Mova LIDAX ULTRA 2000 AWD LiDAX Ultra AWD Robot Lawn Mower Wire Free RTK Free

Product's Documents

Below are documents related to this product, you can read online or download:
LIDAX ULTRA 2000 AWD photo

User Manual

This is the main product document for model LIDAX ULTRA 2000 AWD.

The file format is pdf, 41 pages, you can download this manual here .

background
EN
4
1 Safety Instructions ��������������������������������������������������������������������������������������P05
2 Product Introduction ����������������������������������������������������������������������������������P09
3 Installation ����������������������������������������������������������������������������������������������������P13
4 Preparation for First Use ��������������������������������������������������������������������������� P16
5 Map Your Garden �����������������������������������������������������������������������������������������P21
6 Operation ����������������������������������������������������������������������������������������������������� P27
7 MOVAhome App �������������������������������������������������������������������������������������������P31
8 Maintenance ������������������������������������������������������������������������������������������������ P33
9 Battery ��������������������������������������������������������������������������������������������������������� P37
10 Winter Storage ������������������������������������������������������������������������������������������ P37
11 Transport ���������������������������������������������������������������������������������������������������� P37
12 Troubleshooting �����������������������������������������������������������������������������������������P38
13 Specifications �������������������������������������������������������������������������������������������� P43
Table of Contents
background
EN
5
1.1 General Safety Instructions
1 Safety Instructions
• Carefully read and understand the user manual before using the product.
• Only use the equipment recommended by MOVA with the product. Any other usage is incorrect.
• Do not allow children to be in the vicinity or play with the machine when it is operating.
• Do not use the product in areas where people are unaware of its presence.
• When manually operating the product with the MOVAhome app, do not run. Always walk,
watch your steps on slopes, and maintain balance at all times.
• Avoid using the product when there are people, especially children or animals, in the work area.
• Avoid using the machine and its peripherals in bad weather conditions, especially when
there is a risk of lightning.
• If operating the product in public areas, place warning signs around the work area with
the following text: "Warning! Automatic lawn mower! Keep away from the machine!
Supervise children!"
• Wear sturdy footwear and long trousers when operating the product.
• To prevent damage to the product and accidents involving vehicles and individuals, do not
set work areas or transport paths across public pathways.
• Do not touch moving hazardous parts, such as the blade disc, before it has come to a
complete stop.
• Seek medical aid in case of injury or accident.
• Set the product OFF before clearing blockages, performing maintenance, or examining the
product. If the product vibrates abnormally, inspect it for damage before restarting. Do not
use the product if any parts are defective.
• Do not install the main cable in areas where the product will cut. Follow the instructions
provided for cable installation.
• Only use the charging station included in the package to charge the product. Incorrect use
may result in electric shock, overheating, or corrosive liquid leakage from the battery. In
case of electrolyte leakage, flush with water/neutralizing agent and seek medical aid if the
corrosive liquid comes into contact with your eyes.
• When connecting the main cable to the power outlet, use a residual-current device (RCD)
with a maximum tripping current of 30 mA.
• Only use original batteries recommended by MOVA. The safety of the product cannot be
guaranteed with non-original batteries. Do not use non-rechargeable batteries.
• Keep any supply and/or extension cords away from the working area to avoid damage
to the cords which can lead to contact with live parts.
• The illustrations used in this document are for reference only. Please refer to the
actual products.
• Never allow children, persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge or people unfamiliar with these instructions to use the
machine, local regulations may restrict the age of the operator.
• Do not connect or touch a damaged cable until it is disconnected from the power outlet. If
the cable becomes damaged during operation, disconnect the plug from the power outlet.
A worn or damaged cable increases the risk of electrical shock and should be replaced by
service personnel.
• Do not push the product forcefully or quickly, as this may damage the product.
• To maintain compliance with the RF exposure requirement, a separation distance of 35 cm
(13.8") between the device and the human should be maintained.
• WARNING: For the purposes of recharging the battery, only use the detachable supply unit
provided with this appliance.
background
EN
6
• Keep your hands and feet away from the rotating blades. Do not place your hands or feet
near or below the product when it is turned on.
• Do not lift or move the product when it is turned on.
• Park the robot at the charging station or turn it OFF when there are people, especially
children or animals, in the work area.
• Ensure that there are no objects such as stones, branches, tools, or toys on the lawn.
Otherwise, the blades may be damaged when they come into contact with an object.
• Do not put objects on top of the product or charging station.
• Do not use the product if the STOP button is not functioning.
• Avoid collisions between the product and people or animals. If a person or animal comes in
the path of the product, stop it immediately.
• Always set the product OFF when it is not in operation.
• Do not use the product simultaneously with a pop-up sprinkler. Utilize the Schedule
function to ensure that the product and pop-up sprinkler do not operate at the same time.
• Avoid placing a connection channel where pop-up sprinklers are installed.
• Do not operate the product in the presence of standing water in the work area, such as
during heavy rain or water pooling.
• Do not place the robot upside down.
• Set the product OFF when performing maintenance.
• After washing, ensure that the product is placed on the ground in its normal orientation,
not upside down.
• Do not reverse the product to clean the chassis. This precaution is necessary to prevent
water from entering the motor and potentially affecting normal operation.
• Disconnect the plug from the charging station or operate the disabling device before
cleaning or performing maintenance on the charging station.
• Do not use a high-pressure washer or solvents to clean the product.
Lithium-ion batteries can explode or cause a fire if disassembled, short-circuited, exposed
to water, fire, or high temperatures. Handle them with care, do not dismantle or open the
battery, and avoid any form of electrical/mechanical abuse. Store them away from direct
sunlight.
• Only use the battery charger and power supply provided by the Manufacturer. The use of
an inappropriate charger and power supply can cause electric shocks and/or overheating.
• DO NOT ATTEMPT TO REPAIR OR MODIFY BATTERIES! Repair attempts may result in
severe personal injury, due to explosion or electrical shock. If a leak develops, released
electrolytes are corrosive and toxic.
• This appliance contains batteries that can only be replaced by skilled persons.
To avoid injuries, wear protective gloves when replacing the blades.
1.3 Safety Instructions for Operation
1.4 Safety Instructions for Maintenance
1.5 Battery Safety
1.6 Residual Risks
• Avoid installing the charging station in areas where people may trip over it.
