CDCW-SSXS CDCW-SSXA
User Guide
VAX SpinScrub Power
Carpet Washer
2
Safety information
Basic Safety Precautions
• Only use the machine indoors and keep the area you’re cleaning well lit.
• Keep fingers, hair and loose clothing away from moving parts and openings
whilst using the machine.
• Before using the machine test your carpets/rugs/upholstery for colourfastness
and pile distortion.
• This machine is not intended to be used or cleaned by persons with reduced
physical, sensory or mental capabilities, or lack of experience or knowledge,
unless they have been given instructions concerning the safe use of the
appliance by a person legally responsible for their safety. They should be
supervised whilst using the appliance. Children shall not use, clean or play with
this appliance, which when not in use should be secured out of their reach.
• Only Vax recommended tools and solution should be used with this machine.
Using other solutions may invalidate the guarantee.
Don’ts
• Don’t leave the machine plugged in when unattended.
• Don’t use the machine if it has been dropped, damaged or left outdoors.
• Don’t run over the power cord or use the machine if the power cord or plug
is damaged. If the power cord is damaged, it must be replaced by a qualified
person in order to avoid a hazard.
• Don’t use the machine to pick up any flammable or combustible materials
(lighter fluid, petrol, kerosene etc.) or use the machine in an area with explosive
vapours or liquid.
• Don’t handle the plug or use the machine with wet hands.
• Don’t pull or carry the machine by the power cord.
• Don’t use the machine to pick up hot coals, cigarette butts, matches or smoking
hot burning items or use in an area where there may be harmful fluids
(chlorine, bleach and ammonia drain cleaner).
• Don’t use the power cord as a handle, pull the power cord around corners or
sharp edges, or close a door over the power cord.
• Don’t unplug the machine by pulling on the power cord.
• Don’t carry the machine while it’s switched on.
• Don’t attempt to remove blockages with sharp objects as this may cause
damage to the machine. Remove blockages only as instructed in the user guide.
• Don’t use the machine with incorrect voltage as this may result in damage or
injury to the user. The correct voltage is listed on the ratings label.
This machine is intended for household use only, not for commercial or industrial use.
Please keep instructions for future use and use only as instructed in this guide.
3
• Don’t over saturate your flooring. Always finish on a dry stroke.
• Don’t use on a surface that is damaged, uneven or incorrectly fitted.
Do’s
• Check with the manufacturer of your flooring prior to using the machine.
• Always vacuum your flooring and upholstery thoroughly before using the
machine.
• Test all carpets/rugs/upholstery before full usage. Run the machine over a
small hidden area. If no damage or pile distortion occurs continue cleaning.
• The clean water tank should be filled with warm water (max 40°C) only.
Filling the clean water tank with hot or boiling water will damage the machine
and invalidate the guarantee.
• Always replace the fuse in the plug with a British standard 13amp fuse.
• Always unplug the machine before carrying out any maintenance and before
connecting or disconnecting the hose/accessories.
• Always check the machine, tools and accessories are free from damage,
dirt/debris before using.
• Take extra care when cleaning on the stairs.
• Always protect the power cord from heated surfaces and open flames.
• Turn off all controls on the machine before disconnecting or connecting
the power cord. After use always wrap the power cord around the cord
clips provided.
• Always keep the power cord away from the brushes whilst using the machine.
• Use only CE/UKCA approved 13amp extension cords, non-approved extension
cords may overheat. Care should be taken to arrange the extension cord as it
can be a trip hazard.
• Always use the machine with all water/solution tanks and filters in place.
• Keep all openings clear and free from debris as this may affect the airflow/
suction/water pick up.
• Always use the machine in an upright position. To prevent motor damage from
dirty water, never hold the machine upside down or on its side.
• Store the machine in a cool, dry area. Before storing the machine please
ensure all water tanks are empty and filters are thoroughly clean and dry.
4
Welcome to the Vax family!
You're now the proud owner of a VAX SpinScrub Power.
Here you’ll find everything you need to know about your machine and, most importantly,
instructions on how to get started so that you can get cleaning!
Introduction
Safety information
Introduction
Machine overview
Quick start
Getting started
Using your machine
Cleaning and maintenance
Troubleshooting
Guarantee and technical
Contents
2 - 3
4
5
6
7
8 - 12
13 - 15
16
17
Bought your product directly from vax.co.uk?
Relax - your guarantee will be automatically emailed to you.
Contact us if you haven’t received this and we’ll be happy to help.
Bought elsewhere? Registering is
quick and easy.
Scan this QR code or visit vax.co.uk/registration
Register your product to activate your free 6 year guarantee
Please see the back cover of this User Guide for more detail.
5
Machine overview
Weight 8.9kg. Cord length 7.6m.
Dirty water tank capacity 3L.
Solution tank capacity 0.5L.
