GE GFE26JYMFS 36 Inch 25.6 Cu. Ft. Fingerprint Resistant French-Door Refrigerator

OPERATING INSTRUCTIONS

Features

French Door Models

Controls

NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not removed during installation, remove it now.

Dispenser*

Water & Ice Dispenser

Press the glass gently against the dispenser cradle. The spill shelf is not self-draining. To reduce water spotting, the shelf should be cleaned regularly.

If no water is dispensed when the refrigerator installed, there may be air in the water line system. Press the dispenser paddle for at least five minutes to remove trapped air from the water line and to fill the water system. To flush out impurities in the water line, throw away the first six full glasses of water.

Door Ice Bin

1. Open left fresh food door.
2. Pull down latch to release bin door.
3. Using handhold. lift ice bucket up and out to clear locators in bottom of bin
4. To replace the ice bucket. set iton the guide brackets and push until the ice bucket seats properly.
5. If bucket cannot be replaced. rotate the Ice Bucket Fork 1/4 tum clockwise.

Internal Water Dispenser (on some models)
The water dispenser is located on the left wall inside the refrigerator compartment.
To dispense water:

1. Hold the glass against the recess.
2. Push the water dispenser button.
3. Hold the glass underneath the dispenser for 2-3 seconds after a releasing the dispenser button.Water may continue to dispense after the button is released.

lf no water is dispensed when the reftigerator is first installed. there may be air in the water line system. Press the dispenser button for at least 5 minutes to remove trapped air from the water line and to fill the water system. During this process. the dispenser noise may be loud as the air is purged from the water line system. To flush out impurities in the water line. throw away the first 6 glassfuls of water.

NOTE: To avoid water deposits. the dispenser should be cleaned periodically by wiping with a clean cloth or sponge.

Important Facts About Your Dispensers

• Do not add ice from trays or bags to the door icemaker bucket. It may not crush or dispense.
• Avoid overfilling glass with ice and use of narrow glasses. Backed-up ice can jam the chute or cause the door in the chute to freeze shut. If ice is blocking the chute remove the ice bucket. poke it through with a wooden spoon.
• Beverages and foods should not be quick-chilled in the door icemaker bin. Cans. bottles or food packages in the storage drawer may cause the icemaker or auger. to jam
• To keep dispensed ice from missing the glass. put the glass close to. but not touching. the dispenser opening.
• Some crushed ice may be dispensed even though you selected CUBED ICE. This happens occasionally when a few cubes accidentally get directed to the crusher.
• After crushed ice is dispensed. some water may drip from the chute.
• Sometimes a small mound of frost will form on the door in the ice chute. This condition is normal and usually occurs when you have dispensed crushed ice repeatedly.

Water Filter - MWF

Water Filter Cartridge
The water filter cartridge is located in back upper right comer of the refrigerator compartment.

• When to replace the filter on models with a replacement indicator light
  • There is a replacement indicator light for the water filter cartridge on the dispenser. A red light will start blinking to tell you that you need to replace the filter soon.
  • The filter cartridge should be replaced when the replacement indicator light turns red or if the flow of water to the dispenser or icemaker decreases.
• When to replace the filter on models without a replacement indicator light
  • The filter cartridge should be replaced every six months or earlier if the flow of water to the dispenser or icemaker decreases.
• Removing the filter cartridge
  • If you are replacing the cartridge. first remove the old one by slowly turning it to the left. Do not pull down on the cartridge. A small amount of water may drip down.

NOTE: To reduce the risk associated with property damage due to water leakage. read and follow instructions before installation and use of this system. Installation and use MUST comply with all sate and local plumbing codes.

CAUTION: If air has been trapped in the system. the filter cartridge may be ejected as it is removed. Use caution when removing.