• Do not install the charging station in areas where there is a risk of standing water.
• Do not install the charging station, including any accessories, within 60 cm (23.6") of any
combustible material. Malfunctioning or overheating of the charging station and power
supply can pose a fire hazard.
1.2 Safety Instructions for Installation
background
EN
7
1.7 Symbols and Decals
WARNING –
Read user instructions before operating the machine.
WARNING –
Keep a safe distance from the machine when operating.
WARNING –
Operate the disabling device before working on or lifting the machine.
WARNING –
Do not ride on the machine.
WARNING –
It is not permitted to dispose of this product as normal household
waste. Ensure that the product is recycled in accordance with local
legal requirements.
WARNING –
Keep your hands and feet away from this area when the blade disc is in the
offset mowing position. Contact with the blades could cause serious injury.
background
EN
8
The garden product is intended for domestic lawn mowing. It is designed to mow often,
maintaining a healthier and better-looking lawn than ever before. Depending on the size of your
lawn, your mower may be programmed to operate at any time or frequency. It is impossible for
digging, sweeping, or snow cleaning.
Hereby, Kutting Technology (Suzhou) Co., Ltd. declares that the radio equipment model
MXXM7100/MXXM7101/MXXM7102 Lawnmower is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
https://www.mova.tech/pages/declaration-of-conformity.
The product is in compliance with UK PSTI regulations; the full text of the declaration of
conformity is available at the following internet address: https://www.mova.tech/pages/
statement-of-compliance-for-uk-psti.
For the detailed e-manual, please go to https://www.mova.tech/pages/user-manuals-and-faqs.
This product conforms to the applicable EU Directives.
Class Ⅲ
Before charging, read the instructions.
Direct current
Class Ⅱ
INTENDED USE
background
EN
9
2 Product Introduction
11
Lint-free cloth
12
Quick start guide
1
LiDAR protective cover
2
The robot
3
Charging tower
(with a 10 m (32.8 ft) extension cable)
4
Baseplate
5
Power supply
6
Cleaning brush
7
Stakes x 8, Hex key
8
Spare blades and screws × 36
9
Screwdriver
10
User manual
1
2
3
4
5 6
8 97
10
11
12
2.1 What's in the Box
background
EN
10
Stereo vision camera²
Charging contacts
LiDAR¹
Top cover
Display
Knob
Stop button
Rain sensor
2.2 Product Overview
1: The LiDAR helps obtain environmental information and facilitates the robot's positioning,
obstacle avoidance and sensing of water and dirt. Based on MOVA's lab testing, the
detection range (at 100 klx) is 30 m (98.4 ft) at 10% reflectivity and 70 m (229.7 ft) at 80%
reflectivity. The field of view is 360° .
2: The stereo vision camera detects obstacles, lawn boundaries, and human presence. The
angle of view is 120° (horizontal), 75° (vertical), 120° (diagonal). The resolution is 2 MP.
Battery compartment
Handle
UltraTrim ™ blade disc
Rear wheel
Airtag compartment
Rear indicator light
Omni wheel
background
EN
11
2.3 Introduction to Link Service
Rear Indicator Light
The Link Service provides 4G cellular connectivity and GPS functionality.
• The 4G network connectivity allows you to remotely monitor your robot's status and initiate
mowing tasks without a Wi-Fi connection.
• The built-in GPS allows you to track the robot’s real-time location in Google Maps via the
app and receive notifications if it moves outside the designated map area.
Color Meaning
Solid red The robot works normally or is on standby.
Breathing red The robot is charging in the charging station.
Flowing red
The robot is in offset-mowing mode with its blade disc
shifted sideways for cleaner edge cutting.
High-frequency blinking
red
An error has occurred.
The Link Service activates automatically when you power on your robot. You'll see the
illuminated on both the robot's display and in the app, con󶀄rming successful activation. To
check the Link Service status and expiration date, go to Device Page >
> Connections >
Link Service.
Link Service is o󶀃ered free of charge for a period speci󶀄ed in the Specifications section,
starting from the time of activation. To extend the service upon expiration, please contact
the MOVA after-sales service team.
Note:
• The Link Service will be locked if the Link Service is not renewed within three months after
expiration. To reactivate the service, please contact the MOVA after-sales service team.
Reactivation may incur fees.
• The Link Service is designed exclusively to be used with MOVA lawnmowers. Any abnormal
status detected in the Link Service may result in the suspension of your service. If this
occurs, please contact the MOVA after-sales service team to help you restore the service.
Activate the Link Service
background
EN
12
2s
1
Turn off the robot.
2
Cover the LiDAR with its protective cover.
3
Place the robot on its side and lean
it securely against a wall. Ensure that
the display, camera, and LiDAR are not
pressed against any surface.
4
Press the buckle to remove the AirTag
holder.
5
Insert the AirTag into the holder or
take the AirTag out of the holder.
6
Reinstall the holder.
Note:
AirTag is not included. Please prepare your own.
To install or remove AirTags:
The airtag compartment supports Airtag or other tracking devices that help you locate and
track your robot.
2.4 Introduction to Airtag Compartment
background
EN
14
2
Secure the baseplate to the ground with the supplied stakes and hex key.
3
Insert the cleaning brush into the charging tower by aligning the tab with the slot.
4
Connect the power supply to the extension cable and then connect to a power outlet.
Please keep the power supply at least 30 cm (11.8") above the ground.
Note: The LED indicator on the charging station will be constant blue when there is power.
background
EN
15
5
Remove the LiDAR protective cover.
LED Indicator on the Charging Station
LED Indicator Light Colour Meaning
Blinking/solid red
1. There is an issue with the charging station (such as a
problem with the charging current or voltage).
2. The robot docks in the charging station but the charging
is abnormal (for example charging contacts have a short
circuit).
Solid blue
The charging station has power. The robot is not in the
charging station.
Breathing green The robot is charging in the charging station.
Solid green
The robot docks at the charging station and is either:
1. Fully charged, or
2. Not charging because the current time is outside the
designated charging period.
6
Put the robot in the charging station to charge. Make sure the charging contacts on the
robot and the charging station are connected correctly.
Note:
•
The indicator light will breathe in green when the robot is charging successfully in the
charging station.