Clean water tank capacity 4.5L.
*Included with model CDCW-SSXA only.
Subject to technical change without notice.
Images are illustrative only.
19 2018 21
1
Handle
2
Water/Solution trigger (hidden)
3
Clean water tank release handle
4
Clean water tank cap
5
Clean water tank
6
Dirty water tank release handle
7
Dirty water tank
8
Hose connection port cover
9
Nozzle
10
Spinscrub brushes
11
Quick release cord hook
12
Solution tank
13
Cord hook
14
Quick/Deep clean mode dial
15
Carry handle
16
ON/OFF pedal
17
Recline handle release pedal
18
2.5m Hose
19
Upholstery Wash Tool
20
SpinScrub Tool*
21
Accessory Bag
22
250ml Solution
22
*
16
11
17
12
13
14
15
1
2
5
3
6
9
7
10
4
8
SCAN HERE TO GET TO
KNOW YOUR MACHINE
visit www.vax.co.uk
for help and support with
setting up your machine
6
Quick start
Assembly
Push the handle
onto the extension
pole until it clicks
into place.
Slide the handle
into the main body.
It will click when
correctly fitted.
Filling clean water tank
Fill the clean water tank with
warm water (max 40�C).
Wash
Squeeze the trigger to
release water/solution
on the forward stroke.
Release the trigger
on the backward
stroke to pick up
water/solution.
Filling solution tank
Fill the solution tank with the
VAX carpet cleaning solution.
SCAN HERE TO WATCH OUR HOW-TO VIDEOS
or visit support.vax.co.uk for help and support
with using your machine
21
3 4
40°C
MAX
7
Getting started
PLEASE READ THE SAFETY GUIDE BEFORE USE.
IMPORTANT: Carpets should be dry vacuumed thoroughly before washing.
• Empty and rinse out clean and dirty water tanks and leave to air dry before storage.
• This is a powerful machine, before plugging in make sure all controls are turned off and hold the
machine firmly when starting and during use.
• Test for colourfastness - Wet a white absorbent cloth with the solution. In a small hidden area of
your carpet/rugs/upholstery, gently rub with the dampened cloth. Wait ten minutes and check
for colour removal or bleed with a white paper towel or cloth. Check all carpets/rugs/upholstery
material before first use and if your carpet has more than one colour, check all colours.
• Test all flooring/carpets/rugs before first usage. Run the machine over a small hidden area. If no
damage or pile distortion occurs continue cleaning.
• When using the machine, basic safety precautions should always be observed. Do not over
saturate your carpets and continue using dry strokes until little water is visibly passing through the
nozzle. When using the hose and tools always finish on a dry stroke.
• When cleaning an entire room, move furniture out of the area to be cleaned. If the furniture cannot
be moved, place aluminium foil or wax paper under the legs. This will prevent wood finishes from
staining your carpet. Pin up furniture skirts and curtains.
• Only use VAX carpet solution. Using other solutions may cause excess foaming and will invalidate
the guarantee.
• For heavily soiled areas, it may be necessary to repeat the cleaning process. Make criss-crossing
strokes across the original pattern and overlap with each pass.
• The clean water tank should only be filled with warm water (max 40�C). Filling the clean water
tank with hot/boiling water will damage your machine and invalidate the guarantee.
• Empty and rinse out clean and dirty water tanks and leave to air dry before storage. Do not leave
solution stored in the tanks between uses.
• This is a powerful machine, before plugging in make sure all controls are turned off and hold the
machine firmly when starting and during use.
Stand the base of the
machine on the floor in the
upright position.
Push the handle onto the
extension pole until it clicks
into place. Slide the handle
into the main body, it will
click when correctly fitted.
Align the clean water
tank with the body of the
machine. Slide it down and
press firmly into place.
Slide and push the
solution tank firmly into
the machine.
Assembly
8
Using your machine
IMPORTANT: Screw the solution tank cap tightly when refitting. Do not leave the solution stored in
the tanks between uses. Unused solution can be poured back into the bottle.
Filling the solution tank
Pull up the solution tank
and lift to remove.
To replace, slide and push
the solution tank firmly into
the machine.
Twist the solution tank cap
anti-clockwise and remove.
Fill the solution tank with
the VAX carpet cleaning
solution.
Pull and lift to remove the
clean water tank.
Twist the clean water
tank cap anti-clockwise
and remove.
Fill the clean water tank
with warm water
(max 40�C). Replace the
cap and twist clockwise
to tighten.
Filling the clean water tank
Twist the solution tank cap
clockwise until tight.
To replace the clean water
tank, align the back of the
clean water tank with the
body of the machine.
Slide it down and press
firmly into place.
