User manual
Register your product and get support at
www.philips.com/support
Soundbar
6000 Series
TAB6200
2 EN
Contents
1 Important safety instructions 3
Safety 3
Care for your product 4
Care of the environment 4
Declaration of conformity 5
Help and support 5
2 Your Soundbar 6
What’s in the box 6
Soundbar 6
Connectors 7
Wireless subwoofer 7
Remote control 8
Prepare the Remote Control 8
Placement 9
Wall mount 10
3 Connect 11
Dolby Atmos® 11
Connect to HDMI socket 11
Connect to Optical socket 11
Connect to AUX socket 12
Connect to power 12
Pair up with the subwoofer 13
4 Use your soundbar 14
App download 14
Turn on and o 14
Select modes 14
Adjust the Volume 15
Select Equalizer (EQ) Eect 15
LEDs display On/O Indicator 16
DTS Virtual X / Dolby Atmos
virtualiser 16
Auto. volume leveling 16
Play from Bluetooth devices 16
Listen to an external device 17
Play audio through USB 18
Factory reset 18
5 Product specications 19
6 Troubleshooting 20
7 Trademarks 21
3EN
1 Important
safety
instructions
Read and understand all instructions
before you use your product. If damage is
caused by failure to follow instructions, the
warranty does not apply.
Safety
Know these safety symbols
The marking information is located at
the bottom or back of product.
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This is CLASS II apparatus with
double insulation, and no
protective earth provided.
AC voltage
The symbol indicates DC voltage
The symbol indicates polarity of d.c.
power connector
WARNING!
Warning: Risk of electric shock!
The exclamatory mark is intended
to alert the user to the presence of
important operating instructions.
Use only the power supplies
listed in the user manual.
Risk of electric shock or re!
• Before you make or change any
connections, make sure that all
devices are disconnected from the
power outlet.
• Never expose the product and
accessories to rain or water. Never
place liquid containers, such as vases,
near the product. If liquids are spilt on
or into the product, disconnect it from
the power outlet immediately. Contact
Consumer Care to have the product
checked before use.
• Never place the product and
accessories near naked ames or other
heat sources, including direct sunlight.
• Never insert objects into the
ventilation slots or other openings
on the product.
• Where the mains plug or an
appliance coupler is used as the
disconnect device, the disconnect
device shall remain readily operable.
• Battery (battery pack or batteries
installed) shall not be exposed to
excessive heat such as sunshine, re
or the like.
• Disconnect the product from the
power outlet before lightning storms.
• When you disconnect the power cord,
always pull the plug, never the cable.
• Use the product in tropical and/or
moderate climates.
Risk of short circuit or re!
• For identication and supply ratings,
see the type plate at the back or
bottom of the product.
• Before you connect the product to the
power outlet, ensure that the power
voltage matches the value printed on
the back or bottom of the product.
Never connect the product to the
power outlet if the voltage is dierent.
4 EN
Risk of injury or damage to this
product!
• For wall mounting, this product must
be securely attached to the wall in
accordance with the installation
instructions. Use only the supplied
wall mount bracket (if available).
Improper wall mounting may result
in accident, injury or damage. If you
have any query, contact Consumer
Care in your country.
• Never place the product or any
objects on power cords or on other
electrical equipment.
• If the product is transported in
temperatures below 5°C, unpack
the product and wait until its
temperature matches room
temperature before connecting it to
the power outlet.
• Parts of this product can be made
of glass. Handle with care to avoid
injury and damage.
Risk of overheating!
• Never install this product in a
conned space. Always leave a
space of at least four inches around
the product for ventilation. Ensure
curtains or other objects never cover
the ventilation slots on the product.
Battery usage CAUTION
• CAUTION: Danger of explosion if
batteries are incorrectly replaced.
Replace only with the same or
equivalent type.
• Remove batteries if they are
exhausted or if the remote control is
not to be used for a long time.
• Batteries contain chemical
substances, they should be recycled
or disposed of as per state and local
guidelines.
• Install all batteries correctly, + and -
as marked on the apparatus.
• Do not mix old and new batteries.
• Do not mix alkaline, standard
(Carbon-Zinc) or rechargeable (Ni-Cd,
Ni- MH, etc.) batteries.
• The battery (batteries or battery
pack) shall not be exposed to
excessive heat such as sunshine, re
or the like.
• Don’t disposal of a battery into
re or a hot oven, or mechanically
crushing or cutting of a Battery.
• To avoid battery subjected to
extremely low air pressure.
Note
• The rating label is pasted on the bottom or back
of the equipment.
Care for your product
Use only microber cloth to clean the
product.