•
If you're looking to add a garage for extra protection, please use the matching MOVA
Garage available at local stores or online. Using a non-MOVA garage may cause issues
during recharging.
background
EN
16
Display
Icon Status
Battery level (Shows the current battery level.)
Charging (The robot successfully docks in the charging station.)
Bluetooth (The robot is connected to the app via Bluetooth.)
Wi-Fi (The robot is connected to the app via a Wi-Fi network.)
Link service (Link service is activated.)
Schedule (A task is scheduled for today and has not started yet.)
Power on/o
Display
Back
Start
Knob
Home
4 Preparation for First Use
The control panel inside the top cover o󶀃ers the following features.
•
Modes: Switch between All-area mowing and edge mowing.
•
Schedule: View and turn on/o󶀃 the "Spr/Sum Schedule" and "Aut/Win Schedule".
•
Settings: Access the mowing con󶀄gurations such as mowing e󶀆ciency, mowing height,
obstacle avoidance height, and rain/frost protection. Also, you can manage the robot
con󶀄gurations, including PIN code, volume, language, etc.
Note: The features might be updated depending on the software version.
4.1 Get Familiar with the Control Panel
background
EN
17
Buttons
Button Function
Power
Press and hold for 2 seconds to turn the robot on.
To turn o󶀃 the robot, ensure it is outside the charging station. Press
and hold for 2 seconds, then enter the PIN code to con󶀄rm.
Start
To start all-area mowing or resume paused tasks, press the button,
and close the robot's top cover to con󶀄rm.
Home
To send the robot back to the charging station to charge, press the
button, and close the robot's top cover to con󶀄rm.
Back
To navigate up one level in the menu, press the button.
Knob
To con󶀄rm the selection in the menus, press the knob.
To enable Bluetooth pairing mode, press and hold the knob for 3
seconds.
To navigate through the menu, turn the knob clockwise/anticlockwise.
Start + Back
To factory reset the robot, press and hold the
button and the
button together for 3 seconds.
Home + Back
Press and hold the
button and button together for 3 seconds to
enter the About page in Settings. The About page will disappear within 5
seconds.
Stop
Press the Stop button to stop the robot. PIN code must be entered on the
control panel to resume the operation.
Complete the basic settings before the robot is ready to start working.
1
Open the robot's top cover.
4.2 Initial Settings
4.2.1 Set Language & PIN Code
background
EN
18
Note:
The robot will automatically turn on when it docks in the charging station.
2
Press and hold the
button on the control panel for 2 seconds to turn on the robot.
3
Select the Language You Prefer
Turn the knob clockwise to go down and anticlockwise to go up to select your language.
Press the knob to confirm.
2s
4
Set PIN code
a.
Turn the knob to select a number from 0 to 9.
Turn clockwise to increase the number and anticlockwise to decrease it.
b. Press the knob to confirm and set the next digit.
c. (Optional) To modify the previous digit, turn the knob anticlockwise until the number
becomes 0 and keep turning it one time more.
Important: Please do not set the PIN code to "0000".
d. Enter the PIN code again to complete setting the PIN code.
Note: Once your PIN code is set, you can update it at any time by navigating to Settings
> Change PIN Code in the app or selecting Settings > Change PIN on the display.
background
EN
19
Before network setup:
•
Make sure the robot and your mobile device are on the same Wi-Fi network.
•
Make sure that your mobile device is within 10 m (32.8 ft) of the robot.
•
Enable Bluetooth function on your mobile device.
4.2.2 Connect the Robot to the Internet
1
Scan the QR code to download the MOVAhome app on your mobile device.
You can also download MOVAhome app from App Store or Google Play.
2
Open the MOVAhome app, create an account, and log in.
3
Connect via one of the following methods:
•
Scan the QR Code: Go to
Device and tap Scan to connect. Scan the QR code located
inside the robot's top cover to connect.
•
Add Manually: Go to Device and tap Add. Then select your robot model to connect.
•
Automatic discovery: The robot will search for nearby devices. Tap your robot from the list
of discovered devices to connect.
4
Follow the in-app instructions to complete the Wi-Fi network connection.
Important:
•
Please use a single-band network of 2.4 GHz frequency.
•
Make sure your Wi-Fi network doesn't have a 󶀄rewall and isn't encrypted. Otherwise, the
network setup may fail.
OR
MOVAhome
background
EN
20
6
Follow the in-app instructions to complete the pairing.
Note: The Link Service allows remote control without Wi-Fi, but a Wi-Fi connection is
recommended for best performance.
5
Press and hold the knob on the control panel for 3 seconds. The robot will enter
Bluetooth pairing mode.
Unbind the Robot
Reset Your Robot
Once you reset the robot to factory settings, all data on the robot will be erased. You can
reset your robot via either of the following ways:
•
Press and hold Start and Back buttons together simultaneously for 3 seconds on the
control panel.
•
Go to Settings and select Reset the Robot via the display.
4.2.3 Other Settings
Log Out of and Delete Your Account
Share Your Robot
The robot is automatically bound to the MOVAhome account once pairing is successful.
Each device can only be bound to one account. It cannot be bound to another account at
the same time.
To pair the robot with a new account, you need to unbind it 󶀄rst. To unbind it:
1. Open the MOVAhome app. Go to
Device.
2. Locate your robot's name. If you have multiple robots bound to your MOVAhome
account, swipe left or right to access the page of the robot you want to edit.
3. Tap the robot's name in the upper left corner.
4. Select Delete.
Note: Once a robot is removed from the MOVAhome account, all user data acquired from the
robot will be erased from the server.
1. Go to
Me > Settings > General > Account.
2. Select Log Out or Delete Account.
1. Tap the robot's name in the upper left corner.
2. Select Device Sharing.
background
EN
21
Important: Before mapping, please check the following:
• The battery level of the robot is more than 50%.
• The protective cover of the LiDAR is removed.
5 Map Your Garden
•
The top cover is closed.
•
The robot correctly docks in the charging station.
Before starting the mapping process, please keep the following in mind:
•
Walk within 5 m (16.4 ft) behind the robot during the mapping process.
5.1 Create the Virtual Boundary
background
EN
22
•
The robot can navigate slopes with an incline up to 80% (38.7° ). However, for better
mowing results, it is recommended to keep the slopes of work areas below 45% (24° ).