Installing the Filter Cartridge

1. Fill the replacement cartridge with water from the tap to allow for better flow from the dispenser immediately after installation.
2. Line up the arrow on the cartridge and the cartridge holder. Place the top of the new cartridge up inside the holder. Do not push it up into the holder.
3. Slowly turn it to the right until the filter cartridge stops. DO NOT OVERTIGHTEN. As you turn the cartridge. it will automatically raise Cartrfage itself into position. The cartridge will Holder move about a 1/2 turn.
4. Run water from the dispenser for 1-1/2 gallons (about three minutes) to clear the system and prevent sputtering.
5. Press and hold the RESET WATER FILTER pad (on some models) on the dispenser for three seconds.

NOTE: A newly installed water filter cartridge may cause water to spurt from the dispenser.

Filter Bypass Plug

You must use the filter bypass plug when a replacement filter cartridge is not available. The dispenser and the icemaker will not operate without the filter or filter bypass plug.

Water Filter - XWF

Water Filter Cartridge

The water filter cartridge holder is located in the back upper-right comer of the fresh food refrigerator compartment.

When to Replace the Filter

If there is a replacement indicator light for the water filter cartridge on the dispenser. the red filter light will start blinking to tell you that you need to replace the filter soon.

• For external control models. the filter light will blink while you are dispensing until the filter is replaced.
• For top control models. the filter light will blink while the door is open until the filter is replaced.

For models that don't have the indicator light. the filter cartridge should be replaced every six months. or earlier if the flow of water to the dispenser or icemaker decreases.

Removing the Filter

If you are replacing the filter. first remove the previous one:

1. Open the filter cartridge housing by squeezing the 2 front tabs and gently pulling down.
2. Rotate the filter down.
3. Gently grasp the filter and slowly turn it counterclockwise about a % turn. The filter should automatically release itself when you have rotated it far enough to the left. A small amount of water may drip down.

CAUTION: If air has been trapped in the system. the filter cartridge may be ejected as it is removed. Use caution when removing.

Filter Bypass Plug

To reduce the risk of property damage due to water leakage. you MUST use the filter bypass plug when a replacement filter cartridge is not available. Some models do not come equipped with the filter bypass plug. To obtain a free bypass plug. call 800-GECARES. In Canada. call 800.561.3344. The dispenser and icemaker will not operate without either the filter or bypass plug installed. The bypass plug is installed in the same way as. a filter cartridge

Installing the Filter in a Bottom Freezer Refrigerator

1. Open the filter cartridge housing by squeezing the 2 front tabs and gently pulling down.
   
2. Line up the ports on the filter with the ports on the filter cartridge holder. and gently insert the filter.
3. Slowly turn the filter to the right until it stops. DO NOT OVERTIGHTEN. As you turn the filter. it will automatically adjust itself into position. The filter will move about a % turn or 90 degrees. until the arrow on the filter aligns with the arrow on the filter cartridge holder.
   
4. Slowly push the filter up into the clips.
5. Close the filter cartridge housing by gently pushing the lid upwards until the tabs lock into place.
   
6. Run water from the dispenser for 2 gallons (7.6 liters) or approximately 5 minutes to clear the system. Water may spurt out and air bubbles may be visible during this process. If water is not flowing. check to make sure the filter has been fully rotated to the right.
7. Press and hold the WATER FILTER pad (only on select models) on the dispenser for three seconds.

Application Guidelines/Water Supply

• Service Flow: 0.5 gpm (1.89 Ipm)
• Water Supply: Potable Water
• Water Pressure: 25-120 psi (172-827 kPa)
• Water Temperature: 33°F-100°F (0.6°C-38°C)
• Capacity: 170 gallons (643.5 liters)

Sign-up for TEXT REMINDERS by texting REPLACE to 70543.

Shelves and Bins

Not all features are on all models

Rearranging the Refrigerator Shelves
Shelves in the refrigerator compartment are adjustable.

To remove the shelves:

1. Remove all items from the shelf.
2. Tilt the shelf up at the front.
3. Lift the shelf up at the back and bring the shelf out.

