
Model: GC205/GC205X
20V 12cm
Brushless Pruning Saw
User Manual
CAUTION: Before using this tool, please read this manual completely, and follow all
operating safety measures.

EN 2
Original Instructions
SAFETY & INTERNATIONAL SYMBOLS..........2
SAFETY INSTRUCTIONS....................................3
KNOW YOUR UNIT.............................................8
SPECIFICATIONS.................................................9
ASSEMBLYLY.......................................................9
OPERATION.........................................................11
MAINTENANCE..................................................12
TROUBLESHOOTING........................................14
SAFETY &
INTERNATIONAL
SYMBOLS
Explanation of safety & international
symbols describes safety and international
symbols and pictographs that may appear
on this product. Read the operator’s manual
for complete safety, assembly, operating
and maintenance and repair information.
Caution / Warning.
To reduce the risk of injury,
user must read instruction
manual.
Wear eye protection.
Wear hearing protection.
Wear respiratory protection.
Wear protective gloves.
Do not expose to rain.
DANGER – Keep hands away
from blade.
Avoid power lines, use in dry
conditions.
Keep all bystanders at least
15m (50 ft.) away.
Thrown objects can ricochet
and result in personal injury or
property damage.
Beware of pruning saw
kickback and avoid contact
with bar tip.
Always use pruning saw
twohanded.
Do not dispose of battery
packs in rivers or immerse in
water.
Do not dispose of battery
packs in fire. They will explode
and cause injury.
Use and store the battery at a
temperature below 50° C
(122° F)
Do not disassemble, crush or
expose to heat above 100° C
(212° F); Never expose the
battery to microwaves or high
pressures.
Waste electrical products
should not be disposed of
with household waste. Please
recycle where facilities
exist. Check with your Local
Authority or local store for
recycling advice.
Crossed out dust bin. Batteries
and battery packs should not
be disposed of with household
waste. Please recycle where
facilities exist. Check with
your Local Authority or local
store for recycling advice.
RCM Mark
Guaranteed sound power
level. Noise emission to the
environment according to
the European Community’s
Directive.

3 EN
SAFETY INSTRUCTIONS
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING!
Read all safety warnings, instructions,
illustrations and specifications provided
with this power tool. Failure to follow all
instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for
future reference.
The term "power tool" in the warnings refers
to your mains-operated (corded) power tool
or battery-operated (cordless) power tool.
1. Work Area Safety
a. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.Power
tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control of the tool or
workpiece.
2. Electrical Safety
a. a. Power tool plugs must match the
outlet. Never modify the plug in any
way. Do not use any adapter plugs
with earthed (grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
b. Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if
your body is earthed or grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool
will ncrease the risk of electric shock.
d. Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e. When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable
foroutdoor use reduces the risk of
electric shock.
f. If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of
electric shock.
3. Personal Safety
a. Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment
of inattention while operating power tools
may result in serious personal injury.
b. Use personal protective equipment.
Always wear eye protection. Protective
equipment such as a dust mask, non-
skid safety shoes, hard hat or hearing
protection used for appropriate
conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your
finger on the switch or energizing power
tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench
before turning the power tool on.A
wrench or a key left attached to a
rotating part of the power tool may result
in personal injury.
e. Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose
clothing or jewelry. Keep your hair and
clothing away from moving parts. Loose
clothes, jewelry or long hair can be
caught in moving parts.
g. If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
h. Do not let familiarity gained fromfrequent
use of tools allow you to become
complacent and ignore tool safety
principles. A careless action can cause
severe injury within a fraction of a