•
For areas narrower than 1 m (39.4"), please set them as paths to allow the robot to pass
through. For details, see Set Path.
•
If your lawn is more than 6 cm (2.4") higher than the adjacent ground, keep the robot at
least 10 cm (3.9") away from the edge. If your lawn is level with the adjacent ground, the
robot can cross the perimeter for optimal mowing results along the edges.
•
Make sure the turning angles are greater than 90° . Angles smaller than 90° can make it
di󶀆cult for the robot to achieve a clean cut.
45%(24°)
1 m
1 m
6
Note: If the boundary is set on slopes steeper than 45% (24° ), the robot may slightly
slide beyond the boundary.
background
EN
23
Start Mapping:
1. Tap Start Mapping via the app, and the robot will check its status and calibrate.
2. Guide the robot remotely to the edge of your lawn and tap Set Starting Point to establish
the starting point for the boundary.
•
Remotely control the robot to move along the perimeter of your lawn to map out the work area.
•
Enable the Auto Boundary Detection mode to map out the work area. Powered by an
advanced AI algorithm, the robot can identify boundaries without the need for manual
guidance.
Caution: It will automatically leave the charging station to do the calibration. Please be careful.
Important:
•
The Auto Boundary Detection mode requires clear lawn boundaries and should be
used in daylight to ensure proper visibility. Avoid using this feature in poor light or rainy
conditions.
•
We recommend following the robot when you use the Auto Boundary Detection Mode. If
the robot fails to accurately detect the boundaries, you can exit Auto Boundary Detection
mode and switch to remote control at any time.
•
Make sure the robot's front camera is clean and unobstructed.
3. Map out the work area. The following two methods are supported.
OR
background
EN
24
4. When the robot returns to within 1 m (39.4") of the starting point, you can tap Close
Boundary to complete the boundary setting.
5. (Optional) Edit the map.
Alternatively, you can go to Device Page >
> Edit to adjust the map after the mapping is finished.
1
Set No-Go Zone
Though the robot can automatically avoid obstacles, it is still necessary to set areas with a risk
of falling, such as swimming pools and sandpits, as no-go zones. For objects you want to protect
(such as a flowerbed, a trampoline, a vegetable patch or an exposed tree root), please set them
as no-go zones.
2
Add or Expand Zones
• To Create More Zones
If your lawn is separated by roads or you have several isolated lawns, you can continue
creating work areas.
Note: If your garden has stone paths, designate them as separate zones. Then draw linking
paths so the robot can navigate between zones.
• To Expand Existing Zones
You can expand an existing zone by creating the area you want to include. If the two areas
overlap, they will be automatically merged.
background
EN
25
5. (Optional) Edit the map.
Alternatively, you can go to Device Page >
> Edit to adjust the map after the mapping is finished.
3
Set Path
For isolated zones, please create a path to connect them. Isolated zones without a path will
be inaccessible to the robot.
Note: By default, the robot only moves along the path without mowing the grass.
Important: If your lawn is divided by passages higher than 6 cm (2.4"), place an object with
a slope equal in height to the passage (such as a ramp).
• To Connect Two Isolated Work Zones
For isolated areas, please create paths to connect them. Otherwise, they will be inaccessible
to the robot.
Important: Make sure the beginning and end of the path are in the work area.
• To Connect the Work Area and the Charging Station
If your charging station is not in the work area, a path should be created to connect it to the work area.
Important:
• Ensure that one end is inside the work area, and the other end is right in front of the
charging station. It's advisable to align the path with the charging station.
• When creating paths to connect the work area and the charging station, do not remotely
dock the robot in the charging station. Otherwise, the LiDAR may be blocked, which can
cause the mapping to fail.
6cm
1.5m
background
EN
26
5.2 Add a Second Map
The Dual Map feature is designed for situations where the robot cannot autonomously travel
between separate lawns or when multiple maps are necessary.
You may need to create a second map if:
• Your front and back lawns can't be connected.
• There's a significant elevation difference between lawn areas.
• You have multiple properties but only one robot.
• Your lawn area is too large for a single map.
Note: If your lawns are connected and within the robot's capacity, use a Multi-Zone setup instead.
To map the second lawn:
4
Separate and Combine Zones
Divide a zone into smaller ones or merge zones that were divided into a larger one.
6. Tap Finish Map.
Important:
• Do not manually move the robot when creating the boundary, as this may cause the
mapping to fail.
• When the mapping begins, do not remotely dock the robot in the charging station until the
mapping process is complete. Otherwise, the LiDAR may be blocked, which can cause the
mapping to fail.
Map1
Map2
background
EN
27
Note:
• After switching the map, the schedules and mowing settings of the current map will be applied.
• You can purchase an additional charging station to install in the second map for greater
convenience. With a separate charging station installed in the second map, you only need to
move the robot manually between two maps.
1
. Prepare the charging station.
• If you have purchased a second charging station, install it on the second lawn.
• If not, move the robot and its charging station manually to start mapping the second lawn.
2. Navigate to Device Page >
and tap Add Map in the MOVAhome to create the second map.
3. Once you have finished the second map, you can switch between maps through
> Use.
6.1 Start Mowing for the First Time
6 Operation
Tips before mowing:
• Use a push mower to mow the grass to a height of no more than 12 cm (4.7").
• Clear the obstacles including debris, leaf piles, toys, wires and stones from the lawn. Make
sure no children or pets are on the lawn when the robot is mowing.
• Fill in the holes in the lawn.
• Set your mowing preferences in the app in advance (such as mowing efficiency, mowing height
and mowing direction).
You can select one of the following two methods to start mowing.
12cm
To map the second lawn:
background
EN
28
3. Turn the knob to select the mowing mode.
1. Open the robot's top cover.
2. Select Modes on the display and press the knob.
a) Start via the control panel
background
EN
29
4. Press the button, and close the robot's top cover to confirm. The robot will leave the
charging station and start all-area mowing.
1. Open the app.
2. Select a mowing mode and tap Start mowing to start mowing.
b) Start via the app
6.2 Mow the Lawn with Dual Maps
1. Manually move the robot to the map you want to mow.
2. Select the correct map in the app before beginning mowing tasks.
Note: After switching the map, the schedules and mowing settings of the current map will
be applied.
How to Handle Low Battery or Charging Issues?