To replace the shelves:

1. While tilting the shelf up. insert the top hook at the back of the shelf in a slot on the track.
2. Lower the front of the shelf until the bottom of the shelf locks into place.

Quick Space Shelf (on some models)
This shelf splits in half and slides under itself for storage of tall items on the shelf below.

This shelf can be removed and replaced or relocated.

NOTE: The back half of the Quick Space Sheff is not adjustable.

Adjustable Door Bins (on some models)

• To remove: Lift the bin straight up; then pull out.
• To replace: Engage the bin in the molded supports on the door and push down to lock in place.

Non-Adjustable Gallon Door Bins (on some models)

• To remove: Lift the bin straight up; then pull out.
• To replace: Engage the bin in the molded supports on the door and push down to lock in place.

Pans

Climate Zone Pans

Keep fruits and vegetables organized in separate compartments for easy access. Excess water that may accumulate in the bottom of the drawers or under the drawers should be wiped dry.

To remove pan:

Slide the pan out to the stop position. lift the pan up and past the stop position and pull forward.

Full -Width Pan (on some models)
To remove pan:

1. Pull the pan out to the stop position.
2. Lift the front of the drawer up and out.
   

To replace pan:

1. Place back of the drawer in first and rotate drawer front down to seat it on the slides.
2. Push the drawer in to the closed position.

How to Remove and Replace Drawer Divider
To remove:

1. Pull the drawer out to the stop position.
2. Slide pan divider to right to release it from pan.

To replace:

Reverse steps 1 and 2 to replace drawer divider.

Floating Snack Pan (on some models)

This pan can be moved to the most useful location for your family's needs.

To remove: slide the pan out to the stop position. lift the pan up and past the stop position and lift it out.

Freezer Drawer*

FREEZER BASKETS

1. An ice bucket in the top basket (on some models).
2. A top full-width basket.
3. A bottom full-width basket (with divider - in some models)

NOTE: Do not fil baskets higher than the rim of the basket. This may cause baskets to stick or jam Appearance and features when opening or closing.

Top Basket Removal

To remove the top full-width basket on freezer drawer models:

1. Pull the basket out to the stop location.
2. Lift basket up to release it from the slides.
   

When replacing the basket, make sure that the basket. remains mounted on the side rails and over the slides of the bottom basket.

NOTE: Always be sure to fully close this basket.

Bottom Basket Removal

To remove the bottom full-width basket on freezer drawer models:

1. Open the bottom freezer drawer until it stops.
2. Remove the top freezer basket
3. The bottom freezer basket rests on the inside tabs on the drawer slides.
4. Lift the front of the basket and pull forward.
5. Release the pin from the slot to remove the basket.
   

When replacing the bottom full-width basket, tilt the basket back and lower it into the drawer. Rotate the basket to a horizontal position and press down. Make sure to place the pin back into the slot.

NOTE: Always be sure that the basket is seated on the bracket tabs before sliding the drawer back into the freezer.

Freezer Compartment

FREEZER SHELF AND BASKET

1. A full-width fixed wire shelf
2. A full-width sliding plastic basket
   

NOTE: Do not fill baskets A higher than the rim. This may cause basket to stick or jam when opening or closing.

Basket Removal

To remove the full-width sliding basket on freezer door models:

1. Open the basket out to its full extension.
2. Lift up the front of the basket and pull straight out to remove.
   

When replacing the basket. insert the plastic basket into the lower liner rails and push back into place.

Fixed Shelf Removal
NOTE: The full-width wire shelf is not intended to slide.

To remove for cleaning, push the shelf to one side while then pull up on the opposite side and out to remove

To replace the full-width wire shelf, insert one side of the shelf into the supports. pushing the shelf to that side until the opposite side will fit into its supports.

Automatic Icemaker

Automatic Icemaker (on some models)

The icemaker will produce seven cubes per cycle approximately 100-130 cubes in a 24-hour period. depending on freezer compartment temperature. room temperature, number of door openings and other use conditions.

