A
20260903
SWXXXXXXXXXXXXD8
2026/09/03
陈萍
1.名称：D8中性英⽂英⽂说明书
2.材质：128g铜版纸⿊⽩印刷⻛琴折
3.尺⼨：60*80mm
4.印刷字印清晰，不断线、拖笔画不得有重线，杂点等缺陷。
5.尺⼨公差±0.2mm
V0.0
Self-powered Door Contact
INSTRUCTIONS
The door sensor is suitable for handleless flat-opening
doors such as cabinet doors, bookcase doors, and
wardrobe doors. Press the door panel to close the door,
and press it again to open the door. When paired with the
controller, it can automatically turn on the light when the
door is opened and automatically turn off the light when
the door is closed.
Product Description
Power supply: Self-powered
Communication frequency: RF433MHz
Modulation: FSK
Letter of agreement: 80m outdoor, 25m indoor
Communication distance: ≥100000times
Service life: -20~+55
Operating temperature: PC
Shell material: Fixed Inside the portal
Product Description
Pairing method with controller
After the controller enters the pairing mode (the indicator
light of the controller starts to flash slowly), quickly
press the door magnet once (press and release within
0.5 seconds). When the indicator light on the controller
stops flashing, the pairing is successful. After the pairing
is completed, the light can be turned on when the door is
opened and turned off when the door is closed.
Product features
Note: This pairing method simulates the directional pairing of a
wireless kinetic energy switch.
The door magnets can be paired into two control
modes
1. Door opening mode: After the controller enters the
pairing, press the door magnet (i.e.,close the door after
installation), and the pairing is formed as pressing (close
the door) to close and bouncing (open the door) to open.
This mode is mostly used for light control.
2. Door closing mode: After the controller enters the
pairing, the door magnet is bounced up (i.e., the door is
opened after installation), and the pairing is formed as
pressing (closing the door) to open and bouncing
(opening the door) to close. This mode is mostly used
for the control of air conditioners, electric heaters, etc.
The controller can be paired with multiple door magnets
for use. When multiple door magnets are paired, the
control mode of the first paired door magnet shall
prevail. For the door magnets in the door opening mode,
as long as one door magnet is in the bouncing state
(door-opening state), the controller will open. After all
door magnets are closed, the receiver will also close. For
the door magnets in the door closing mode, the receiver
turns on after all door magnets are turned off. As long as
one door magnet is in the bouncing state, it will turn off.
Usage method
1. Close the door panel
Push the door panel to close it. When the door magnetic
telescopic rod is pushed down to the bottom, it will be
fixed. The magnet at the top of the telescopic rod
adheres to the door panel through magnetic force,
ensuring that the door closes tightly.
2. Open the door panel
Press the surface of the door panel, and the door
magnetic telescopic rod will pop out, allowing the door
panel to be opened.
Cabinet Door application: Door magnets are suitable for
handle swing doors and are installed on cabinet doors.
When it is necessary to take out kitchenware, press the
cabinet door to open it, and the cabinet light strip will
automatically turn on. When the cabinet door is closed,
the cabinet light strip will automatically turn off.
Note: This function can be achieved by connecting the controller to
the cabinet light strip and pairing the D8 door magnet with the
controller.
Application scenarios Dimensions (mm)
CERTIFICATE
INSPECTED
FCC Warning
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and
receiver.
—Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV
technician for help.
Note: The Grantee is not responsible for any changes or
modifications not expressly approved by the party
responsible for compliance. such modifications could
void the user's authority to operate the equipment.
The device has been evaluated to meet general RF
exposure requirement.
To maintain compliance with FCC's RF exposure
guidelines, the distance must be at least 20cm between
the radiator and your body, and fully supported by the
operating and installation
1. Determine the installation position: Select the
installation position of the door magnet, which is usually
on the inner side of the door frame and the door panel, to
ensure that the two can be in close contact when the
door is closed.
2. Fix the door magnet: Use screws to secure the door
magnet into the door frame.
3. Test the door magnetic function: Close the door panel
and check if the door magnetic can close normally.
Gently touch the door panel to check if the door can be
opened smoothly.
Installation Instructions