For the tasks with only one charging station, if you don't manually relocate the charging
station along with the robot to the second map, the robot might deplete its battery and
prompt a charging failure since it can't locate the charging station. To resolve this issue,
please follow these steps:
a. Manually move the robot to the map with the charging station for recharging.
b. After charging, return the robot to the original map. It will resume mowing automatically.
Important: Do not change the map in the app during this process. This ensures the robot
remembers its last position and can continue where it left off.
C. Repeat these steps as needed until the entire lawn is mowed.
background
EN
30
OR
6.5 Return to the Charging Station
To send the robot back to its charging station:
1. Press the
on the control panel.
2. Confirm to pause or cancel the current task.
3.
Close the robot's top cover to confirm. The robot will automatically return to the charging
station to recharge.
Alternatively, you can send the robot back in the app.
6.4 Resume
To resume the task when the robot is paused, press the button, then close the robot's
top cover to confirm. The robot will resume the previous mowing task. Alternatively, you can
tap Continue in the app to resume the mowing task.
OR
6.3 Pause
To pause the current mowing task, you can press the Stop button on the robot or tap
Pause in the app.
Note: The robot cannot be started directly through the app after the Stop button is
pressed. To resume operation, enter your PIN code on the control panel.
OR
background
EN
31
Where You Can Explore More
MOVAhome app is more than a remote control. There are many things you can do through
the app: complete various settings remotely, experience different mowing modes, and adjust
mowing schedules.
7 MOVAhome App
7.1 Mowing Settings
Feature Location in APP Description
Mowing
Modes
Device Page >
Mode selection box
in the upper left
corner
The robot offers various mowing modes. You can switch
between modes through the app, including All-Area
Mowing, Zone Mowing, Edge Mowing, Spot Mowing and
Manual Mode.
Schedule
Device Page >
After the first map is completed, the robot automatically
creates two weekly mowing schedules according to the
lawn size, which are "Spr/Sum Schedule" and "Aut/Win
Schedule". With the schedule function, you can completely
leave the daily mowing work to the robot. You only need to
maintain the robot regularly.
Note: If you worry that the robot may disturb you or your
neighbours when it works autonomously during certain
hours, you can go to Settings > Do Not Disturb and set
Do Not Disturb time in the app.
Mowing
Shapes
Device Page >
> Edit > Shapes
Customise your lawn by adding shapes. Defined shapes
will be excluded from mowing in all mowing modes. You
can modify their position, size, or remove them in Shapes.
UltraTrim ™
Blade Disc
Device Page >
> UltraTrim ™
The UltraTrim ™ blade disc is designed to move to the
side when it reaches the lawn edges, ensuring a cleaner
cut. Refer to the MOVAhome app for specific operating
instructions.
7.2 Weather Protection Features
Feature Description
Rain Protection
When this function is enabled, the robot automatically pauses mowing and
returns to the charging station when it rains. You can set the rain protection
time in the app.
Note: Mowing wet grass can damage your lawn. It is advisable to extend the
protection duration to allow the grass to get dry before mowing again.
Frost Protection
Mowing in temperatures below 0° C (32° F) may cause permanent lawn
damage. For safety, the battery will not charge as a safety measure.
To protect your lawn and robot, you can enable the Frost Protection feature.
When enabled, the robot automatically pauses mowing and returns to the
charging station when the temperature falls below 0° C (32° F), and resumes
mowing once the temperature rises above 0° C (32° F) and the robot is able to
charge normally.
If you worry that adverse weather conditions may affect the mowing work, you can enable
the following weather protection features in Device Page > in the APP.
background
EN
32
7.3 Anti-theft & Safety Features
Feature Description
Lift Alarm
With this function enabled, an alarm will go off immediately when the robot is
lifted, and the robot will be locked. To resume operation, enter the PIN code
on the robot first.
Off-Map Alarm
With this function enabled, the robot will be locked and the alarm will go off
immediately if it is away from the map.
Real-Time
Location
With this function enabled, you can view the current location of the robot in
Google Maps.
Human Presence
Detection Alert
When enabled, the robot will notify you upon detecting human presence.
Child Lock
When enabled, the robot will be locked. Enable this feature when you worry
that children may operate the robot.
This section covers the robot’s anti-theft and safety features, including alarms for lifting
or moving off-map, real-time location tracking, human presence alerts, and a child lock to
prevent unintended operation.
To enable the anti-theft & safety features, go to Device Page >
in the APP.
Note: The off-map alarm and real-time location features are only available when the Link
Service is activated.
7.4 TrueGuard Features
7.5 Charging
Feature Description
Real-time Video
Tap
to view a live video feed from the robot’s front camera, allowing you
to monitor your garden anytime, anywhere.
Patrol
While the robot is on standby, you can send it to patrol specific boundaries or
spots in your garden via the app. To access this feature, go to
> Patrol.
This robot allows you to keep an eye on your garden with real-time video and patrols for
specific spots via the app.
You can adjust the charging settings through Device Page >
> Charging in the app.
7.5.1 Custom Charging Period
The Custom Charging Period feature allows you to customise the robot's charging period to
specific hours. When enabled, the robot charges itself to a safe battery level when the battery
level is low when there are no mowing tasks, and completes a full charge only during the
designated charging period.
background
EN
33
7.5.2 Battery Level Control
•
Battery Level for Auto-Recharge: Set the battery levels at which the robot automatically
returns to the charging station.
• Battery Level for Resuming Tasks: Set the battery levels at which the robot
automatically resumes unfinished mowing tasks.
Note: MOVA development team will continuously conduct OTA (Over-the-Air) updates and
maintenance on the firmware and app. Please check for update notifications or enable the
Auto-update function to keep the firmware and app up-to-date and enjoy more features.
8 Maintenance
For better performance and lifespan of the robot, please clean it regularly and replace worn
parts according to the frequency below:
Note:
• You can check the remaining time for blades and the cleaning brush by navigating
to Device Page >
> Consumables & Maintenance in the app. After replacing any
consumables as prompted, go to the details page for the consumable and tap I've
Replaced It to reset the timer.
• If you have designated areas in your garden for routine robot cleaning and servicing, you can
set Maintenance Points on the map by navigating to Device Page > > Head to Maintenance
Point > Edit Point. Once the maintenance points are set, you can simply tap Go and direct the
robot to the designated locations for easy servicing.