Care of the environment
Disposal of your old product and
battery
Your product is designed and
manufactured with high quality
materials and components, which
can be recycled and reused.
This symbol on a product means
that the product is covered by
European Directive 2012/19/EU.
This symbol means that the
product contains batteries covered
by European Directive 2013/56/EU
which cannot be disposed of with
normal household waste.
Inform yourself about the local separate
collection system for electrical and
electronic products and batteries.
Follow local rules and never dispose of
5EN
the product and batteries with normal
household waste. Correct disposal
of old products and batteries helps
prevent negative consequences for the
environment and human health.
Removing the disposable batteries
To remove the disposable batteries, see
battery installation section.
Declaration of conformity
This product complies with the radio
interference requirements of the
European community.
Hereby, TP Vision Europe B.V. declares
that the product is in compliance with
the essential requirements and other
relevant provisions of RED Directive
2014/53/EU and UK Radio Equipment
Regulations SI 2017 No 1206. You can
nd the Declaration of Conformity on
www.philips.com/support.
Help and support
For extensive online support, visit
www.philips.com/support to:
• download the user manual and the
quick start guide
• watch video tutorials (available only
for selected models)
• nd answers to frequently answered
questions (FAQs)
• email us a question
• chat with our support representative.
Follow the instructions on the website
to select your language, and then enter
your product model number.
Alternatively, you can contact Consumer
Care in your country. Before you contact,
note down the model number and serial
number of your product. You can nd
this information on the back or bottom
of your product.
6 EN
2 Your Soundbar
Congratulations on your purchase,
and welcome to Philips! To fully
benet from the support that Philips
oers, register your soundbar at
www.philips.com/support.
What’s in the box
Check and identify the items in the
package:
• Soundbar x 1
• Wireless subwoofer x 1
• Remote control x 1
(AAA batteries x 2)
• AC adapter (for soundbar) * x 1
• Power cord (for subwoofer) * x 1
• Wall mount kit x 1
• Quick start guide/
Warranty card / Safety sheet x 1
Soundbar Wall mount kit
(brackets x2 / bracket screws x4 /
Gum Cover x4)
Wireless subwoofer
Remote control
(AAA batteries x 2)
AC adapter *
(for soundbar)
HDMI
HDMI Cable
Quick start guide
Warranty card/Safety sheet
Headphones
s
s
Se
ri
es
C
TN
S
a
f
ety
In
f
o
rma
t
io
n
For EU For UK For AUSFor US
Power Cord *
(for subwoofer)
• Power cord quantity and plug type
vary by regions.
• Images, illustrations and drawings
shown on this User Manual are for
reference only, actual product may
vary in appearance.
Soundbar
This section includes an overview of the
soundbar.
6
4 3 2 1
5
1
(Standby-On)
• Switch the soundbar On or to
Standby.
• Long press for 8 seconds in power
on state to enable or disable Auto-
Standy (15 minutes Auto-Standby).
2
(Source) button
Select an input source for the
Soundbar.
3
(Bluetooth) button
• Press to select the Bluetooth mode.
• Long press for 3 second to enter
the Bluetooth pairing mode.
• Long press for 8 second to
disconnect all devices and clear the
BT connect history list, then enter
pairing mode.
4
/ (Volume) button
Increase or decrease volume.
5
Remote control sensor
6
Soundbar’s LED indicator
LED State Status
HDMI
eARC
Solid White HDMI eARC mode
7EN
BT Solid Blue
Solid White
Bluetooth (Classic) mode
Bluetooth (LE Audio) mode
OPT Solid White OPTCIAL mode
Standby Solid Red Standby mode
USB Solid White USB mode
AUX Solid White AUX mode
Solid White Dolby Atmos
Solid White DTS Audio
Connectors
This section includes an overview of the
connectors available on your soundbar.
6
4 5
1 2 3
1
Optical in socket
Connect to an optical audio output
on the TV or a digital device.
2
DC in socket
Connect to adapter.
3
Audio in socket
Audio input from, for example, an
MP3 player (3.5mm jack).
4
USB
• Connect to a USB storage device for
audio media play.
• Upgrade software of this product.
5
HDMI eARC socket
The port supports the eARC/ARC
HDMI feature, connect to the HDMI
(eARC/ARC) input on the TV.
6
Wall bracket slot
Wireless subwoofer
This section includes an overview of the
wireless subwoofer.
1 2 3
1
AC in ~ socket
Connect to the power supply.
2
Subwoofer indicator
Determine the status based on the
wireless subwoofer indicator.