If the refrigerator is operated before the water connection is made to the icemaker. set the power switch in the OFF position.

When the refrigerator has been connected to the water supply. set the power switch to the ON position.

The icemaker will fil with water when it cools to 15°F (-10°C). A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes.

You may hear a buzzing sound each time the icemaker fills with water.

Throw away the first few — EOWer batches of ice to allow the water line to clear.

Be sure nothing interferes with the sweep of the feeler arm.

When the bin fills to the level of the feeler arm. the icemaker will stop producing ice. It is normal for several cubes to be joined together.

If ice is not used frequently. old ice cubes will become cloudy. taste stale and shrink

NOTE: In homes with lower-than-average water pressure. you may hear the icemaker cycle multiple times when making one batch of ice.

For Refrigerator Models with Icemaker in the Door Ice Bucket and Dispenser

• Open the ice box door on inside of the left door.
• Pull up and out on the ice bucket in the left hand door to remove it from the compartment.
• To replace the ice bucket. set it on the guide brackets and push until the ice bucket seats properly.
• If bucket cannot be replaced. rotate the ice bucket fork 1/4 tum clockwise.
• Icemaker can be turned on and off using this display (see Controls on pages 7 and 8.) |e bucket le bucket fork

For Refrigerator Models with Icemaker in the Freezer Compartment

Some models come with an icemaker installed in the freezer compartment. For those models that come ice-maker ready. you can purchase Kit IM4D. Visit our website at GEAppliances.com or call GE Appliances Parts and Accessories. 877.959.8688 (in Canada visit geappliances.calen/products/parts-filters accessories or call 1.800.661.1616).

There is ice storage in the freezer compartment located on the left side of the upper basket. Pull the upper basket forward to remove the ice bucket.

CARE AND CLEANING

Replacing the Lights

There is LED lighting in the fresh food compartment at the top center and on the left and right sides above the climate zone pans on the french door models.

LED lighting is located at the top of the fresh food compartment on the single door models.

LED lights are also located at the top of the left and right sides of the freezer in all models.

An authorized technician will need to replace the LED light.

If this assembly needs to be replaced. call GE
Appliances Service at 1.800.432.2737 in the United
States or 1.800.561.3344 in Canada

INSTALLATION INSTRUCTIONS

Preparing to Install the Refrigerator
PREPARATION
MOVING THE REFRIGERATOR INDOORS
If the refrigerator will not fit through a doorway. the refrigerator door and freezer drawer or door can be removed.

• To remove the refrigerator door. see Step 1 in the Reversing the Door Swing section.
• To remove the freezer drawer. see the Removing the Freezer Drawer section.

WATER SUPPLY TO THE ICEMAKER AND DISPENSER

If the refrigerator has an icemaker. it will have to be connected to a cold water line. A
GE Appliances water supply kit (containing tubing. shutoff valve. fittings and instructions) is available at extra cost from your dealer. by visiting our website at GEAppliances.com (in Canada at GEAppliances.ca) or from Parts and Accessories. 877.959.8688 (in Canada 1.800.661.1616).

Appliance Dimensions

Installing the Water Line

CONNECTING TO THE HOUSE WATER LINE (icemaker models only)

A cold water supply is required for automatic icemaker operation. If there is not a cold water supply. you will need to provide one. See Installing the Water Line section.

NOTES:

• Before making the connection to the refrigerator. be sure the refrigerator power cord is not plugged into the wall outlet.
• If your refrigerator does not have a water filter. we recommend installing one if your water supply has sand or particles that could clog the screen of the refrigerator's water valve. Install it in the water line near the refrigerator. If using SmartConnect
• Refrigerator Tubing Kit. you will need an additional tube (WX08X10002) to connect the filter. Do not cut plastic tube to install filter.
• Before connecting the water line to the house. purge the house line for at least 2 minutes.

