EG9837 Revised 04/24
5
5
1
7
7
6
2
12
1
8
4
9
(continued on next page)
CAUTION
INSPECT CONTENTS IMMEDIATELY AND FILE CLAIM WITH DELIVERING
CARRIER FOR ANY DAMAGE. SAVE YOUR BOX AND ALL PACKING MATERIALS.
YOU ARE RESPONSIBLE FOR DAMAGE TO YOUR UNIT IF RETURNED IMPROPERLY PACKED.
INSTRUCTION SHEET
#A202596
Security Units
ASSEMBLY INSTRUCTIONS
11
retaining clamps
(secures enclosure
panels to top and
bottom shelves)
Notches indicate
top and bottom
shelves.
** IMPORTANT TO NOTE IF YOUR UNIT
CAME WITH OPTIONAL CENTER SHELVES
Parts List
#1 . . . 2. . . Notched Wire Shelf **
#2 . . . 4. . . Posts
#3 . . . 2. . . (bags of four) Aluminum Split Sleeves
with Retaining Rings
#4 . . . 1. . . Spacer Box
#5 . . . 2. . . End Panels
#6 . . . 4. . .
3
⁄8˝- 16˝ x 1
1
⁄4˝ Tamper Proof Bolts
#7 . . . 1. . . Back Panel (48˝ & 60˝ units come in
two pieces)
#8 . . . 1. . . Left Door Panel
#9 . . . 1. . . Right Door Panel with Latch
#10 . . . 8. . . Bushings
#11 . . . * . . . Retaining clamps (#A221681)
#12 . . . * . . . Optional Center Shelves, if ordered.
#
qty description
* Varies per order.
door prong
end panel
(hinge tube)
bushing
9
5
10
Eagle Foodservice Equipment, Eagle MHC, and SpecFAB
®
are divisions of Eagle Group. ©2024 by the Eagle Group
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A.
• Phone: 302/653-3000 • 800/441-8440 • Fax: 302/653-2065
• www.eaglegrp.com • www.eaglemhc.com
1
**
**
bottom
shelf
split
sleeve
post
retaining ring
shelf collar
APPLY SPLIT SLEEVE RETAINING RINGS.
• Make sure the groove, located on top of
split sleeve, is accessible.
• Gently tap ring into the groove of each
split sleeve.
Security Units
ASSEMBLY INSTRUCTIONS
Step 2: Secure center shelves (if any) and top shelf.
DO NOT SECURE BOTTOM SHELF YET.
PLACE A BOARD ACROSS SHELF
CORNER AND GENTLY TAP WITH
HAMMER OR MALLET.
• Do NOT hammer directly on
wire or corner.
Step 1: Assemble shelves and posts, starting with bottom shelf.
NOTE: Bottom shelf must be assembled to posts FIRST.
ATTACH SPLIT SLEEVES TO POSTS.
• Wider part of taper goes toward the bottom.
• Make sure rib on split sleeve is seated into groove on post.
• Set aside retaining rings until later.
split
sleeve
corner
collar
post
MOUNT BOTTOM SHELF.
• Insert top of posts through
bottom of shelf corner collars.
• Slide shelf down posts until
split sleeves are seated inside
corner collars.
DO NOT SECURE YET!
IMPORTANT: IF YOU HAVE OPTIONAL CENTER SHELVES, THEY MUST BE INSTALLED
IMMEDIATELY AFTER INSTALLING BOTTOM SHELF. REPEAT STEP 1 TO MOUNT
OPTIONAL CENTER SHELVES (IF ANY), WORKING FROM BOTTOM TO TOP.
REPEAT STEP 1 TO MOUNT TOP SHELF.
#3 groove
on units with
casters
#7 groove
on stationary
units
#2 groove
on units with
casters
#6 groove
on stationary
units
top shelf
optional
center
shelf
optional
center
shelf
(continued on next page)
Units with
EAGLEgard finish
®
Units with chrome
or stainless finish
split
sleeves
Security Units
ASSEMBLY INSTRUCTIONS
Step 3: Attach end panels.