EN 4
second.
4. Power Tool Use And Care
a. Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b. Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with
the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power
source and/or remove the battery
pack, if detachable, from the power
tool before making any adjustments,
changing accessories, or storing power
tools. Such preventive safety measures
reduce the risk of starting the power tool
accidentally.
d. Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools and accessories.
Check for misalignment or binding of
moving parts, breakage of parts and
any other condition that may affect the
power tool’s operation. If damaged, have
the power tool repaired before use.
Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to bind
and are easier to control.
g. Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
h. Keep handles and grasping surfaces
dry, clean and free from oil and grease.
Slippery handles and grasping surfaces
do not allow for safe handling and control
of the tool in unexpected situations.
5. Battery Tool Use And Care
a. Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack
may create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c. When battery pack is not in use, keep it
away from other metal objects such as
paper clips, coins, keys, nails, screws or
other small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together
may cause burns or a fire.
d. Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush
with water. If liquid contacts eyes, seek
additional medical help. Liquid ejected
from the battery may cause irritation or
burns.
e. Do not use a battery pack or tool that
is damaged or modified. Damaged
or modified batteries may exhibit
unpredictable behavior resulting in fire,
explosion or risk of injury.
f. Do not expose a battery pack or tool to
fire or excessive temperature. Exposure
to fire or temperature above 100° C
(212° F) may cause explosion.
g. Follow all charging instructions and
do not charge the battery pack or tool
outside the temperature range specified
in the instructions. Charging improperly
or at temperatures outside the specified
range may damage the battery and
increase the risk of fire.
6. Service
a. Have your power tool serviced by
a qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool
is maintained.
b. Never service damaged battery packs.
Service of battery packs should only
be performed by the manufacturer or
authorized service providers.
PRUNING SAW SAFETY
WARNINGS
a. Keep all parts of the body away from
the saw chain while operating the
pruning saw. Before you start the

5 EN
pruning saw, make sure the saw chain
is not contacting anything. A moment of
inattention while operating a pruning saw
may cause entanglement of your clothing
or body with the saw chain.
b. Always hold the pruning saw with your
dominant hand on the main handle, and
your secondary hand on the front brace.
This provides the most support when
making cuts, and will help prevent injury.
c. Hold the pruning saw by insulated
gripping surfaces only, because the saw
chain may contact hidden wiring or its
own cord. Saw chains contacting a "live"
wire may make exposed metal parts of
the saw "live" and could give the operator
an electric shock.
d. Always wear eye protection. Additional
protective equipment for ears, head,
hands, legs and feet are recommended.
Adequate protective equipment will
reduce personal injury from flying debris
or accidental contact with the saw chain.
e. Do not operate a pruning saw while in
a tree, on a ladder, from a rooftop, or
while standing on any unstable surface.
Operation of a pruning saw in this
manner could result in serious personal
injury.
f. Always keep proper footing and operate
the pruning saw only when standing on a
fixed, secure, and level surface. Slippery
or unstable surfaces such as ladders can
cause a loss of balance or control of the
pruning saw.
g. When cutting a limb that is under tension,
be alert for spring back. When tension in
the wood fibers is released, the spring
loaded limb may strike the operator and/
or throw the pruning saw out of control.
h. Use extreme caution when cutting brush
and saplings. The slender material may
catch the saw chain and be whipped
toward you or pull you off balance.
i. Carry the pruning saw by the handle with
the tool switched off and away from
your body. When transporting or storing
the pruning saw, always place the guide
bar cover over the bar and chain. Proper
handling of the pruning saw will reduce
the likelihood of accidental contactwith
the moving saw chain.
j. Follow instructions when lubricating or
tensioning the chain, and when changing
accessories. Improperly tensioned or
lubricated chain could break the pruning
chain.
k. Keep handles dry, clean, and free from
oil and grease. Greasy, oily handles are
slippery and can cause loss of control.
l. Do not use pruning saw for purposes
not outlined in this manual. For cutting
wood only. Do not use pruning saw for
cutting metal, plastic, masonry or non-
wood building materials. Use of the
pruning saw for operations different than
intended could result in a hazardous
situation.
m. Maintain a firm grip, with thumbs and
fingers encircling the handles and both
hands on the pruning saw. Maintaining
control of the pruning saw will reduce
the risk of losing control. Do not let go of
the pruning saw.
n. Do not overreach and do not cut above
shoulder height. This enables better
control of the pruning saw in unexpected
situations.
o. Only use replacement bars and chains
specified by the manufacturer. Incorrect
replacement bars and chains can cause
chain breakage and increase the risk of
injury.
p. Follow the manufacturer’s sharpening
and maintenance instructions for the
pruning saw chain. Decreasing the depth
gauge height can lead to increased risk
of injury.
CAUSES AND OPERATOR
PREVENTION OF KICKBACK
a. Kickback may occur when the nose or
tip of the guide bar touches an object, or
when the wood closes in and pinches the
saw chain in the cut.
b. Tip contact in some cases may cause
a sudden reverse reaction, kicking the
guide bar up and back towards the
operator.
c. Pinching the saw chain along the top of
the guide bar may push the guide bar
rapidly back towards the operator.
d. Either of these reactions may cause you
to lose control of the saw which could
result in serious personal injury. Do not
rely exclusively upon the safety devices
built into your saw. As a chainsaw user,
you should take several steps to keep