A. If you are using copper tubin, place a compression nut and ferrule (sleeve) onto the end of the tubing coming from the house cold water supply.

If you are using the SmartConnect tubing. the nuts are already assembled to the tubing.

B. If you are using copper tubing, insert the end of the tubing into the refrigerator connection. at the back of the refrigerator. as far as possible. While holding the tubing. tighten the fitting
If you are using SmartConnect tubing. insert the molded end of the tubing into the refrigerator connection. at the back of the refrigerator. and tighten the compression nut until it is hand tight.
Then tighten one additional turn with a wrench.
Over tightening may cause leaks.

C. Fasten the tubing into the clamp provided to hold it in position. You may need to pry open the clamp.

One of the illustrations below will look like the connection on your refrigerator.

Connect to potable water supply only.

A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 psi (275-827 kilopascals).

TURN ON THE WATER SUPPLY (icemaker models only)

Turn the water on at the shutoff valve (house water supply) and check for any leaks

PLUG IN THE REFRIGERATOR

On models with an icemaker. before plugging in the = refrigerator. make sure the icemaker power switch is set to the 0 (off) position. See the grounding information attached to the power cord.

INSTALLING THE WATER LINE

1. SHUT OFF THE MAIN WATERSUPPLY
   Turn on the nearest faucet long enough to clear the line of water.
2. CHOOSE THE VALVE LOCATION
   Choose a location for the valve that is easily accessible. It is best to connect into the side of a vertical water pipe. When it is necessary to connect into a horizontal water pipe. make the connection to the top or side. rather than at the bottom. to avoid drawing off any sediment from the water pipe.
   
3. DRILL THE HOLE FOR THE VALVE
   • Drill a 1/4” hole in the water pipe (even if using a self-piercing valve). using a sharp bit. Remove any burrs resulting from drilling the hole in the pipe.
   • Take care not to allow water to drain into the drill.
   • Failure to drill a 1/4” hole may result in reduced ice production or smaller cubes.
     

FASTEN THE SHUTOFF VALVE
Fasten the shutoff valve to the cold water pipe with the pipe clamp.

TIGHTEN THE PIPE CLAMP
Tighten the clamp screws until the sealing washer begins to swell.
NOTE: Do not over tighten or you may crush the tubing.

ROUTE THE TUBING
Route the tubing between the cold water line and the refrigerator.
Route the tubing through a hole drilled in the wall or floor (behind the refrigerator or adjacent base cabinet) as close to the wall as possible.

FASTEN THE SHUTOFF VALVE
Place the compression nut and ferrule (sleeve) for copper tubing onto the end of the tubing and connect it to the shutoff valve.
Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely.
For plastic tubing from a SmartConnect
Refrigerator Tubing kit. insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight. then tighten one additional turn with a wrench. Over tightening may cause leaks.

NOTE: Commonwealth of Massachusetts
Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

FLUSH OUT THE TUBING
Turn the main water supply on and flush out the tubing until the water is clear.
Shut the water off at the water valve after about one quart (1 liter), or 2 minutes. of water has been flushed through the tubing.

TROUBLESHOOTING TIPS

Troubleshooting Tips... Before you call for service

• Refrigerator does not operate
  • Refrigeratorin defrost cycle.
    • Wait about 30 minutes for defrost cycle to end.

Either or both conirols set to OFF.

Set the controls to a lower temperature setting

Refrigeratoris unplugged

Push the plug completely into the outlet.

The fuse is blown/circuit breaker is tripped.

Replace fuse or reset the breaker.

Refrigerator is in showroom mode.

Unplug the refrigerator and plug it back in.

Vibration or rattling (slight vibration is normal)

Leveling legs need adjusting.

See Level the refrigerator.

Motor operates for long periods or cycles on and off frequently. (Modem refrigerators with more storage space and a larger freezer require more operating time. They start and stop often to maintain even temperatures.)