NOTE*: Additional standard shelves cannot be added once the end panels are in place.
TEMPORARILY RAISE BOTTOM SHELF.
• Place assembled shelf unit over spacer box
(same box the shelves were packed in).
• Lift bottom shelf off split sleeves, so shelf rests on
spacer box and posts touch the floor.
* Add-A-Shelf
®
and Quad-Adjust
®
shelves can be added after
assembly. Contact Eagle Group for more information.
ATTACH END PANELS TO UNIT.
• Place end panels in position.
Note: Large loops should be at the
bottom, small loops at the top.
• Tip unit slightly so bottom loops of
end panel can slide under bottom of
front and rear posts.
• Lift enclosure panel and position top
loops over top of front and rear posts.
• Secure end panel in place, using
“one-way” bolts.
Note: For stainless steel units, use
provided tamper-resistant #14
spanner insert bit to install bolts.
IMPORTANT: If using drill to assemble,
USE DRILL AT LOW
POWER SETTING.
REPEAT STEP 3 TO ATTACH
REMAINING END PANEL.
shelf unit
spacer box
split
sleeve
bottom
shelf
post
“one-way”
bolts
end panel
(bottom)
end panel
(top)
bottom
of front
post
• Use the retaining clamps
to secure back panel(s) to
top shelf (do NOT secure
bottom shelf yet).
• Place rear panel(s) in position. Insert rear panel prongs into end
panel hinge tubes as shown below.
Note: 36˝ units have one panel, 48˝ and 60˝ have two panels.
retaining
clamp
shelf
back panel(s)
(REAR VIEW)
Step 4: Attach rear panel(s).
rear
panel
prong
end
panel
hinge
tube
(continued on back page)
FOR SIDE-TO-SIDE
LENGTHS MORE THAN 36˝:
• Secure back panel(s) to
bottom shelf using
retaining clamps.
retaining
clamp
shelf
(REAR VIEW)
back panel(s)
Step 5: Secure bottom shelf.
Step 6: Attach casters or dolly truck to unit.
Step 7: Attach door panels.
Security Units
ASSEMBLY INSTRUCTIONS
• Place a board across each corner
and tap with hammer or mallet.
(End)
• Note: Insert bushings (provided) into hinge tubes of end panels BEFORE installing doors.
• Hang left door panel and right door panel.
TO CLOSE DOORS:
• Push left-hand door shut.
• Right-hand door features movable latch. Move
latch upward, push door shut, then move latch
downward. Latch hooks into top and bottom
shelves, keeping both doors closed.
• Remove spacer box and lower
bottom shelf onto split sleeves.
IF YOUR UNIT HAS CASTERS:
• Gently lay unit on its side.
• Insert caster stem into bottom of each post, and tap
with mallet. This may require several taps.
• Stand unit upright onto casters.
IF YOUR UNIT HAS A DOLLY TRUCK:
• Stand unit onto dolly truck.
• From underside of dolly truck,
run bolts (provided) through
dolly truck and fasten into
bottom of posts.
• Gently tap split sleeve
retaining ring into groove of
each split sleeve.
IF YOUR UNIT IS STATIONARY AND DOES NOT HAVE CASTERS OR DOLLY TRUCK, SKIP STEP 6 AND PROCEED TO STEP 7.
shelf collar
retaining
ring
bottom of post
dolly
bolt
door prong
end panel hinge tube
bushing
split
sleeve
bottom
shelf
post
Eagle Foodservice Equipment, Eagle MHC, and SpecFAB
®
are divisions of Eagle Group. ©2024 by the Eagle Group
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A.
• Phone: 302/653-3000 • 800/441-8440 • Fax: 302/653-2065
• www.eaglegrp.com • www.eaglemhc.com