EN 6
your cutting jobs free fromaccident or
injury.
e. Kickback is the result of chainsaw misuse
and/or incorrect operating procedures or
conditions and can be avoided by taking
proper precautions as given below:
a. Maintain a firm grip, with thumbs
and fingers encircling the pruning
saw handles and both hands on the
saw. Position your body and arm to
allow you to resist kickback forces.
Kickback forces can be controlled by
the operator if proper precautions are
taken. Do not let go of the pruning
saw.
b. Do not overreach and do not cut above
shoulder height. This helps prevent
unintended tip contact and enables
better control of the pruning saw in
unexpected situations.
c. Only use replacement bars and
chains specified by the manufacturer.
Incorrect replacement guide bars and
saw chains may cause chain breakage
and/or kickback.
d. Follow the manufacturer’s sharpening
and maintenance instructions for the
saw chain. Decreasing the depth gauge
height can lead to increased kickback.
RESIDUAL RISKS
Even with the intended use of the appliance
there will always be a residual risk that
cannot be prevented when using this
tool, even when used properly and for its
intended purpose. Due to the type and
construction of this tool, the following
potential hazards might apply:
• Contact with exposed saw teeth of the
saw chain
• Access to the rotating saw chain
• Unforeseen, abrupt movement of the
guide bar
• Debris from a damaged or broken saw
chain
• Dust and debris flung from the work piece
• Contact with hot chain oil
• Loss of hearing due to lack of ear
protection
SAFETY WARNINGS FOR
BATTERY PACK
a. Do not dismantle, open or otherwise
damage cells or battery pack.
b. Do not short-circuit a battery pack. Do
not store battery packs haphazardly
ina box or drawer where they may
shortcircuit each other or be short-
circuited by conductive materials. When
battery pack is not in use, keep it away
from other metal objects such as paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together
may cause burns or a fire.
c. Do not expose battery pack to heat or
fire. Avoid storage in direct sunlight.
d. Do not subject battery pack to electrical
shock.
e. Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush
with water. If liquid contacts eyes, seek
additional medical help.
f. Seek immediate medical help if a cell or
battery pack has been swallowed.
g. Keep battery pack clean and dry.
h. Wipe the battery pack terminals with a
clean dry cloth if they become dirty.
i. Battery pack needs to be charged before
use. Always refer to this instruction and
use the correct charging procedure.
j. Remove battery pack from charger when
not in use.
k. After extended periods of storage, it may
be necessary to charge and discharge
the battery pack several times to obtain
maximum performance.
l. Battery pack gives its best performance
when it is operated at normal room
temperature (20 ° C ± 5 ° C).
m. When disposing of battery packs, keep
battery packs of different electrochemical
systems separate from each other.
n. Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack
may create a risk of fire when used with
another battery pack.
o. Do not use any battery pack that is not
designed for use with this tool
p. Keep battery pack out of the reach of
children.
q. Retain the original product literature for
future reference.
r. Remove the battery from the tool when