Normal when refrigerator is first plugged in

Wait 24 hours for the refrigerator to completely cool down.

Often ocours when large amounts of food are placed in refrigerator.

This is normal.

Door left open

Check to see if package is holding door open.

Hot weather or frequent door openings.

This is normal.

Temperature controls set at the coldest setting.

See Controls section

Refrigerator or freezer compartment too warm

Temperature control not set cold enough.

See Controls section

Warm weather or frequent door openings.

Set the temperature control one step colder.

See Controls section

Door left open

Check to see if package is holding door open.

Frost or ice crystals on frozen food (frost within package is normal)

Door left open

Check to see if package is holding door open.

Too frequent or too long door openings.

This is normal.

Divider between refrigerator and freezer compartments feels warm

Automatic energy saver system circulates warm liquid around front edge of freezer compartment.

This helps prevent condensation on the outside.

Automatic icemaker does not work

Icemaker power switch is in the OFF position.

Set the power switch to the ON position

Water supply turned off or not connected.

See Installing the Water Line section

Freezer compartment too warm:

Wait 24 hours for the refrigerator to completely cool down.

Piled up cubes in the storage bin cause the icemaker to shut off.

Level cubes by hand.

Ice cubes stuck in icemaker.

Tum off the icemaker. remove cubes. and turn the icemaker back on.

Freezer cooling, fresh food not cooling

Normal. when refrigerator first plugged in or after extended power outage.

Wait 24 hours for temperature in both compartments to reach selected temperatures.

Ice dispenser opens after closing freezer drawer (on some models)

Normal

The ice dispenser door may open after closing freezer door to allow access.