Part Replacement Frequency
Blades Every 6–8 weeks or sooner
Cleaning brush Every 12 months or sooner
Regularly clean your robot to prevent grass clippings and dirt from accumulating and clogging
the blade disc and drive wheels, which can affect its mowing, docking, and movement
performance. We recommend using a cleaning kit, available at local stores or online.
8.1 Cleaning
Warning: Before cleaning, please turn off the robot and unplug the charging station.
background
EN
34
2s
2. Cover the LiDAR with its protective cover.
3. Place the robot on its side and lean
it securely against a wall. Ensure that
the display, camera, and LiDAR are not
pressed against any surface.
4. Clean the housing, blade disc and
chassis with a hose.
Warning: Do not touch the blades when cleaning the chassis. Please wear gloves when cleaning.
Caution: Please do not use a high-pressure washer for cleaning. Do not use detergents for cleaning.
• The Housing, Chassis and Blade Disc:
1. Turn the robot off.
5. Use a lint-free cloth to carefully clean the LiDAR sensor.
background
EN
35
2s
• Charging Contacts and Front Camera:
Use a clean cloth to wipe the charging contacts on the robot and the charging station, and
also clean the front camera. Keep the charging contacts and the front camera dry after
cleaning.
• Drive Wheels:
Use a brush to remove mud from the wheels to ensure good grip.
8.2 Component Replacing
• Replace the Blades
To keep the blades sharp, please replace the blades regularly. It is recommended to replace the
blades every 6–8 weeks or sooner. Please only use the MOVA genuine blades.
Note: Please replace all twelve blades at the same time to ensure a balanced cutting system.
1. Turn off the robot. 2. Cover the LiDAR with its protective cover.
background
EN
36
5. Remove the twelve blades and
screws.
6. Align the new blades with the holes on
the blade disc, then secure them with the
screws.
• Replace the Cleaning Brush
When the cleaning brush for the LiDAR sensor wears out, its bristles may fray or deteriorate,
affecting its cleaning performance. Please replace the cleaning brush regularly to keep a good
cleaning result. It is recommended to replace the cleaning brush every 12 months or sooner.
3. Place the robot on its side and lean
it securely against a wall. Ensure that
the display, camera, and LiDAR are not
pressed against any surface.
4. Loosen the screws using a Phillips
screwdriver.
background
EN
37
9.1 Operating and Charging Temperature
The robot supports normal operation when the battery temperature is between -6° C (21° F)
and 57° C (135° F).
Do not charge the battery below 6° C (43° F) or above 57° C (135° F), as charging will be
blocked by the battery protection system. Charging resumes once the battery temperature
rises above 6° C (43° F) or drops below 57° C (135° F) and the battery is capable of
accepting charge.
Note: All temperature values allow a 3° C (37° F) deviation.
For best performance, it is recommended to operate the lawnmower in an ambient
temperature range of 10° C (50° F) to 30° C (86° F).
Low-Power Charging Mode:
When the low-power charging mode is activated, functions unrelated to charging will be
disabled (the network will be turned off).
To enable low-power charging mode, press and hold the
button and the button
simultaneously, and press the OK button 5 times quickly at the same time. You will hear a
voice prompt: Low-power charging mode is on.
To disable low-power charging mode, restart the robot.
9.2 Storage Requirements
For long-term storage, charge the robot every 6 months to protect the battery. Battery
damage caused by over-discharge is not covered by the limited warranty. The long-term
storage temperature for the battery should be between -10° C (14° F) and 35° C (95° F). To
minimize the damage, the recommended storage temperature for the battery is between
0℃ (32° F) and 25° C (77° F).
Note: The lifespan of the robot's battery depends on frequency of usage and hours of
operation. If the battery is damaged or cannot be charged, do not dispose of the obsolete
or faulty battery arbitrarily. Please obey local recycling regulations.
9. Battery
10 Winter Storage
11 Transport
•
The Robot
1. Charge the battery fully before turning the robot off.
2. Clean the robot thoroughly before putting it into storage in winter.
3. Put on the LiDAR protective cover.
4. Store the robot inside in a dry place, at a temperature above 0° C (32° F).
• Charging Station
Unplug the charging station and store it in a dry and cool place, away from direct sunlight.
Note: After winter storage, please reinstall the charging station and place the robot in
it to charge. If you reinstall the charging station in a different location, the robot will
automatically update the station's location as soon as it charges and leaves the station.
If you encounter positioning errors because of major changes in your garden, it's
recommended to remap the area.
For long distance transport, ensure that the robot is turned off. It is recommended to use
the original packaging. Please put on the LiDAR protective cover.
Warning:
• Please turn the robot off before transporting it.
• Lift the robot by the side handle, keeping the blade disc away from your body.
background
EN
38
12 Troubleshooting
Issue Cause Solution
The robot is not
connected to the app.
1. The robot is not within
Wi-Fi signal coverage or
Bluetooth range.
2. The robot is turned off or
is restarting.
1. Check if the robot has completed the process
of turning on.
2. Check if the router is working properly.
3. Move closer to the robot to establish a
Bluetooth connection.
Failed to connect to
Wi-Fi.
The robot only supports
2.4 GHz networks.
Ensure that you use a single-band network of
2.4 GHz frequency.
Robot lifted.
The wheel is not on the
ground.
1. Put the robot back on flat ground.
2. Enter the PIN code on the robot and confirm.
3. The robot can't cross objects higher than 6
cm (2.4"). Please keep the ground even where
it is working.
Robot tilted.
The robot tilts more than
80% (38.7° ).
1. Put the robot back on flat ground.
2. Enter the PIN code on the robot and confirm.
3. The robot cannot climb slopes greater than
80% (38.7° ).
Robot trapped.
The robot is trapped and
fails to get out.
1. Remove the surrounding obstacles and then
retry.
2. Manually move the robot to a flat and open
place inside the map and try starting the
task again. If you continue to encounter this
problem, please retry after the robot is in the
charging station.
3. Check if there are holes in the ground. Fill in
the holes before mowing to prevent the robot
from being trapped.
4. Check if the surrounding grass is taller than
12 cm (4.7"). You can adjust the obstacle
avoidance height or use a push mower to
mow the lawn in advance to prevent the robot
from being trapped.