7 EN
not in use.
s. Properly dispose of any damaged or
defective batteries according to local
regulations.
t. Do not remove battery pack from its
original packaging until required for use.
u. Observe the plus (+) and minus (–) marks
on the battery and ensure correct use.
INTENDED USE
• The pruning saw is intended for cutting
only wood and branches up to a diameter
corresponding to the length of the
pruning saw guide bar.
• The pruning saw must be used at ground
level or from a suitable platform that is
completely stable and secure.
• During use, the pruning saw should be
held with a firm grip and with both hands
in the appropriate grip areas.
• The pruning saw is intended for outdoor
use only.
• The pruning saw is not intended for any
use other than those outlined in this
manual.
• Mounting of parts on the pruning
saw is authorized only for original or
manufacturer-approved spare parts (chain
guides or saw chains for example) as well
as for authorized chain guide / saw chain
combinations as indicated in the manual.
• The user is responsible for any
accident resulting from improper use or
unauthorized modification of the pruning
saw.

EN 8
KNOW YOUR UNIT
1 Guide Bar 9 Oil Tank
2 Chain 10 Chain Guard
3 Side Cover 11 Guide Bar Cover
4 Safety Switch 12 Secondary Grip Area
5 Trigger 13 Chain Tensioning Gear
6 Handle 14 Housing Screw
7 ON/OFF Switch 15 Sprocket
8 Oil Tank Cap 16 Chain Tensioning Knob
1
2
3
4
5
6
12
13
14
15
16
11
7
8
9
10

9 EN
SPECIFICATIONS
Model GC205/GC205X*
Input Voltage 18 V (max 20 V)
Rated Output 350 W
No-Load Speed 4500 /min
Chain Speed 8 m/s
Chain Pitch / Gauge 7.6 mm | 1.1 mm
Chain & Bar Length 12 cm
Oil Tank Capacity 45 ml
Weight 1.1 kg
Measured Sound
Power Level LwA
93 dB(A)
K=3 dB(A)
Sound Pressure Level
at Operator's Position
LpA
85 dB(A)
K=3 dB(A)
Guaranteed Sound
Power Level LwA
(measured according
to 2000/14/EC)
96 dB(A)
Valuation of Vibration
3.87 m/s²
K=1.5 m/s²
ASSEMBLY
1. Unpack all parts and lay them on a flat,
stable surface:
2. Remove all packing materials and shipping
devices, if applicable.
3. Package Contents
• Pruning Saw
• Battery Pack
• Charger
• Chainsaw Chain
• Chain Guide Bar
• Guide Bar Cover
• User Manual
NOTE: The actual accessories supplied
may vary depending on the product model,
sales region, production batch, or package
configuration.
4. If you find that parts are missing or show
damage do not use the product but
contact your dealer. Using an incomplete
or damaged product represents a hazard
to people and property.
5. Ensure that you have all the accessories
and tools needed for assembly and
operation. This also includes suitable
personal protective equipment.
INSTALLING THE SAW
CHAIN AND GUIDE BAR
WARNING!
Ensure the battery pack is removed from the
pruning saw before attaching the bar and
chain.
1. Fully loosen the chain tensioning knob
counterclockwise. Then remove the side
cover.
2. Loop the new chain into the slot of the
*20V Max battery, maximum initial battery
voltage (measured without a workload) is
20V. The nominal voltage is 18V.
*X=0-999, A-Z may vary depending on the
sales region or package configuration, with no
safety-related changes between these models.
NOTE: The declared noise emission value(s)
and vibration total value(s) are measured in
accordance with a standard test method, and
may be used both for comparing tools and for
making a preliminary assessment of exposure.
WARNING: The noise and vibration
emissions during actual use of the power tool
may differ from the declared value(s), depending
on how the tool is used. To protect the operator,
hearing protection and gloves should be worn
under actual working conditions.

