Regulatory Compliance
Flex Bridge 5
© 2026 TP-Link 1900002154 REV1.0.0
FCC Compliance Information Statement
Product Name: 5GHz 867Mbps Indoor/Outdoor Wireless Flex Bridge
Model Number: Flex Bridge 5
Component Name Model
I.T.E. Power Supply POE5430G-M2
Responsible party:
TP-Link Systems Inc.
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly app
roved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority
to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile
Configurations. The antennas used for this transmitter must be installed to provide a separation
distance of at least 43cm from all persons and must not be colocated or operating in conjunction
with any other antenna or transmitter.”
Product Name: I.T.E. Power Supply
Model Number: POE5430G-M2
Responsible party:
TP-Link Systems Inc.
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
We, TP-Link Systems Inc., has determined that the equipment shown as above has been shown
to comply with the applicable technical standards, FCC part 15. There is no unauthorized change
is made in the equipment and the equipment is properly maintained and operated.
Issue Date: 2026-03-04
CE Mark Warning
OPERATING FREQUENCY (the maximum transmitted power)
5150MHz—5250MHz (23dBm)
5250MHz—5350MHz (23dBm)
5470MHz—5725MHz (30dBm)
EU Declaration of Conformity
TP-Link hereby declares that the Access Point is in compliance with the essential requirements
and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and
(EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/
ce/.
RF Exposure Information
This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of
the general public to electromagnetic fields by way of health protection.
The device complies with RF specifications when the device used at 20cm from your body.
National Restrictions
Frequency band: 5150 - 5250 MHz:
Indoor use: Inside buildings only. Installations and use inside road vehicles and train carriages
are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached
to a fixed installation or to the external body of road vehicles, a fixed infrastructure or a fixed
outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 - 5250
MHz band.
Frequency band: 5250 - 5350 MHz:
Indoor use: Inside buildings only. Installations and use in road vehicles, trains and aircraft are
not permitted. Outdoor use is not permitted.
Frequency band: 5470 - 5725 MHz:
Installations and use in road vehicles, trains and aircraft and use for unmanned aircraft systems
(UAS) are not permitted.
UKCA Mark
UK Declaration of Conformity
TP-Link hereby declares that the Access Point is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK Declaration of Conformity may be found at
https://www.tp-link.com/support/ukca
National Restrictions
Attention: In Great Britain, the operation in the frequency range 5150MHz - 5350MHz is
only permitted indoors.
UK
Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to
the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux
CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Caution / Avertissement
Professional installation instruction
1. Installation personnel
This product is designed for specific application and needs to be installed by a qualified
trained person who has RF and related rule knowledge. This product needs to be professionally
configured by SDN Controller network service before use.
2. Professional Installation Requirements
• This device is generally for industrial/commercial use, which only sold to authorized dealers
or installers.
• Operation in the 5150-5250MHz is restricted to indoor use only.
• (For models with DFS function:) Operation in the 5600-5650MHz band is prohibited.
Instructions d'installation pour les professionnels
1. Personnel d'installation
Ce produit est conçu pour une application spécifique et doit être installé par une personne
qualifiée et formée, possédant des connaissances en RF et en règles associées. Ce produit doit
être configuré par des professionnels via le service réseau SDN Controller avant utilisation.
2. Exigences d'installation à l’attention des professionnels
• Cet appareil est généralement destiné à un usage industriel/commercial, vendu uniquement
à des revendeurs ou installateurs agréés.
• Le fonctionnement dans la bande 5150-5250 MHz est limité à une utilisation en intérieur
uniquement.
• (Pour les modèles avec fonction DFS:) Le fonctionnement dans la bande 5600-5650 MHz est
interdit.
1) The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems; 5150 MHz to 5350
MHz is restricted to indoor operations in Hong Kong.
2) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in
the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies
with the e.i.r.p. limit;
3) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in
the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits
specified for point-to-point and non-point-to-point operation as appropriate; and
DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350 MHz, 5470-
5600MHz, and 5650-5725MHz.
1) Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux;
2) Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant
les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la limitation P.I.R.E.;
3) Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la
bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour l’exploitation point
à point et non point à point, selon le cas.
Les produits utilisant la technique d'atténuation DFS (sélection dynamique des fréquences) sur
les bandes 5250- 5350 MHz, 5470-5600MHz et 5650-5725MHz.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de
20cm de distance entre la source de rayonnement et votre corps.
Industry Canada Statement
CAN ICES (B)/NMB (B)
Korea Warning Statements
당해 무선설비는 운용중 전파혼신 가능성이 있음 .
NCC Notice & BSMI Notice
注意！
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變
更原設計之特性及功能。
低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改
善至無干擾時方得繼續使用。
前述合法通信，指依電信管理法規定作業之無線電通信。
低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
應避免影響附近雷達系統之操作。
安全諮詢及注意事項
■
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
■
清潔本產品之前請先拔掉電源線 . 請勿使用液體、噴霧清潔劑或濕布進行清潔。
■
注意防潮，請勿將水或其他液體潑灑到本產品上。
■
插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
■
請勿將本產品置放於靠近熱源的地方 . 除非有正常的通風，否則不可放在密閉位置中。
■
不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商聯繫。
■
( 適用於配電源供應器出貨的產品 ) 電源供應器应使用在环境温度低於或等於 40℃的室內。
限用物質含有情況標示聲明書
產品元件名稱
限用物質及其化學符號
鉛
Pb
鎘
Cd
汞
Hg
六價鉻
CrVI
多溴聯苯
PBB
多溴二苯醚
PBDE
PCB
○ ○ ○ ○ ○ ○
外殼 ○ ○ ○ ○ ○ ○
天線 ○ ○ ○ ○ ○ ○
其他及其配件 — ○ ○ ○ ○ ○
備考1."超出0.1wt%"及"超出0.01wt%"系指限用物質之百分比含量超出百分比含量基準值.
