.
6. Enter a new Mastercode. It must be between
4 and 10 digits.
7. Press . You will hear two beeps if successful. If you
hear three beeps, it was unsuccessful. Repeat from
step 1 slowly.
BA C
Move swiftly during programming. If no digit is pressed for 10 seconds, the system will time out and you will need to restart the procedure.
This procedure will delete all User Codes associated with the lock, and the
default Mastercode (0000) and User Code (1234) will be restored.
1. Make sure the door is open and unlocked.Press and hold the
Reset button for 5 seconds, until you hear 3 long beeps.
2. Enter the default Mastercode (OOO0).
3. Press . You will hear one beep.
4. Press
0.
5. Press . The latch bolt will extend and retract to learn the
orientation of the door. If successful, the keypad will lash green
and you will hear 2 beeps. If unsuccessful, the keypad will lash
red and you will hear 3 beeps (make sure the door is open and
unlocked and that you are using a fresh set of batteries).
6. Test the lock: With the door open and unlocked, press .
Make sure it locks the door.
7. Test the default User Code: Enter the default User Code (1234), then
press . Make sure it unlocks the door.
The default Mastercode is 0000. It is recommended that
you change it to a code of your own.
The lock is pre-programmed with a default User Code of
1234. It is recommended that you delete this code.
How to restore default settings
System Alerts
Regulatory Compliance
Important Safeguards
Troubleshooting
The lock cannot be locked or unlocked by the keypad.
Make sure the lock is programmed with at least one User
Code and that the User Codes are not disabled. If needed,
restore the lock’s default settings.
The keypad doesn’t respond when touched (no lights
are visible and no beeping is heard).
Make sure the cables are properly connected, and make
sure the batteries are new and installed correctly.
The door can be locked with the Lock button, but the
User Code will not unlock the door.
Make sure the User Code is correct and that the Lock
button is pushed after entering the User Code. If the
door still won’t unlock, use a key to unlock the door. Call
technical support for further troubleshooting.
When the door is closed and the Lock button is pressed
to lock the door, the lock beeps 3 times. When the door
is open and the Lock button is pressed to lock the door,
the lock doesn't beep.
Make sure that the hole in the door frame behind the strike
is drilled at least 1 inch (25 mm) deep. Also make sure
the strike plate is aligned with the latch bolt. If needed,
reposition the strike.
This product complies with standards established by the following regulatory bodies:
• Federal Communications Commission (FCC)
• Industry Canada
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
( 1 ) this device may not cause harmful interference, and
( 2 ) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT! Changes or modiications not expressly approved by the manufacturer could void the user’s authority to operate the
equipment.
Industry Canada
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: ( 1 ) this
device may not cause interference, and ( 2 ) this device must accept any interference, including interference that may cause undesired
operation of the device.
1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Restrict access to your lock’s interior assembly and routinely
check your settings to ensure they have not been altered
without your knowledge.
5. Protect your User Codes and Mastercode.
6. Dispose of used batteries according to local laws and regula-
tions.
CAUTION: Prevent unauthorized entry. This lock has a pre-set User
Code and Mastercode. Upon installation and set-up, replace both of
these codes with your own. Since anyone with access to the interior
assembly can reset the lock and change the User Codes, you must
restrict access to the interior assembly and routinely check the User
Codes to ensure they have not been altered without your knowledge.
WARNING: This Manufacturer advises that no lock can provide
complete security by itself. This lock may be defeated by forcible or
technical means, or evaded by entry elsewhere on the property. No
lock can substitute for caution, awareness of your environment, and
common sense. Builder’s hardware is available in multiple perfor-
mance grades to suit the application. In order to enhance security and
reduce risk, you should consult a qualiied locksmith or other security
professional.
9
Additional Programming Features
How to change Auto-Lock time delay
You can set the Auto-Lock time delay to
10, 20, 30, 40, or 50 seconds.
1. Make sure the lock is unlocked and the door
is open.
2. Enter your existing Mastercode.
3. Press . You will hear one beep.
4. Press
1 - 3.
5. Press . You will hear one beep.
6. For 10 seconds, press 1.
For 20 seconds, press 3.
For 30 seconds, press 5.
For 40 seconds, press 7.
For 50 seconds, press 9.
7. Press . You will hear two beeps if successful. If you
hear three beeps, it was unsuccessful. Repeat from
step 1 slowly.
How to enable/disable Auto-Lock
The Auto-Lock feature automatically re-locks your door
30 seconds after unlocking. This feature is o by default.
1. Make sure the lock is unlocked and the door
is open.
2. Enter your existing Mastercode.
3. Press . You will hear one beep.
4. Press
1 - 1
.
5. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
How to add a one-time User Code
A one-time user code may be used only once, and then it will
be deleted immediately after use.
1. Make sure the lock is unlocked and the door is open.
2. Enter your existing Mastercode.
3. Press . You will hear one beep.
4. Press
1 - 9
.
5. Press . You will hear one beep.
6. Enter a new User Code. It must be 410 digits.
7. Press . You will hear two beeps if successful. If you
hear three beeps, it was unsuccessful. Repeat from
step 1 slowly.
How to delete individual User Codes
The lock is pre-programmed with a default
User Code of 1234. It is recommended
that you delete this code.
1. Make sure the lock is unlocked and the door
is open.
2. Enter your existing Mastercode.
3. Press . You will hear one beep.
4. Press
3.
5. Press . You will hear one beep.
6. Enter the User Code you wish to delete.
7. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
8. Test the code: While your door is open, lock it. Enter the
User Code, then press . The door should not unlock.
How to enable/disable User Codes
If User Codes are disabled (example: when you go on
vacation), the lock can only be operated by the key and
turnpiece until they are enabled again.
1. Make sure the lock is unlocked and the door is open.
2. Enter your existing Mastercode.
3. Press . You will hear one beep.
4. Press
1 - 7
.
5. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
How to mute/unmute lock
If the lock is muted, you will not hear beeping during
programming, normal operation, low battery indicators, or
system alerts.
1. Make sure the lock is unlocked and the door is open.
2. Enter your Mastercode.
3. Press . You will hear one beep.
4. Press
1 - 5
.
5. Press . You will hear two beeps if successful. If you
hear three beeps, it was unsuccessful. Repeat from
step 1 slowly.