EN 10
guide bar according to the directions.
3. Twist the chain tensioning gear
counterclockwise. Then fit the guide
bar assembly into the housing screw,
and install the saw chain on the drive
sprocket.
4. Pull the chain around the guide bar with
your gloved hand or using auxiliary tools,
then turn the chain tensioning gear
clockwise to make sure it can run smoothly.
NOTE:
It is still recommended to check for
smoothness of the saw chain before operation,
even after using it for a period of time.
5. Replace the side cover and slightly tighten
the locking knob. Ensure the saw chain
does not slide out of the guide bar.
6. Twist the chain tensioning knob until the
saw chain can be lifted 2-3 mm (1/16" -
1/8") from the center of the guide bar.
7. Fully tighten the chain tensioning knob
clockwise.
NOTE:
Allow the chain to cool after a short period
of use, remove the battery, and check the
tension again.
FILLING OIL
WARNING!
Bar and chain oil prevents premature wear.
Never operate the pruning saw if oil is not
visible. Check oil level frequently and fill as
needed.
Only use lubricants specified or
recommended by the manufacturer to
ensure proper operation and avoid damage.
NOTE:
Bar and chain oil is required to properly
lubricate the guide bar and saw chain. The
pruning saw is equipped with an automatic
oiler that deposits oil on the bar and chain
when running, keeping them properly
lubricated.
1. Place the pruning saw on its side on a
firm, flat surface so that the oil tank cap
is facing upward.
2. Clean any debris from the cap area.Twist
counterclockwise to remove the oil tank
cap.
3. Twist counterclockwise to remove the oil
tank cap.
4. Carefully pour the oil into the tank.
5. Replace the cap and make sure oil is
visible in the tank.
INSTALLING/REMOVING

11 EN
THE BATTERY PACK
WARNING: Use only the accessories
listed below. Using non-approved
accessories may result in poor performance
or safety hazards.
Battery Pack GBA202, GBA204
Charger GCH202, GCH204, GCH206D
NOTE: For usage instructions of the battery
pack and charger, please refer to the
respective user manuals.
To install:
a. Align the ribs on the battery pack with
the mounting slots in the tool.
b. Slide the battery pack in until it clicks into
place.
To remove:
Press the battery-release button on the
battery pack and slide the battery pack out.
OPERATION
WARNING!
• Never operate a pruning saw that is
damaged or improperly adjusted or that is
not completely and securely assembled.
• Be sure that the saw chain stops moving
when the power control system trigger is
released.
• Never adjust the guide bar or saw chain
while the tool is in use.
PRIMING THE OILER
WARNING!
Keep hands, clothing, and hair away from
the drive sprocket when priming the oiler.
NOTE:
• Prime the oiler before the first use or after
being stored for a long time. It is essential
to fill with oil before use. Operating the
pruning saw without bar and chain oil will
result in damage to the pruning saw.
• The chain is automatically lubricated with
oil during operation via the oil outlet.
1. Insert the battery.
2. Place the pruning saw on a firm, flat
surface and run it for approximately two
minutes.
3. Check for an oil spray line coming off the
guide bar and chain.
TENSIONING THE SAW
CHAIN
NOTE:
Check the tension between the saw chain
and the guide bar each time before using
the pruning saw.
WARNING!
Only tension the saw chain when the chain
is cool. A hot chain may contract and
damage the guide bar or chain as it cools.
1. It is not necessary to remove the side
cover to adjust the chain tension.
Simply turn the chain tensioning knob
counterclockwise to increase.
2. Twist the chain tensioning knob until the
chain comes to a suitable tension level.
The correct chain tension is reached when
the saw chain can be lifted by 2-3 mm
(1/16" - 1/8") from the center of the chain
bar.
3. Tighten the chain tensioning knob after
adjustment.
NOTE:
If the chain is still loose when the saw is at
maximum tension, replace the chain.
SWITCHING ON/OFF
1. Press the ON/OFF switch button to unlock
the pruning saw.
2. Set the safety switch button to the "on"
position.
3. Push the trigger to start the tool.
4. Release the trigger and safety switch
button to stop the tool.

