Loading ...
Loading ...
Loading ...
7
PROBLEM Possible Causes and/or Recommended Solutions
Refrigerator
will not operate
J Not connected to an electrical supply - Plug the power cord into a grounded 3 prong outlet. Do not use an
extension cord.
J No power to the electrical outlet - Plug in a lamp to see if the outlet is working.
J Household fuse has blown or circuit breaker has tripped - Replace the fuse or reset the circuit breaker. If the
problem continues, call a licensed electrician.
J New Installation - Following instillation, allow 24 hours for the refrigerator and freezer to cool completely.
NOTE: Adjusting the temperature control(s) to the coldest setting will not cool down either compartment (refrigerator
or freezer) more quickly.
Refrigerator
seems noisy
The compressor in your new refrigerator regulates temperature more efficiently and uses less energy than older models.
During various stages of operation, you may hear normal operating sounds that are unfamiliar.
The following noises are normal:
J Buzzing/Clicking - Heard when the water valve opens and closes to dispense water or fill the ice maker. If the
refrigerator is connected to a water line, this is normal. If the refrigerator is not connected to a water line, turn off
the ice maker.
J Cracking/Crashing - Heard when the ice is ejected from the ice maker mold.
J Popping - Heard when the inside walls contract/expand, especially during initial cool down.
J Pulsating/Whirring - Heard when the fans/compressor adjust to optimize performance during normal operation.
J Rattling - Heard when water passes through the water line, or due to the flow of refrigerant. Rattling may also come
from items placed on top of the refrigerator.
J Water running or gurgling - Heard when ice melts during the defrost cycle and water runs into the drain pan.
J Sizzling - Heard when water drips onto the heater during the defrost cycle.
Motor seems
to run to much
J Your new refrigerator has an energy-efficient motor - The refrigerator may run longer than you’re used to, because
the compressor and fans operate at lower speeds that are more energy-efficient. This is normal.
NOTE: Your refrigerator may run even longer if the room is warm, a large load of food is added, the doors are opened
often, or if a door has been left open.
Temperature is
too warm
J New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool down completely.
J NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either compartment
(refrigerator or freezer) more quickly.
J Doors are opened often or not closed completely - This allows warm air to enter the refrigerator. Minimize door
openings, keep the doors fully closed, and make sure both doors are properly sealed.
J Air vents are blocked - Remove items that are immediately in front of the vents.
J Large amount of warm food recently added - Allow several hours for the refrigerator to return to its normal
temperature.
J Controls are not set correctly for the surrounding conditions - Adjust the controls to a colder setting. Check the
temperature again in 24 hours.
Temperature is
too cold
J Controls are not set correctly for the surrounding conditions - Adjust the controls to a warmer setting. Check the
temperature again in 24 hours.
J Top refrigerator shelf is colder than lower shelves - On some models, air from the freezer enters the refrigerator
compartment through vents near the top refrigerator shelf. As a result, the top shelf can be slightly colder than
lower shelves.
J Air vents are blocked - Remove items that are immediately in front of the vents.
Interior
moisture
buildup
NOTE: Some moisture buildup is normal. Clean with a soft dry cloth.
J Room is humid - A humid environment contributes to moisture buildup. Only use the refrigerator in an indoor location,
with as little humidity as possible.
J Doors are opened often or not closed completely - This allows humid air to enter the refrigerator. Minimize door
openings, keep the doors fully closed, and make sure both doors are properly sealed.
User interface
not responding
J User interface is not responding - Wait 10 seconds, then press any key to change the set point.
J Doors are opened often or not closed completely - To exit Lock mode, press and hold the lock key for 3 seconds.
Loading ...
Loading ...
Loading ...