備考2."○"系指該項限用物質之百分比含量未超出百分比含量基準值.
備考3."—"系指該項限用物質為排除項目.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
■ Keep the device away from fire or hot environments. DO NOT immerse in water or any other
liquid.
■ Do not attempt to disassemble, repair, or modify the device. If you need service, please
contact us.
■ Do not use damaged charger or USB cable to charge the device.
■ Do not use any other chargers than those recommended.
■ Do not use the device where wireless devices are not allowed.
■ (For models with adapters and power supply cord) Plug the product into the wall outlets with
earthing connection through the power supply cord.
■ (For models with adapters) The socket-outlet shall be installed near the equipment and shall
be easily accessible.
■ (For models with adapters) Make sure the power socket has a good contact with the ground.
■ (For models with adapters) Adapter shall be installed near the equipment and shall be easily
accessible.
■ (For models with adapters) Adapter should be used indoors where the ambient temperature
is lower than or equal to 40
℃
.
■ (For models with adapters) Use only power supplies which are provided by manufacturer
and in the original packing of this product. If you have any questions, please don’t hesitate to
contact us.
■ Operating Temperature (
運作溫度
):
-40℃–70℃(-40℉ –158 ℉ )
■ This product uses radios and other components that emit electromagnetic fields.
Electromagnetic fields and magnets may interfere with pacemakers and other implanted
medical devices. Always keep the product and its power adapter more than 15 cm (6 inches)
away from any pacemakers or other implanted medical devices. If you suspect your product
is interfering with your pacemaker or any other implanted medical device, turn off your
product and consult your physician for information specific to your medical device.
Please read and follow the above safety information when operating the device. We cannot
guarantee that no accidents or damage will occur due to improper use of the device. Please use
this product with care and operate at your own risk.
Explanation of the symbols on the product label
產品標籤上符號的解釋
Note: The product label can be found at the bottom of the product and its I.T.E. power supply.
Symbols may vary from products.
注意：產品標籤可以在產品底部和其 I.T.E. 電源供應器上找到。產品標籤可在產品底部找到。符號可能
因產品而異。
Symbol
符號
Explanation
說明
Class II equipment
二級設備
Class II equipment with functional earthing
具有接地功能的二級設備
Alternating current
交流電
Direct current
DC 電壓
Polarity of d.c. power connector
輸出端點的極性
For indoor use only
僅供室內使用
Dangerous voltage
危險電壓
Caution, risk of electric shock
請注意，有觸電的危險
Energy efficiency Marking
能源效率標誌
Protective earth
保護接地
Earth
接地
Frame or chassis
框架或外殼
Functional earthing
功能接地
Caution, hot surface
請注意，表面過熱
Caution
警告
Operator's manual
操作手冊
Stand-by
待機
"ON"/"OFF" (push-push)
“開啟”/”關閉”（按壓式）
Fuse
保險絲
Fuse is used in neutral N
保險絲用於中性線 N
RECYCLING
回收
This product bears the selective sorting symbol for Waste electrical
and electronic equipment (WEEE). This means that this product must
be handled pursuant to European directive 2012/19/EU in order to be
recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling
organization or to the retailer when he buys a new electrical or electronic
equipment.
這個產品帶有歐盟指令 2012/19/EU 中關於廢棄電氣電子設備（WEEE）的
選擇性分類標誌。這意味著，該產品必須按照該指令處理，以便進行回收
或拆解，從而最大限度地減少對環境的影響。
用戶可以選擇將產品交給有資格的回收機構，或在購買新的電器或電子設
備時將其交給零售商進行回收。
Caution, avoid listening at high volume levels for long periods
請小心，避免長時間以高音量收聽。
Disconnection, all power plugs
斷線，所有電源插頭
m
Switch of mini-gap construction
迷你間隙結構開關
µ
Switch of micro-gap construction (for US version)
Switch of micro-gap / micro-disconnection construction (for other
versions except US)
小間隙結構開關（US 版本）
小間隙 / 小斷開結構的開關（非 US 版）
ε
Switch without contact gap (Semiconductor switching device)
無接觸間隙的開關（半導體開關設備）
ErP Information:
1) Power consumption in networked standby: 5.4W.
2) Power consumption in networked standby when all wired network ports are connected and
all wireless network ports are activated: 6.5W.
3) The default period of time after which the power management function switches the
equipment automatically into a condition providing networked standby: 20 minutes.
4) How to activate and deactivate wireless network: Enter the webpage of product through
wired connecting. The wireless function can be turn on/off via ‘Wireless -> Management
Radio -> Enable 2.4GHz Wireless Checkbox’.
5) Use only power supplies listed in the user instructions.
Manufacturer Model
TP-Link T120100-2C4
TP-Link POE5430G-M2
Mounting Requirements 安裝需求
For safety, we recommend you to use the original screws in the package when mounting. The
following are alternatives to mount the device on the wall:
為了安全起見，我們建議您在安裝時使用包裝中原本提供的螺絲。以下是固定設備到牆壁上的替代方
法：
• Use 4 screws which comply with ANSI B1.1 4#, 6# standard and are longer than 25 mm.
請使用符合 ANSI B1.1
4#, 6#
標準且長度超過 25毫米的 4 顆螺絲。