LED State Status
Fast blink Subwoofer in pairing mode
Solid Connected / Pairing successful
Slow blink Unpaired status
3
Pair button
Press and hold to enter the pairing
mode for the subwoofer, which
is used for manual pairing only.
(Don’t press Pair button as bar
and subwoofer would be paired
automatically after the unit is
switched ON)
8 EN
Remote control
This section includes an overview of the
remote control.
1
(Standby-On)
• Switch the soundbar on or to
standby.
• Long press for 8 seconds in power
on state to enable or disable Auto-
Standy (15 minutes Auto-Standby).
2
(Surround)
Virtualiser ON/OFF.
3
Vol + / Vol - (Soundbar’s Volume)
Increase / decrease the soundbar’s
volume.
4
EQ
• Select Equalizer (EQ) eect.
• Press and hold for 3 second to turn
on/o dialogue enhancement.
5
Treble +/-
Adjust treble level.
6
Bass +/- (Subwoofer’s Volume)
Adjust subwoofer’s volume.
7
(Source)
Press to select an input source for
soundbar.
8
(Mute)
Mute or restore volume.
9
/ (Previous/Next)
Skip to the previous or next track in
USB / BT mode.
10
(Play/Pause)
Start, pause or resume play in USB /
BT mode.
11
AVL
Auto volume leveling ON/OFF and
night mode.
1
2
3
5
6
7
8
9
10
11
4
Prepare the Remote
Control
• The provided Remote Control allows
the unit to be operated from a
distance.
• Even if the Remote Control is
operated within the eective range
19.7 feet (6m), remote control
operation may be impossible if there
are any obstacles between the unit
and the remote control.
• If the Remote Control is operated
near other products which generate
infrared rays, or if other remote
control devices using infra-red rays
are used near the unit, it may operate
incorrectly. Conversely, the other
products may operate incorrectly.
9EN
Replace the Remote Control Battery
1 Press and slide the back cover to
open the battery compartment of
the remote control.
2 Insert two AAA size batteries
(included). Make sure the (+) and (–)
ends of the batteries match the (+)
and (–) ends indicated in the battery
compartment.
3 Close the battery compartment
cover.
Precautions Concerning Batteries
• Be sure to insert the batteries with
correct positive “ ” and negative
“ ” polarities.
• Use batteries of the same type.
Never use different types of batteries
together.
• Either rechargeable or non-
rechargeable batteries can be used.
Refer to the precautions on their
labels.
• Be aware of your fingernails when
removing the battery cover and the
battery.
• Do not drop the remote control.
• Do not allow anything to impact the
remote control.
• Do not spill water or any liquid on
the remote control.
• Do not place the remote control on a
wet object.
• Do not place the remote control
under direct sunlight or near sources
of excessive heat.
• Remove the battery from the remote
control when not in use for a long
period of time, as corrosion or
battery leakage may occur and result
in physical injury, and/or property
damage, and/or fire.
• Do not use any batteries other than
those specified.
• Do not mix new batteries with old
ones.
• Never recharge a battery unless it is
confirmed to be a rechargeable type.
Placement
Place the subwoofer at least 1 meter (3
feet) away from your soundbar, and 10
centimeters away from the wall.
For best results, place your subwoofer as
shown below.
10 EN
Wall mount
Note
• Improper wall mounting may result in accident,
injury or damage. If you have any query, contact
Consumer Care in your country.
• Before wall mounting, make sure the wall can
support the weight of your soundbar.
• Before wall mounting, you need not remove
the rubber feet at the bottom of the soundbar,
otherwise the rubber feet cannot be xed back.
• Depending on the type of wall mounting, make
sure that you use screws of a suitable length
and diameter.
• Please check whether the USB port on the back of
the soundbar is connected to a USB device. If it is
found that the connected USB device affects the
wall-mount, you need to use another USB device
of the appropriate size.
Screw length/diameter
Suggested wall mounting height
You are recommended to install the TV
rst before wall mounting the soundbar.
With a TV preinstalled, wall mount the
soundbar 50mm/2.0’’ in distance from
the bottom of the TV.
WARNING!
• To prevent injury, this apparatus must be securely
attached to the oor/wall in accordance with the
installation instructions.
• Suggested wall mounting height: ≤ 1.5 meters.
1 Drill 4 parallel holes (diameter 3-8mm
each according to wall type) on the
wall.
» The distance between the holes
are: 664mm / 26”
» You can use the wall mount
template provided for helping the
drilling holes position on the wall.
2 Tighten the wall mount brackets on
the wall with screws (included) and
screwdriver (not included). Make
sure that they are securely installed.
3 Lift the unit onto the wall mount
brackets and slot into place.