EN 12
OVERHEAT PROTECTION
This pruning saw has an overheat protection
function. The tool will automatically shut
down during operation when its internal
temperature reaches an unsafe level. If this
occurs, wait for it to cool down and then
restart the tool.
GENERAL SAWING
TECHNIQUES
NOTE:
It is recommended that first-time user
should, as a basic practice, cut wood using
a sawhorse or cradle.
• Remove lower branches on the tree first.
By doing so, other cut branches can easily
and safely fall to the ground.
• The saw will swing freely once it has fully
passed through the cutting surface. Retain
control of the saw when this occurs, and
remain alert during the entire sawing
operation to prevent risk of injury.
• Only pull the saw out of a cut while the
saw is running. By doing so, you prevent
the chain from jamming in the wood.
• DO NOT saw with the tip of the guide bar.
DO NOT saw into a branch where the tree
branches outwards. This will impede the
tree’s ability to heal.
• When sawing off smaller branches,
place the stopped saw directly on the
branchand engage the trigger. This will
help to prevent unwanted movement at
the beginning of the cut. While applying
light pressure, guide the saw through the
branch from top to bottom.
• When sawing off larger branches, first
make a relief cut. Saw through 1/3 of the
branch diameter from the bottom to top
using the top side of the guide bar. Then
saw from top to bottom for the other 2/3
using the bottom side of the guide bar.
Saw off longer branches in sections in
order to maintain control over the location
of impact.
MAINTENANCE
WARNING!
• Failure to identify and replace damaged
or worn parts can cause serious personal
injury.
• Inspect the pruning saw regularly. Regular
inspection is the first step to proper
maintenance. Follow the guidelines below
to maximize safety and satisfaction.
• Have any damaged or excessively worn
parts replaced immediately.
WARNING!
• Always remove the battery pack and let
the product completely cool down before
performing cleaning and maintenance
work!
• Always wear gloves to reduce the risk of
injury when operating this unit.
• Only perform cleaning and maintenance
work according to these instructions! Any
additional work must be performed by a
qualified specialist!
REPLACING/CHANGING
THE SAW CHAIN AND GUIDE
BAR
Refer to ‘‘INSTALLING THE SAW CHAIN AND
THE GUIDE BAR.’’ Only use replacement
parts approved by manufacturer.
SHARPENING THE CHAIN
Do not sharpen the pruning saw chain
yourself unless you are experienced in doing
so. It is recommended to have the pruning
saw sharpened at an authorized service
location or to replace the chain once it
becomes worn.
CLEANING
• Remove the battery.
• Remove wood chips and other debris from
the battery port. Clean dirty contacts with
a soft, dry cloth. Dirt or oil can cause a

13 EN
poor electrical connection, resulting in
loss of power.
WARNING!
There are no user serviceable parts inside
the battery pack. Do not disassemble.
• After use, clean debris from the pruning
saw and guide bar. Wipe the powerhead
with a clean cloth moistened with a mild
soap solution. Never use harsh cleaners or
solvents.
• Always clean out wood chips, saw dust
and dirt from the bar groove when
replacing saw chain.
• Ensure that the chain tensioning gear is
free of wood chips and other debris.
NOTE:
When cleaning the pruning saw powerhead,
do not immerse in water or other liquids.
TRANSPORTATION
• Remove battery pack from the pruning
saw.
• Install the guide bar cover.
• If desired, drain the bar and chain oil to
reduce seepage.
• Carry saw with bar and chain facing
behind the operator.
Tools can shift during transport. Ensure the
tool is secure and cannot fall or move into
contact with people or property.
STORAGE
• Remove the battery pack from the pruning
saw.
• Clean pruning saw thoroughly as
describedabove.
• Install the guide cover and place an
absorbent pad under the bar.
• Store in a dry place.
• Keep out of reach of children or pets.
• We recommend using the original package
for storage or covering the product with
a suitable cloth or enclosure to protect it
against dust.
NOTE:
To prolong battery life, never store battery
pack in a completely discharged condition.
Make sure the battery pack is charged every
six months or when the LED indicator
shows only one light.
DISPOSAL
Unwanted product should not be disposed
of with household waste. Please recycle
where facilities exist. Check with your local
authority or retailer for recycling advice.
Users should clean up dust generated during
operation to protect environment.
Electrical products should not
be discarded with household
products. Used electrical
products must be collected
separately and disposed of at
collection points provided for
this purpose. Talk with your
local authorities or dealer for
advice on recycling.