5. If the robot is often trapped in this location,
you can set it as a no-go zone.
Drive wheels error.
The wheel cannot rotate
or the wheel motor has a
problem.
1. Clean the drive wheels and then retry.
2. If you continue to encounter this error, try
restarting the robot.
3. If the problem persists, please contact the
after-sales service.
Blade disc can't rotate.
The blade disc cannot
rotate normally or the
cutting motor has a
problem.
1. Clean the blade disc and then retry.
2. Check if the surrounding grass is taller than
12 cm (4.7"). You can use a push mower to
mow the lawn in advance to prevent the blade
disc from being blocked by tall grass.
3. Check if there is water under the blade disc.
If there is any, move the robot to a dry place
and then retry.
4. If you continue to encounter this error, try
restarting the robot.
5. If the problem persists, please contact the
after-sales service.
background
EN
39
Issue Cause Solution
The blade disc fails to
move up or down.
The blade disc fails to
move up or down.
1. Clean the blade disc and then retry.
2. If you continue to encounter this error, try
restarting the robot.
3. If the problem persists, please contact the
after-sales service.
The blade disc cannot
move to the side.
The blade disc cannot
move to the side.
1. Clean the cutting system and remove any
debris or foreign objects.
2. If you continue to encounter this error, you
can disable the UltraTrim ™ function first.
3. If the problem persists, please contact the
after-sales service.
4. Periodically apply lubricant to the blade disc's
offset pivot linkage.
Bumper error.
The front bumper sensor is
constantly triggered.
1. Check if the robot is trapped somewhere.
2. Gently tap the bumper and make sure it
bounces back.
3. If you continue to encounter this error, try
restarting the robot.
4. If the problem persists, please contact the
after-sales service.
Charging error.
The robot docks in the
charging station, but the
charging current or voltage
has a problem.
1. Check if the charging station is correctly
connected to power.
2. Check if the charging contacts on the robot
and the charging station are clean.
3. After checking is finished, try docking the
robot in the charging station again.
4. If the problem persists, please contact the
after-sales service.
Robot shuts down on
the spot.
Battery temperature is ≥
65℃ (149° F).
1. Use the robot when the battery temperature
drops below 57℃ (135 ℉ ).
2. If the problem persists, please contact after-
sales service.
Battery temperature is
< -15℃ (5° F).
1. Use the robot where the battery temperature
is above -9℃ (16° F).
2.If the problem persists, please contact the
after-sales service.
The robot pauses tasks
and auto-returns to
the station.
Battery temperature is ≥
62℃ (144° F).
1. Turn off the robot and wait for the battery
temperature to drop below 57° C (135° F). The
temperature will decrease automatically after
some time.
2. If the problem persists, please contact after-
sales service.
Battery temperature is
< -6℃ (21° F).
1. Use the robot where the battery temperature
is above -6℃ (21° F).
2. If the problem persists, please contact the
after-sales service.
background
EN
40
Issue Cause Solution
Robot is in the station
but does not charge.
Battery temperature is >
57℃ (135° F).
1. Turn off the robot and wait for the battery
temperature to drop below 57° C (135° F). The
temperature will decrease automatically after
some time.
2. If the problem persists, please contact after-
sales service.
Battery temperature is
< 6℃ (43° F).
1. Use the robot where the battery temperature
is above 6℃ (43° F).
2. If the problem persists, please contact the
after-sales service.
LiDAR is blocked.
LiDAR is blocked (for
example the LiDAR
protective cover is not
removed).
1. Remove the lidar protective cover and then
retry.
2. If lidar on the top of the robot is very dirty,
clean it with a lint-free cloth and then retry.
LiDAR malfunction.
LiDAR is very dirty or there
is a sensor error.
1. Check if the lidar is dirty. Clean it if necessary
and then try again.
2. If you continue to encounter this error, try
restarting the robot.
3. If the problem persists, please contact the
after-sales service.
LiDAR is dirty. LiDAR is dirty.
Wipe the LiDAR sensor on top of the robot
with a clean cloth. Keep the LiDAR dry after
cleaning.
LiDAR temperature is
high.
The LiDAR temperature is
high. LiDAR will stop soon.
1. The robot will automatically try to return to the
charging station to cool down.
2. Ensure the robot operates at an ambient
temperature below 40 ℃ (104° F).
3. Place the robot in a shaded, cool, and well-
ventilated area. The alarm will stop when the
temperature drops to a normal range.
4. The robot will automatically resume operation
once the alarm stops.
5. If the problem persists, please contact after-
sales service.
LiDAR temperature is
too high.
The LiDAR temperature
is too high. LiDAR has
stopped.
1. The LiDAR is turned off due to high
temperatures.
2. Ensure the robot operates at an ambient
temperature below 40 ℃ (104° F).
3. Place the robot in a shaded, cool, and well-
ventilated area. The alarm will stop when the
temperature drops to a normal range.
4. If the problem persists, please contact after-
sales service.
Robot is lost. Positioning is lost.
1. Check if the LiDAR on the top of the robot is
dirty. Dirt will affect the positioning.
2. Manually move the robot to an open place
inside the map and try starting the task again.
3. If the positioning is not recovered, remote
control the robot back to the charging station
via the app, and then start the mowing task.
background
EN
41
Issue Cause Solution
Sensor error. Sensor error.
1. Restart the robot and retry.
2. If the problem persists, please contact the
after-sales service.
The robot is in the no-
go zone.
The robot is in the no-go
zone.
1. Manually move the robot out of the no-go
zone and then retry.
2. Remotely control the robot through the app to
move it out of the no-go zone, and then retry.
The robot is outside
the map.
The robot is outside the
map.
1. Manually move the robot inside the map, and
then retry.
2. Remote control the robot back inside the map
via the app, and then retry.
Emergency stop is
activated.
The Stop button on the
robot is pressed.
Enter the PIN code on the robot and confirm.
Low battery. The robot
will shut down soon.
Battery level is ≤ 10%.
Dock the robot in the charging station to
charge.
The robot is away
from the map. Risk of
being stolen.
The robot is away from the
map.
1. Enter the PIN code on the robot and confirm.
2. You can disable the Off-Map Alarm in Settings
in the app.
Failed to return to the
charging station.
The robot cannot find the
charging station when
returning to the charging
station.