3
1
~50mm/2.0"
2
664 mm / 26”
48mm
φ4x40
11EN
3 Connect
This section helps you connect your
soundbar to a TV and other devices, and
then set it up.
Note
• For identication and supply ratings, see the
type plate at the back or bottom of the product.
• Before you make or change any connections,
make sure that all devices are disconnected
from the power outlet.
Dolby Atmos®
Dolby Atmos gives you immersive listening
experience by delivering sound in three
dimensional space, and all the richness,
clarity, and power of Dolby sound.
For more information, please visit
dolby.com/technologies/dolby-atmos
Connect to HDMI socket
HDMI eARC (Enhance Audio Return
Channel)
Your soundbar supports HDMI with
eARC/ARC (Enhance Audio Return
Channel). If your TV is HDMI eARC/ARC
compliant, you can hear the TV audio
through your soundbar by using a single
HDMI cable.
HDMI eARC
HDMI eARC
TV
1 On your TV, turn on HDMI-CEC
operations. For details, see the TV
user manual.
• The HDMI ARC connector on the
TV might be labeled dierently.
For details, see the TV user manual.
2 Using a High Speed HDMI cable,
connect the HDMI eARC connector
on your soundbar to the HDMI eARC
connector on the TV.
Note
• Your TV must support the HDMI-CEC and ARC
function. HDMI-CEC and ARC must be set to On.
• The setting method of HDMI-CEC and ARC may
dier depending on the TV. For details about ARC
function, please refer to your TV user manual.
• Make sure to use the HDMI cables can support
the ARC function.
Connect to Optical socket
1 Using an optical cable, connect the
Optical connector on your soundbar
to the Optical out connector on the
TV or other device.
Optical out
Optical in
TV
• The digital optical connector might
be labeled Spdif or Spdif out.
12 EN
Connect to AUX socket
a. Use 3.5mm audio cable
• Use a 3.5mm to 3.5mm audio cable to
connect the TV’s headphone socket to
the Audio in socket on the soundbar.
Headphone
(3.5mm)
Audio out
Audio in
TV
b. Use 3.5mm-RCA audio cable
• Use a RCA to 3.5mm audio cable
to connect the TV’s audio output
sockets to the Audio in socket
on the soundbar.
R
L
Audio out
TV
Audio in
Connect to power
• Before connecting the AC power
cord, ensure you have completed all
other connections.
• Risk of product damage! Ensure that
the power supply voltage corresponds
to the voltage printed on the back or
the underside of the unit.
Conversion plug
Choose the adapter for your region.
If needed, snap on the adapter for your
region.
A B
Soundbar
1 Unwind the mains adapter and
mains cable to their full length.
Connect the mains adapter to the
DC IN 24V socket of the soundbar.
2 Then connect the mains adapter into
a mains socket.
Subwoofer
3 Connect the mains cable to the AC~
socket of the Subwoofer and then
into a mains socket.
• Power cord quantity and plug type
vary by regions.
1
2
3
2
1
AC~
For EU
For EU
or
For UKFor US / For AUS /
For UKFor US / For AUS /
or
A B
or
* Power cord quantity and plug type
vary by regions.
13EN
Pair up with the subwoofer
Tips
• The subwoofer should be within 6 meters, of the
soundbar in an open area.
Automatic pairing
Plug the soundbar and the subwoofer
into the mains sockets and then press
on the unit or remote control to switch
the unit to ON mode. The subwoofer and
soundbar will automatically pair.
» Determine the status based on
the wireless subwoofer indicator.
LED State Status
Fast blink Subwoofer in pairing mode
Solid Connected / Pairing successful
Slow blink Unpaired status
Tips
• Do not press Pair button on the rear of the
subwoofer, except for manual pairing.
Manual pairing
If no audio from the wireless subwoofer
can be heard, manually pair up the
subwoofer.
1 Unplug both the subwoofer and
soundbar from the mains sockets
again, then plug them in again after
3 minutes.
2 Press and hold the Pair button on
the rear of the subwoofer for 3
seconds.
» The indicator on the subwoofer
will rapidly blink.
3 Then press on the soundbar
or remote control to switch the
soundbar ON.
» The indicator on the subwoofer
will become solid when successful.
4 If the indicator still keeps blinking,
repeat step 1-3.
Tips
• The subwoofer should be within 6 m of the
soundbar in an open area (the closer the
better).
• Remove any objects between the subwoofer
and the soundbar.
• If the wireless connection fails again, check if
there is a conict or strong interference (e. g.
interference from an electronic device) around
the location. Remove these conicts or strong
interferences and repeat the above procedures.
14 EN
4 Use your
soundbar
This section helps you use the soundbar
to play audio from connected devices.