EN 14
TROUBLESHOOTING
Suspected malfunctions are often due to causes that users can fix themselves.therefore,
troubleshoot the product using this section. In most cases the problem can be solved quickly
Problem Possible Cause Solution
Motor does
not run
Battery pack is depleted Remove and charge battery pack
Battery pack is not
properly attached
Remove the battery pack from
the product and reattach it
Low cutting
efficiency
Dull / worn chain Sharpen or replace the chain
Dry chain
Check the oil level. Refer to
"FILLING OIL"
Insufficient chain tension
Refer to “TENSIONING THE SAW
CHAIN”
Improper cutting technique Follow guidelines in this manual
Debris in side cover
Remove battery pack, then
remove side cover and clean out
debris.
Chain installed backwards
Refer to “INSTALLING THE SAW
CHAIN AND THE GUIDE BAR”
Product does not
cut properly
Insufficient chain tension
Refer to “TENSIONING THE SAW
CHAIN”
Dull / worn chain Sharpen or replace the chain
Chain installed backwards
Refer to “INSTALLING THE SAW
CHAIN AND THE GUIDE BAR”
Dry chain
Check the oil level. Refer to
"FILLING OIL"
Product suddenly
stops
Battery pack is depleted
Remove and recharge battery
pack
The machine is overloaded
Release the trigger and restart
the machine
Chain and guide
bar overheating
Dry chain
Check the oil level. Refer to
"FILLING OIL

15 EN
WARRANTY POLICY
• During the warranty period, if the product exhibits manufacturing defects (excluding
damage caused by improper use or mishandling), you may contact the MOVA after-sales
service team for support. Upon confirmation of the defect by our technicians, you will be
eligible for complimentary repair or replacement under the warranty terms.
• The warranty is only applicable to the original purchase from an authorized MOVA retailer.
• The warranty period may vary by country/region and is subject to local laws and
regulations.
Warranty period
- Personal and Household Use
• 20V, 40V Garden tools (e.g., lawn mowers, hedge trimmers): 3-year limited warranty from
the date of purchase.
• 20V, 40V Battery system (e.g., chargers, battery packs): 2-year limited warranty from the
date of purchase.
• Maintenance parts/accessories: not covered under the limited warranty.
Professional Use: For commercial, agricultural, and institutional applications: 30-day limited
warranty from the date of purchase.
During the warranty period, the following situationsare not covered under the warranty:
1. Products used for rental purposes.
2. Products whose serial number, factory label, and other identifiers have been torn off or
altered.
3. No valid purchasing document (receipt, invoice, or other) is provided to certify the date
the product was purchased.
4. Maintenance parts/accessories, including but not limited to: lawn mower blades, trimmer
blades, grass bag, mulching insert, grass trimmer head, wheels, brush cutter blade, saw
chain, belts, skid shoes, scraper bar, shear bolts, blower tube nozzles, and other similar
accessories.
5. Defects caused by normal wear and tear or normal product aging. This includes but is
not limited to scratches, dents, paint peeling, or any corrosion or discoloration caused by
overheating, abrasives, and chemical cleaners.
6. Damage caused by:
- Abuse, overloading, misuse, or unauthorized modification.
- Natural disasters, accidents, or other force majeure events.
7. Malfunctions resulting from failure to operate the product according to its instructions,
specifications, or guidelines, or due to improper maintenance, care, or storage.
8. Failures due to the use of unauthorized accessories.
9. Failures caused by repairs made by an unauthorized service center or tampering with the
product by individuals without permission from MOVA.
The warranty covers only the repair of defects specified in these terms. Any other claims
are excluded. Please note: No full unit replacement service will be provided during repairs.
MOVA reserves the right to amend these terms and retains final authority over warranty
interpretation, subject to applicable laws.
For more warranty information, please visit the official website: https://www.mova.tech/
CONTACT US
https://www.mova.tech/pages/contact-us

Manufacturer: Lawnix Technology (Nanjing) Co., Ltd.
Address: Room 501-510, 5/F, Block E (Building 2), No.10 Mozhou East Road, Jiangning
Development Zone, Jiangning District, Nanjing, Jiangsu Province, P.R.China
Made in China