1. Check if there are obstacles blocking the
robot. Remove the obstacles and retry.
2. Remote control the robot back to the
charging station via the app.
Failed to dock in the
charging station.
The robot finds the
charging station but fails to
dock.
1. Check if the reflective films on the station are
dirty or blocked.
2. Check if there are obstacles in front of the
station.
3. Check if the station is moved.
4. Check if the baseplate is covered with thick
mud.
5. Check if the station is on a slope.
6. Check if the station has power.
7. Help the robot dock in the charging station by
using the remote control or manually.
Positioning failed.
Positioning fails when
the robot tries to start a
mowing task.
1. The lidar may be obstructed. Manually move
the robot to a flat and open place inside the
map and try starting the task again.
2. If you continue to encounter this error, please
retry after the robot is docked in the charging
station.
Insufficient space for
turning in front of the
station.
Insufficient space for
turning in front of the
station.
1. If the station is placed at the edge of the map
or within it, ensure there is at least 1 m (39.4")
of free space between the front area of the
station's baseplate and the boundary of the
map; otherwise, the robot may not be able to
make turns.
2. Relocate the station, or change the map in
Map Editing.
background
EN
42
Issue Cause Solution
Path obstructed. Path obstructed.
1. Check if a no-go zone is set in the path.
2. Check if there are obstacles blocking the
robot.
3. If the robot still cannot pass, delete the path
in Map Editing and set a new one.
The front camera is dirty. The front camera is dirty. Wipe the front camera with a clean cloth.
There is an issue with
the front camera.
There is an issue with the
front camera.
1. Wipe the front camera with a clean cloth.
2. Try restarting the robot.
3. If the problem persists, please contact the
after-sales service.
Front camera blocked. Front camera blocked. Wipe the front camera with a clean cloth.
Boundary detection
error occurs during
Auto-Mapping.
Boundary detection error
occurs during Auto-
Mapping.
1. Ensure that the lighting conditions are
suitable, neither too bright nor too dim.
2. Confirm that the weather is clear, avoiding
fog or rain.
3. Ensure that the front camera is clean and
unobstructed.
4. Ensure that the ground surface is even, as
bumps may affect detection.
5. If boundary detection continues to fail, switch
to remote control mode for mapping.
The robot vibrates
abnormally while
mowing.
Damaged or missing
blade(s) on the blade disc.
Immediately shut down the robot and inspect
the blade disc for missing, damaged, or loose
blade(s).
background
EN
43
13 Specifications
Basic
information
Product name
Robotic Lawn Mower
LiDAX Ultra 1000 AWD LiDAX Ultra 1600 AWD
LiDAX Ultra 2000 AWD
Brand MOVA
Model MXXM7100/MXXM7101/MXXM7102
Dimensions
740 mm × 532 mm × 321 mm
(29.1" × 20.9" × 12.6")
Weight (battery
included)
23.6 kg (52.0 lbs)
Mowing
Maximum mapping
area
1,000 m²
(0.25 acre)
1,600 m²
(0.4 acre)
2,000 m²
(0.5 acre)
Mowing height 3~10 cm (1.2~3.9")
Mowing width
40 cm
(15.7")
Charging time
[1]
65 min
Noise
emissions
Sound power level
LWA
66 dB(A)
Sound power
uncertainties KWA
3 dB(A)
Sound pressure level
LpA
58 dB(A)
Sound pressure
uncertainties KpA
3 dB(A)
Working
condition
Operating temperature
0~50° C (32~122° F)
Recommended: 10~35° C (50~95° F)
Long-term storage
temperature
-10~35° C (14~95° F)
Recommended: 0~25° C (32~77° F)
IP-classification
Robot: IPX6
Charging station: IPX4
Power supply: IP67
Maximum slope for
mowing area
80 % (38.7° )
Connectivity
Bluetooth frequency
range
2400.0–2483.5 MHz
Max. RF Power
802.11b:16±2dBm(@11Mbps)
802.11g:14±2dBm(@54Mbps)
802.11n:13±2dBm(@HT20,HT40)
Bluetooth: 7.49dBm
Wi-Fi
Wi-Fi 2.4 GHz
(2400–2483.5M)
Link service [2]
LTE-FDD: B1/3/5/7/8/20/28
LTE-TDD: B38/40/41
GSM: B2/3/5/8
(Free for 3 years from activation)
background
EN
44
Connectivity
Link service
coverage
Albania, Andorra, Australia, Austria, Belarus, Belgium, Bosnia and
Herzegovina, Bulgaria, Croatia, the Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Moldova, Monaco,
Montenegro, the Netherlands, New Zealand, North Macedonia, Norway,
Poland, Portugal, Romania, Russia, San Marino, Serbia, Slovakia,
Slovenia, Spain, Sweden, Switzerland, Ukraine, the United Kingdom,
and Vatican City.
GNSS [3] GPS/ GLONASS/BDS/Galileo
Driving motor Motor type Wheel Hub Motor
Cutting motor Speed 2500 /min
Battery (robot)
Battery model MBPM50
Battery type Lithium-ion battery
Typical capacity 7.5 Ah / 243 Wh
Rated voltage 32.4 V DC
Full charge voltage 37.8 V DC
Power supply
Charger model MPAM30
Input voltage 100~240 V AC
Output voltage 42 V DC
Output current 5 A
Charging
station
Charging station
model
MCM30
Input voltage 40 V DC
Output voltage 40 V DC
Input current 5 A
Output current 5 A
Accessories
Spare blades and
holders
36
Blade model MBKM10
[1] Charging time refers to the time needed to reach 85% capacity for resuming cutting
when the robot automatically returns to the charging station due to low battery.
[2] Requires the activation of the Link service.
[3] Requires the activation of the Link service.
Note: The specifications are subject to change as we continually improve our product. For
the latest information, please visit our website at https://www.mova.tech.

Specifications

Indexed Terms: Robot Lawn Mower, Wire-free

Mova LIDAX ULTRA 2000 AWD Questions and Answers

Questions and Answers

Related Products

Product Mova LIDAX ULTRA 2000 image
Mova LIDAX ULTRA 2000
2026-02-10 1 docs
Product Mova LIDAX ULTRA 1000 image
Mova LIDAX ULTRA 1000
2026-02-10 1 docs