• Ice cubes have odor/taste
  • Ice storage bin needs cleaning.
    • Empty and wash bin. Discard old cubes.
  • Food transmitting odoritaste to ice cubes.
    • Wrap foods well
  • Interior of refrigerator needs cleaning.
    • See Care and Cleaning section
• Small or hollow cubes
  • Water filter clogged.
    • Replace filter cartridge with new cartridge or with plug.
• Slow ice cube freezing
  • Door left open.
    • Check to see if package is holding door open.
  • Temperature control not set cold enough.
    • See Controls section
• Frequent buzzing sound”
  • Icemaker power switch is in the | (on) position. but the water supply to the refrigerator has not been connected.
    • Set the power switch to the 0 (off) position. Keeping it in the | (on) position will damage the water valve:
• Orange glow in the freezer
  • Defrost heater is on.
    • This is normal
• Water has poor taste/odor
  • Water dispenser has not been used for a long time
    • Dispense water until all water in system is replenished.
• Water in first glass is warm.
  • Normal when refrigerator is first installed.
    • Wait 24 hours for the refrigerator to completely cool down.
  • Water dispenser has not been used for a long time
    • Dispense water until all water in system is replenished.
  • Water system has been drained.
    • Allow several hours for replenished supply to chil
• Water dispenser does not work
  • Water supply line turned off or not
    • See Installing the waterline section connected.
  • Water fter clogged.
    • Replace fiter cartridge or remove filter and install plug.
  • Air may be trapped in the water system.
    • Press the dispenser arm for at least two minutes.
  • Dispenser is LOCKED.
    • Press and hold the LOCK pad for 3 seconds.
• Water spurting from dispenser
  • Newly-installed fier cartridge.
    • Run water from the dispenser for 3 minutes (about one and a hatf gallons).
• Water is not dispensed but icemaker is working
  • Water in reservoir is frozen
    • Call for service.
  • Refrigerator control setting is too cold.
    • Set to a warmer setting
• No water orice cube production
  • Supply line or shutoff vaive is clogged
    • Call a plumber.
  • Water fter clogged
    • Replace fiter cartridge or remove filter and install plug.
• Refrigerator has odor
  • Foods transmitting odor to refrigerator.
    • Foods with strong odors should be tightly wrapped. Keep an open box of baking soda in the refrigerator; replace every three months.
  • Interior needs cleaning.
    • See Care and Cleaning section
• Moisture forms on outside of refrigerator
  • Not unusual during periods of high humidity.
    • Wipe surface dry.
• Moisture collects inside (in humid weather. air carries moisture into refrigerator when doors are opened)
  • Too frequent or too long door openings.
    • This is normal
  • Due to the higher humidity in the refrigerator. you may on occasion experience fog or small amounts of moisture in the refrigerator compartment.
    • This is normal and may come and go as different food loads and environmental conditions change. Wipe dry with a paper towel if desired.
• Interior light does not work
  • No power at outlet.
    • Replace fuse or reset the breaker.
  • LED lights are out
    • Call Service - see Replacing the Lights
• Hot air from bottom of refrigerator
  • Normal air flow cooling motor. In the refrigeration process. itis normal that heat be expelled in the area under the refrigerator. Some floor coverings are sensitive and will discolor at these normal and safe temperatures.
    • This is normal.
• Refrigerator never shuts off but the temperatures are OK
  • Adaptive defrost keeps compressor running during door openings.
    • This is normal. The refrigerator will cycle off after the door remains closed for 2 hours.
• Refrigerator is beeping
  • Door is open.
    • Close door.
• Door not closing properly
  • Door gasket on hinge side sticking or folding over.
    • Apply paraffin wax to the face of the gasket.
• Actual temperature not equal to Set temperature
  • Unit just plugged in.
    • Allow 24 hours for system to stabilize
  • Door open for too long.
    • Allow 24 hours for system to stabilize
  • Warm food added to refrigerator.
    • Allow 24 hours for system to stabilize
  • Defrost cycle is in process.
    • Allow 24 hours for system to stabilize
• Door/drawer does not close by itself
  • Leveling legs need adjusting.
    • See level the refrigerator
• Freezer door/drawer pops open when refrigerator door is closed
  • This is normal if, after popping open, the freezer door/drawer closed on its own.
    • This indicates that there is a good seal on the freezer door/drawer. If the freezer door/drawer does not automatically close after popping open. then see the Problem: Door! drawer does not close by itself, above.
• Food freezing in the refrigerator
  • Food too close to the air vent at the back of the refrigerator.
    • Move the food away from the air vent
  • Refrigerator control is set too cold.
    • Move the refrigerator control fo a warmer temperature setting one increment at a time.
• Water is leaking from dispenser
  • Glass not being held under the dispenser long enough after button is released.
  • Hold the glass undemeath the dispenser for 2-3 seconds after releasing the dispenser button. Water may continue to dispense after the button is released
  • Air may be present in the water line system, causing water to drip after being dispensed.
  • Dispense water for at least 2 minutes to remove air from system.
• My display is showing tc
  • Turbo Cool function is activated.
    • See Controls section
• Water filter indicator light changed color
  • This is normal
    • See Water Filter Cartridge - MWF or XWF remains
• Water filter indicator light remains red even after replacing the water fitter
  • Water filter indicator must be reset.
    • Press and hold the WATER FILTER pad for 3 seconds. See Water Filter Cartridge - MWF or XWF section.
• Water filter indicator light is not fit
  • This is normal. The fiter cartridge should be replaced when the replacement indicator light turns red.
    • See Water Filter Cartridge - MWF or XWF section
• Handle is loose / handle has a gap.
  • Handle needs adjusting.
    • See Attach the Fresh Food Handle and Attach the Freezer Handle sections
• Refrigerator doors are not even (on French Door models only)
  • Doors need realigning.
    • See Level the Refrigerator Doors section.
• Baskets stick or jam when opening or closing
  • Baskets are too full
    • To open: remove some of the products from the basket when opened as far as possible. Readjust the products left in the basket and try to open the basket again. To close: readjust products in the basket or remove any product that is above the rim of tis banked and close the basket.

Related Products