Portable Wireless Speaker
Quick Start Guide
Sound Air1
Check to make sure you have
everything below.
What's in the Box
D
Portable Wireless Speaker
Quick Start Guide
Sound Air1
A: 1* Sound Air1 Portable Speaker
B: 1* Type-C USB Charging Cable
C: 1* 3.5mm AUX Audio Cable
D: 1* Quick Start Quide
Device Overview
1. Power On/Off
3. Play/Pause
2. Previous Button
6. Next Button
4. TWS/Mode
5. Indicator light
12. Indicator light
10.USB port
11.Type-C charging port
13.TF card jack
7.Volume +
8.Volume -
9.AUX jack
Buttons and Ports
Volume +
Press to increase the volume.
Volume -
Press to decrease the volume
TWS/Mode
Long Press to conntect with two speakers.
Long Press to disconnect both speakers.
Next Button
Short Press to go to next song.
Play/Pause/Answer Button
Short press to pause/play the music.
Short press to accept an incoming call. (BT mode)
Double click to call back. (BT mode)
Long press to reject an incoming call. (BT mode)
Long press to disconnect/reback BT.
Power On/Off
Long press and hold to turn the speaker on/off.
Previous Button
Short Press to go to previous song.
Charging Your Device
Plug the included USB type-C cable into the speaker's charging port,
and connect another end of the cable to a power adapter
(not included).Allow approximately 4.5 hours to full charge the
battery.
When the battery is low and the blue light slow flash, please charge it.
The indicate light is red color when it's charging.
The red light will be off when it's full charged.
Note: We recommend using a USB wall adapter with a DC 5V output.
Charging port (USB Type-C)
Blue Indicator light
Red Indicator light
Initial Setup
1. Once your speaker is fully charged, press and hold the
Power button until you hear a voice prompt indicating the
device has entered BT paring mode.
2. On your smartphone or tablet, search for the BT device named
"Bobtot Sound Air1" and tap to connect.
3. A prompt will play once pairing is successful.
Note:
1. When you turn on the speaker but no connection, it will
automatically shut down after 10 minutes.
2. When you connected the speaker but no playback, it will
automatically shut down after 20 minutes.
Bobtot Sound Air1
BT device
TWS Sync Mode
1.Long press the " " about 2s on both speakers to turn them on,
and the blue light flashes.
2.
Long press
the " " on any one speaker, a prompt sound
"connected"indicates the speakers enter into pairing mode, the
indicator light of one speaker turned solid blue.
3.On your smartphone or tablet, search for the BT device named
"Bobtot Sound Air1
" and connect it, you could hear the sound
"connected" again, which means connect successfully.You can enjoy
the music with two speakers together.
Notes:
*In TWS Mode, turn off one of the speakers, both of them are off.
*Long press " " to exit TWS mode
Light Status
Mode Indicator light
Power supply Indicator light
Blue light flash: in BT pairing or TWS pairing status
Blue light slow flash: Low battery
Stay red light: Charing
Red light off: Full charge
Hands-Free Calling
Resetting Your Device
If your speaker is not operating properly, you may
reset it. To do so, press and hold the power
button for approximately 8s until the speaker
powers off, and then power it on again as usual.
Play/Pause/Answer Button
Short press to pause/play the music.
Short press to accept an incoming call. (BT mode)
Double click to call back. (BT mode)
Long press to reject an incoming call. (BT mode)
Long press to disconnect/reback .(BT mode)
VolumeDown
Press to decrease the volume.
Volume Up
Press to increase the volume.
Specifications
-Model Name: Sound Air1
-Outdoor Portable Wireless Speaker
-Input Power: DC 5V
-Impedance:3Ω
-Signal to Noise Ratio:≥78dB
-IPX6 water-resistant,sprayproof
-Built-in rechargeable battery
-Built-in Mic
-Range 33ft(10m)
-Frequency Response: 180Hz- 18KHz
-TWS Sync Mode(Pair 2 of these speakers together)
-Up to 25 hours of playtime (battery life is measured
as number of playtime with volume set at50%)
Any changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
FCC Warming
against harmful interference in a residential
installation.
This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment
and receiver.
FCC Warming
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
The device has been evaluated to meet general RF
exposure requirement. The device can be used in
portable exposure condition without restriction.
FCC Warming
Need help?
Customer Care Guide
At our company, we strive to provide exceptional customer
care to every one of our clients. We believe that building
strong relationships with our customers is essential to the
success of our business. To help us achieve this goal, we
have put together the following customer care guide.
Time
We understand that our customers' time is valuable, so we
will respond to any inquiries within 24 hours.
Feedback
We know that our customers are the heart of our business
so we value your feedback. We encourage you to share your
thoughts and ideas with us.
Solutions
If our customers encounter any issues, we will try our best to
find a quick and efficient solution that meets your needs.
Here at Bobtot, we take customer care very seriously. Our
customers are our first priority, and we are committed to
providing the highest quality service.
If you have any questions or concerns, please don't
hesitate to reach out to us.
We will be happy to assist you:
Call or Message: +1 888 572 1718
Email: [email protected]
Need help?
©2024 BOBTOT // Features and specifications are subject to change and or improvement without notice.
bobtot.net