Before you start
• Make the necessary connections
described in the quick start guide
and the user manual.
• Switch the soundbar to the correct
source for other devices.
App download
Scan the QR code or search ”Philips
Entertainment” in the Apple App Store
or Google Play to download and install
the app.
Philips Entertainment
Philips Entertainment
With the Philips Entertainment app,
you can set Volume level, Sound Style
(EQ), Dialogue Enhancement, Surround
Sound, Auto. volume leveling, AV sync,
LED Light, Source selection etc.
Turn on and o
• When you rst connect the soundbar
to the main socket, the unit will be in
standby mode.
• Press the button on the remote
control or on the soundbar to switch
the soundbar ON or OFF.
• Disconnect the mains plug from the
mains socket if you want to switch
the soundbar o completely.
Auto Standby
• The soundbar automatically turns
to Standby mode after about 15
minutes if the TV or the external
soundbar is disconnected (or USB,
BT function bit playback pause), or
switched o.
• Long press the button for 8
seconds in power on state to enable
or disable Auto-Standy (15 minutes
Auto-Standby).
Note
• In HDMI (ARC) mode will enter network
standby mode after approx. 15 minutes, if it has
no audio playback.
• In Aux in, USB, Optical and Bluetooth mode,
the unit will automatically go to Standby mode
approx 15 minutes, if it has no audio playback.
• When the EUT is no audio signal operated
under Aux in, USB, Optical and Bluetooth
mode, the unit entered standby mode within
20minutes
• The EUT operated on “Networked standby
mode” when the equipment under HDMI (ARC)
mode and cutting o play signal via TV remote
control during the equipment work normally.
Select modes
Press the (Source) button repeatedly on
the soundbar or on the remote control to
select the HDMI eARC, BT, BT (LE Audio),
OPT, USB, AUX mode.
15EN
» Switch the playback source and
the front indicator lights up
accordingly.
Adjust the Volume
Adjust the Soundbar’s Volume
• Press Vol+/Vol- (Volume) to increase
or decrease a volume level.
» When adjusting the volume, the
indicator will increase / decrease
the amount of light. According
to the corresponding light display
/ blinking (Fig), determine the
current volume level.
Entertainment
< 90%
< 100%
< 77%
< 64%
< 51%
< 38%
< 25%
< 12%
Music
Original
Dialogue
• To mute sound, press (Mute).
• To restore the sound, press (Mute)
again or press Vol+/Vol- (Volume).
Adjust the Subwoofer’s Volume
• Press Bass +/- (subwoofer) to
increase or decrease the subwoofer’s
volume level.
Adjust Treble level
• Press the Treble +/- button to change
the high frequency (treble).
Bass/Treble LED State
+5 ● ●●●●◎● ●
+4 ● ●●●◎●●●
+3 ● ●●◎●●●●
+2 ● ●◎●●●●●
+1 ● ◎ ●●●●●●
0 ● ●●●●●●●
-1 ● ●●●●●◎ ●
-2 ● ●●●●◎ ● ●
-3 ● ●●●◎ ●●●
-4 ● ●●◎ ●●●●
-5 ● ● ◎ ●●●●●
Select Equalizer (EQ)
Eect
Select predened sound modes to suit
your video or music.
1 Press the EQ button on the remote
control to select your desired preset
equalizer eects.
» All LEDs lights up for 0.5 second
to indicate entering EQ selection
menu.
2 Press the EQ button to switch among
the modes.
» Light up LEDs for 3 second to
show current EQ mode according
to the EQ mode denition.
Entertainment
< 90%
< 100%
< 77%
< 64%
< 51%
< 38%
< 25%
< 12%
Music
Original
Dialogue
16 EN
LEDs display On/O
Indicator
Press and hold (Mute) button on the
remote control for 5 second will enable/
disable LEDs display.
» OFF: The LEDs brightness will
return normal once you press any
button. LEDs should be turned
o automatically after idling for
10 second.
» ON: The LEDs brightness will not
self-extinguish.
Tips
• During standby, the Standby LED shall turn on
regardless LEDs display OFF setting.
DTS Virtual X / Dolby
Atmos virtualiser
DTS Virtual:X / Dolby Atmos virtualiser
allows you to enjoy multi-dimensional
sound regardless of room size, layout, or
speaker conguration.
DTS Virtual:X technology features
DTS’s proprietary virtual height and
virtual surround processing to deliver
an immersive sound experience from
any type of input source and speaker
conguration.
Press the button on the remote control
to enable or disable virtual on.
