Loading ...
Loading ...
Loading ...
10
Operating Your Dishwasher
Starting Your Dishwasher
IMPORTANT
If the dishwasher drain line is connected to
a garbage disposal, run the disposal before
operating the dishwasher for proper drainage.
1. Open the door and push in on the
main power switch on the top of the
door so that it is in the on position.
The control panel on the front of the
dishwasher is lit when the switch is on.
2. Close the door. Push in gently on the top of the
door until it clicks shut.
3. Touch the PROGRAM touch key repeatedly until
the indicator light for the desired wash cycle is lit.
See the facing page for a description of the wash
cycles.
4. If you want to change the wash
temperature setting, touch the Wash
Temperature key repeatedly to toggle
between the “normal” setting and the “high”
setting. The light on the Wash Temperature
key is lit when the temperature is set to “high.”
See the facing page for a description of the
temperature settings.
5. If you want to change the dish drying
time, touch Dry repeatedly to toggle
between the “normal” and “high” setting.
The light on the Dry cycle key is lit when the
dry time is set to “high.” NOTE: When set to
“normal”, the rinse water temperature is lower,
causing the dishes to take longer to dry. Change
the setting to “high” if the dishes do not dry
properly.
6. Touch the START/STOP touch key for 3
seconds. The display will ash three times to
indicate that the dishwasher is starting. If only
horizontal lines appear on the
display, the door is ajar. Push
in gently on the top of the door
until it clicks shut.
During Operation
• Once you have selected a cycle and options, the
display indicates how long the cycle took the last
time it was used. Once you start the dishwasher,
the display shows the estimated time until the
end of the new cycle. The display changes
periodically as the dishwasher recalculates the
cycle time based on water temperature.
• If power to the dishwasher is turned off at the
main power switch or if there is a power outage
before the wash cycle completes, the selected
cycle will continue when the power is restored.
However, if power is interrupted or the door is
open more than two minutes during drying, the
cycle will end.
Adding a Dish After You Start
You can add a dish, if needed, after starting your
dishwasher. Dacor recommends that you only add
items during the rst ve minutes of operation to
make sure they get clean.
To add a dish:
1. Slowly open the door. The dishwasher will stop
operating. Wait a moment for the steam to clear.
2. Without touching any hot surfaces, dishes or
racks, insert the item into one of the racks,
following the normal loading instructions.
3. Close the door. Push in on the top of the door to
make sure that it is completely shut. Operation
will resume.
Standby Mode
Once the cycle is nished, the dishwasher will beep
and End will appear on the display. When the cycle
completes, the dishwasher draws a very small
amount of power. Open the door and push the main
power switch to turn power off completely.
Stopping Your Dishwasher During
Operation
Touch the START/STOP touch key for ve seconds.
The dishwasher will stop operating.
Changing the Wash Cycle After You
Start
You can change the cycle, the wash temperature or
the dry setting after you start your dishwasher.
1. Open the door, then touch the START/STOP
key for ve seconds. The dishwasher will stop
operating.
2. If the detergent dispenser door has opened, add
more detergent.
3. Touch the PROGRAM key repeatedly to select
the new wash cycle (the indicator for the desired
wash cycle will light).
4. If you want to change the wash temperature
or dry setting, touch the key for that function
repeatedly to toggle between settings.
5. Touch START/STOP for 3 seconds, wait for the
display to ash three times, then close the door.
Loading ...
Loading ...
Loading ...