Loading ...
Loading ...
Loading ...
13
Replacing the Produce Preserver Pouches
The disposable pouches should be replaced every 6 months,
when the status indicator has completely changed from white to
red.
To order replacements, see the contact information in the Quick
Start Guide. Order part number W10346771A or FRESH1.
1. Remove the used pouches from the produce preserver
housing.
2. Remove the used status indicator.
3. Install the new pouches and status indicator using the
instructions in the previous sections or instructions included in
the replacement packets.
REFRIGERATOR FEATURES
Crisper Humidity Control (on some
models)
You can control the amount of humidity in the moisture-sealed
crisper. Depending on your model, adjust the control to any setting
between Fruit and Vegetables or Low and High.
Fruit/Low (open):
Move control to allow moist air out of the crisper for best storage
of fruits and vegetables with skins.
� Fruit: Wash, let dry and store in refrigerator in plastic bag or
crisper. Do not wash or hull berries until they are ready to use.
Sort and keep berries in original container in crisper, or store in
a loosely closed paper bag on a refrigerator shelf.
� Vegetables with skins: Place in plastic bags or plastic
container and store in crisper.
Vegetables/High (closed):q
Move control to keep moist air in the crisper for best storage of
fresh, leafy vegetables.
� Leafy vegetables: Wash in cold water, drain and trim or tear off
bruised and discolored areas. Place in plastic bag or plastic
container and store in crisper.
Water and Ice Dispensers (on some
models)
For additional information on how to use your water and ice
dispensers, see the online “Dispensing Guide.”
IMPORTANT:
� After connecting the refrigerator to a water source or replacing
the water filter, flush the water system. Use a sturdy container
to depress and hold the water dispenser pad for 5 seconds,
then release it for 5 seconds. Repeat until water begins to flow.
Once water begins to flow, continue depressing and releasing
the dispenser pad (5 seconds on, 5 seconds off) until a total of
4 gal. (15 L) has been dispensed. This will flush air from the
filter and water dispensing system, and prepare the water filter
for use. Additional flushing may be required in some
households. As air is cleared from the system, water may spurt
out of the dispenser.
� Allow 24 hours for the refrigerator to cool down and chill water.
Dispense enough water every week to maintain a fresh supply.
� Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
� The dispenser will dispense either water or ice.
� The dispensing system will not operate when the refrigerator
door is open.
� On some models, the display screen on the dispenser control
panel will turn off automatically and enter “sleep” mode when
the control buttons and dispenser levers have not been used
for 2 minutes or more. While in “sleep” mode, the first press of
a control button will only reactivate the display screen without
changing any settings. After reactivation, changes to any
settings can then be made. If no changes are made within 2
minutes, the display will re-enter “sleep” mode.
Flush the Water System
Air in the water dispensing system can cause the water dispenser
to drip. After connecting the refrigerator to a water source or
replacing the water filter, flush the water system.
Flushing the water dispensing system forces air from the water
line and filter and prepares the water filter for use. Additional
flushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out of
the dispenser.
1. Using a sturdy container, depress and hold the water
dispenser paddle for 5 seconds.
2. Release the dispenser paddle for 5 seconds. Repeat steps 1
and 2 until water begins to flow.
3. Once water begins to flow, continue depressing and releasing
the dispenser pad (5 seconds on, 5 seconds off) until a total of
3 gal. (12 L) has been dispensed.
Loading ...
Loading ...
Loading ...