Status
LED State
ON
●●●●●●●● ( )
(Two center LEDs spread out to right/left)
OFF
●●●●●●●● ( )
(left / right LEDs close to the center)
• ON: This mode uses DTS Virtual:X
with virtual height and virtual
surround processing to realize a
three-dimensional sound eld when
the height speakers are not used.
• OFF: Do not use “DTS Virtual:X” .
Auto. volume leveling
Press the AVL button to switch Auto
volume leveling ON/OFF or night mode.
Status
LED State
OFF ●●●●●●●●
ON ● ● ●●●●● ●
NIGHT ● ●●●●●●●
• OFF: Do not use “Auto volume” .
• ON: Responds in real time to
dierent sources and types of
content to maintain consistent
loudness.
• NIGHT: Maintain even loudness
for all sources and types of
content, and enhanced vocal and
dialogue to make it easier to hear
in a quite listing environment.
Play from Bluetooth
devices
Through Bluetooth, connect the
soundbar with your Bluetooth device
(such as an iPad, iPhone, iPod touch,
Android phone, or laptop), and then you
can listen to the audio les stored on the
device through your soundbar speakers.
1 Press the button on the soundbar
or (Source) on the remote control
to select the BT (Bluetooth) mode.
» The BT indicator will blink blue.
2 On the Bluetooth device, switch
on Bluetooth, search for and select
Philips TAB6200 to start connection
(see the user manual of the Bluetooth
device on how to enable Bluetooth).
17EN
» During connection, the BT
indicator will blink blue.
3 Wait until you hear voice prompt
from the soundbar.
» If the successfully connected, the
BT indicator will light up solidly
blue.
4 Select and play audio les or music
on your Bluetooth device.
• During play, if a call is coming,
music play is paused. Play
resumes when the call ends.
• If your Bluetooth device supports
AVRCP prole, on the remote
control you can press /
to skip to a track, or press to
pause/resume play.
If your mobile phone supports LE
Audio, you can experience and
enjoy this new feature.
1 Press the button on the soundbar
or (Source) on the remote control
to select the BT (LE Audio) mode.
» The BT indicator will blink white.
2 On the LE Audio device, open
settings and switch on Bluetooth
(Ensure the LE Audio function is
activated on your LE Audio device),
search for and select Philips
TAB6200-LEA to start connection.
LED Status Name
Blue BT Philips TAB6200
White BT (LE Audio) Philips TAB6200-LEA
To exit Bluetooth, you can:
• Switch the unit to another source.
• Disable the function from your
Bluetooth device. Or place your
Bluetooth device out of the maximum
operational range. The Bluetooth
device will be disconnected from the
unit after the voice prompt.
• Press and hold the button on the
soundbar.
Note
• In an open space without obstructions.
The maximum operational range between
the soundbar and a Bluetooth device is
approximately 10 meters (30 feet).
• Compatibility with all Bluetooth devices is not
guaranteed.
• The music streaming may be interrupted by
obstacles between the device and soundbar,
such as wall, metallic casing that covers the
device, or other devices nearby that operate in
the same frequency.
Listen to an external device
Ensure that the soundbar is connected to
the TV or audio device.
1 Press the (Source) button repeatedly
on the soundbar or on the remote
control to select the HDMI eARC, OPT,
AUX mode.
» The indicator light on the
soundbar will show which mode is
currently in use.
2 Operate your audio device directly
for playback features.
3 Press the +/- (Volume) buttons to
adjust the volume to your desired
level.
Note
• While in OPTICAL/HDMI ARC mode, if there’s
no sound output from the unit, you may need
to activate PCM or Dolby Digital Signal output
on your source device (e.g. TV, DVD or Blu-ray
player).
18 EN
Play audio through USB
Enjoy audio on a USB storage device,
such as an MP3 player and USB ash
memory, etc.
1 Insert the USB device.
2 Press the (Source) button repeatedly
on the soundbar or on the remote
control to select the USB mode.
3 During playback:
Button Action
Start, pause or resume play
Skip to the previous track
Skip to the next track
Note
• This product may not be compatible with
certain types of USB storage devices.
• If you use a USB extension cable, USB hub,
or USB multifunctional card reader, the USB
storage device may not be recognized.
• Do not remove the USB storage device while
reading les.
• The system can support USB devices with up to
128 GB of memory.
• This system can play MP3/WAV/FLAC.
• Support a USB port: 5V 500mA.
Factory reset
Reset device to default setting.
• Turn on the soundbar, press and hold
the and buttons at the same
time for 8 seconds.
» All LEDs light up for 5 seconds,
standby LED in Red.
Item Default settings
EQ Movie
Master Volume 10
Subwoofer Volume
0
Treble 0
Surround OFF
Auto Volume OFF
Night OFF
Source HDMI-ARC
BT pairing info Clear
AV SYNC 0
DISPLAY ON
Auto Standby (Auto
Power Down)
ON
Dialogue
enhancement
OFF
19EN
5 Product
specifications
Note
• Specications and design are subject to
change without notice.
Bluetooth / Wireless
Bluetooth proles A2DP, AVRCP
Bluetooth version V 5.3
Bluetooth frequency
range / Transmitter
power (EIRP)
2402 ~ 2480MHz
< 10dBm
2.4G wireless frequency
range / Transmitter
power (EIRP)
2402 ~ 2480MHz
< 10dBm
Amplier Section
Total
RMS 120W @THD < =10%
Max. 240W
Soundbar
Power supply DC 24V 1.5A
AC Adapter (for Main Unit)
Model:
KA3601A-2401500DE
(Interchangeable 3
Pin BS 1363-1 and 2
pin (EN 50075)
Input:
100-240V~ 50/60Hz
1.0A Max
Output:
24V 1.5A
Power
consumption
36 W
Standby power
consumption
Standard standby
mode < 0.50 W
Networked standby
mode < 2.0 W
Frequency
response
180Hz - 20KHz
Speakers
impedance
8Ω x 4
USB direct version 2.0 Full Speed
USB 5V 500mA
Dimension
(W x H x D )
811 x 37 x 42 mm
Weight 0.61 kg
Operating
temperature
0°C - 40°C
Subwoofer
Power supply 100-240V~
50/60 Hz
Power consumption 20 W
Standby consumption < 0.50 W
Frequency response 40Hz - 150Hz
Impedance 4 Ω
Dimensions
(W x H x D)
195 x 315.5 x
195 mm
Weight 3.03 kg
Operating temperature 0°C - 40°C
Remote control
Distance/Angle 6m/30°
Battery type AAA (1.5V X 2)
Supported audio formats
HDMI
eARC
LPCM 2ch, LPCM 5.1ch, LPCM
7.1ch, Dolby Digital, Dolby Digital
plus, Dolby True HD, Dolby MAT,
Dolby Atmos - Dolby Digital Plus,
Dolby Atmos - TrueHD, Dolby
Atmos - Dolby MAT, DTS Digital
surround 5.1
HDMI ARC
LPCM 2ch, LPCM 5.1ch, Dolby
Digital, Dolby Digital plus, Dolby
Atmos - Dolby Digital Plus, DTS
Digital surround 5.1
Optical
LPCM 2ch, LPCM 5.1ch, Dolby
Digital, DTS Digital surround 5.1
Bluetooth
SBC
USB
MP3 / WAV / FLAC
20 EN
6 Troubleshooting
Warning
• Risk of electric shock. Never remove the
casing of the product.
To keep the warranty valid, never try to
repair the product yourself.
If you have problems using this product,
check the following points before you
request service. If you still have a problem,
get support at www.philips.com/support.
Main unit
The buttons on the main unit do not
work.
• Disconnect form the power supply for a
few minutes, then connect again.
No power
• Ensure that the AC cord is properly
connected.
• Ensure that there is power at the AC
outlet.
• Press button on the remote control or
soundbar to turn the soundbar on.
Sound
No sound from the soundbar speaker.
• Connect the audio cable from your
soundbar to your TV or other devices.
However, you do not need a separate
audio connection when:
- the soundbar and TV are connected
through HDMl ARC connection, or
- a device is connected to the HDMI in
connector on your soundbar.
• On the remote control, select the
correct audio input.
• Make sure that the soundbar is not
muted.
Distorted sound or echo.
• If you play audio from TV through
this product, make sure that the TV is
muted.
No sound from the wireless subwoofer.
• Manually connect the subwoofer to
the main unit.
• Increase the volume. Press + (Volume
Up) on the remote control or on the
soundbar.
• When using either of the digital input,
if there is no audio:
- Try setting the TV output to PCM or
- Connect directly to your Blu-ray/
other sources.
- Some TVs do not pass through digital
audio.
• Your TV may be set to variable audio
output. Conrm that the audio output
setting is set to FIXED or STANDARD,
not VARIABLE. Refer to your TV’s user
manual for more detailed information.
• If using Bluetooth, ensure that the
volume on your source device is turned
up and that the device is not muted.
Bluetooth
A device cannot connect with the
soundbar.
• The device does not support the
compatible proles required for the
soundbar.
• You have not enabled the Bluetooth
function of the device. See the user
manual of the device on how to enable
the function.
• The device is not correctly connected.
Connect the device correctly.
• The soundbar is already connected
with another Bluetooth device.
Disconnect the connected device,
and then try again.
21EN
Quality of audio play from a connected
Bluetooth device is poor.
• The Bluetooth reception is poor. Move
the device closer to the soundbar, or
remove any obstacle between the
device and the soundbar.
I can’t nd the Bluetooth name of this
unit on my Bluetooth device.
• Ensure the Bluetooth function is
activated on your Bluetooth device.
• Re-pair the unit with your Bluetooth
device.
Remote control does not work
• Before you press any playback control
button, rst select the correct source.
• Reduce the distance between the
remote control and the unit.
• Insert the battery with its polarities (+/-)
aligned as indicated.
• Replace the battery.
• Aim the remote control directly at the
sensor on the front of the unit.
The subwoofer is idle or the indicator
of subwoofer does not light up
• Unplug power cord from the mains
socket, and plug it in again after 3
minutes to reset the subwoofer.
7 Trademarks
The Adopted Trademarks HDMI, HDMI High-
Denition Multimedia Interface, HDMI trade
dress and the HDMI Logos are trademarks
or registered trademarks of HDMI Licensing
Administrator, Inc. in the United States and
other countries.
Dolby, Dolby Atmos, and the double-D symbol
are registered trademarks of Dolby Laboratories
Licensing Corporation. Manufactured under
license from Dolby Laboratories. Condential
unpublished works. Copyright © 2012–2024
Dolby Laboratories.All rights reserved.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by MMD Hong
Kong Holding Limited is under license. Other
trademarks and trade names are those of their
respective owners.
FOR DTS PATENTS, SEE HTTP://XPERI.COM/
DTS-PATENTS/. MANUFACTURED UNDER
LICENSE FROM DTS, INC. AND ITS AFFILIATES.
DTS, THE DTS LOGO, DIGITAL SURROUND,
VIRTUAL:X, AND THE DTS VIRTUAL:X LOGO ARE
REGISTERED TRADEMARKS OR TRADEMARKS
OF DTS, INC. AND ITS AFFILIATES IN THE UNITED
STATES AND/OR OTHER COUNTRIES. © DTS,
INC. AND ITS AFFILIATES.ALL RIGHTS RESERVED.
If you have a Roku TV™ model, setup is easy.
Just use a cable to connect your soundbar to
the HDMI ARC port on your TV and follow the
on-screen instructions.
Roku, the Roku logo, Roku TV, Roku TV Ready,
and the Roku TV Ready logo are trademarks
and/or registered trademarks of Roku, Inc.
22 EN
FCC information
NOTE: This equipment has been tested
and found to comply with the limits
for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio
or television reception, which can be
determined by turning the equipment
o and on, the user is encouraged to
try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an
outlet on a circuit dierent from that
to which the receiver is connected.
• Consult the dealer or an experienced
radio / TV technician for help.
FCC&IC Warning:
• This equipment should be installed
and operated with minimum
distance 20cm between the radiator
& your body.
• Changes or modications to this unit
not expressly approved by the party
responsible for compliance could
void the user’s authority to operate
the equipment.
FCC & IC Attention
• Cet appareil est conforme à FCC et
IC l’exposition aux rayonnements
limites xées pour un environnement
non contrôlé. Cet appareil doit être
installé et utilisé avec une distance
minimale de 20 cm entre le radiateur
et votre corps. Cet transmetteur ne
doit pas être co-situé ou opérant en
liaison avec toute autre antenne ou
transmetteur.
• Des câbles blindés doivent être
utilisés avec cet apparei l pour
assurer la conformité avec les
limites de la classe B de la FCC.
fonctionnement de I’appareil.
IC-Canada:
CAN ICES (B)/NMB(B)
This device contains licence-exempt
transmitter(s) / receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the
following two conditions:
1 This device may not cause
interference.
2 This device must accept any
interference, including interference
that may cause undesired operation
of the device.
Avis d’Industrie Canada:
CAN ICES (B)/NMB (B)
L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences
et Développement économique Canada
applicables aux appareils radio exempts
de licence. L’exploitation est autorisée
aux deux conditions suivantes :
1 L’appareil ne doit pas produire de
brouillage;
2 L’appareil doit accepter tout
brouillage radioélectrique
subi, même si le brouillage est
susceptible d’en compromettre le
fonctionnement.
Specications are subject to change without notice. Please visit
www.Philips.com/support for the latest updates and documents.
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license.
This product has been manufactured by and is sold under the responsibility
of MMD Hong Kong Holding Limited or one of its aliates, and MMD Hong
Kong Holding Limited is the warrantor in relation to this product.
TAB6200_UM_EN_V4_250425