40°C
MAX
9
Using your machine
IMPORTANT: Carpets should be dry vacuumed thoroughly before washing. For heavily soiled
areas, it may be necessary to repeat the cleaning process. Make criss-crossing strokes across the
original pattern and overlap with each pass. Do not over saturate the carpet. Always finish with
dry strokes (trigger released) and continue using dry strokes (trigger released) until little water is
visibly passing through the tool/nozzle.
Operation
Clip the cord into the cord
hook so that the cord does
not get pulled, caught or
tangled under the machine.
Plug into the mains and
press the ON/OFF pedal to
switch on.
Choose the cleaning mode by turning the dial.
1. Quick Clean Mode:
Best for a quick, surface clean - carpets dry in less
than an hour.
2. Deep Clean Mode:
Best overall results for a thorough, deep clean.
Press the handle release
pedal and pull the handle
backwards to recline
the machine.
Squeeze the trigger to
release the solution and
water mix.
For best results apply water/solution on the forward
stroke and release the trigger on the backward stroke to
pick up water/solution. For a dryer finish, follow with an
additional dry stoke without the trigger pressed.
CAUTION: The brushbars constantly spin when switched on and the machine is reclined. Never use
on one spot for an extended period of time as the brushbars may damage the floor surface.
1 2
SCAN HERE TO GET TO
KNOW YOUR MACHINE
visit www.vax.co.uk
for help and support with
setting up your machine
10
Using your machine
IMPORTANT: Optional step: To extract any remaining solution from your carpet, rinse your carpets
with water only. Do not over saturate your carpet.
Rinsing the carpet
To rinse, pull up the solution
tank and lift to remove.
To replace the clean water
tank, align the back of the
clean water tank with the
body of the machine. Slide
it down and press firmly
into place.
Pull and lift to remove the
clean water tank.
Twist the clean water
tank cap anti-clockwise
and remove.
Fill the clean water tank
with warm water (max
40�C). Replace the cap and
twist clockwise to tighten.
For best results apply water on the
forward stroke and release the trigger
to pick up water on the backward
stroke. Follow with a slow additional
dry stroke without the trigger pressed
for a dryer finish.
40°C
MAX
SCAN HERE TO GET TO
KNOW YOUR MACHINE
visit www.vax.co.uk
for help and support with
setting up your machine
11
Using your machine
Using the hose and tools
IMPORTANT: The machine should be in the upright position when using the hose and tools; this will
de-activate the brushes. Do not over saturate the carpet/surface. Always finish with dry strokes
(trigger released) and continue using dry strokes (trigger released) until little water is visibly passing
through the tool/nozzle.
SpinScrub Hand Tool*
For targeting stains and
stubborn marks.
*SpinScrub hand tool included with model CDCW-SSXA only.
Lift the hose connection
port cover.
Firmly push the hose end
into the hose connection
port.
Upholstery Wash Tool
For use on upholstery and
carpeted stairs.
Plug the machine into the
mains and press the
ON/OFF pedal to switch on.
Press the trigger on the forward stroke to
release water/solution. Release the trigger on
the backward stroke to pick up water/solution.
For a dryer finish continue using dry strokes
(trigger released) until little water is visibly
passing through the tool.
Select a tool. Slide the
tool over the tab at the
end of the hose until it
clicks into place.
12
Using your machine
Removing the hose and tools
To remove the Upholstery
tool, lift the clear plastic clip
up over the button on the
end of the hose.
To remove the hose press the
button on the underneath of
the hose and pull to remove.
Always close the hose
connection port cover
after using the hose. The
machine may lose suction
if it is not closed properly.
SCAN HERE TO GET TO
KNOW YOUR MACHINE
visit www.vax.co.uk
for help and support with
setting up your machine
To remove the SpinScrub
tool, press the button on
the top of the tool and pull
to remove.
13
Cleaning and maintenance
IMPORTANT: The motor is equipped with a thermal cut-out. If for any reason the machine should
overheat, the thermostat will automatically turn the machine off. Switch off and unplug the machine.
Check the machine for blockages and clean the dirty water tank filter.
Emptying and cleaning the dirty water tank
Hold the dirty water tank
handle and pull to remove.
To remove the lid, pull to
release the latch and push
down to unhook the clip
from the tank.
Lift the lid to remove. Empty the dirty water
tank over the sink or toilet.
Rinse under warm water
(max 40°C) to remove
dirt/debris.
To replace the lid, fit the
tab on the front of the lid
into the front of the dirty
water tank.
Close the lid. Hook the
bottom of the latch on the
tank and push the top of
the latch up and inwards
until it clicks into place.
To replace the dirty water
tank, push the tank into
the machine until it clicks
into place.
CAUTION: Always switch off and unplug the machine before performing any maintenance/
troubleshooting checks.
The dirty water tank is fitted with a float. When the dirty water tank is full or the floorhead is not in
contact with the carpet, the float will activate by shutting off the suction on the machine. This will be
noticeable as the motor noise on the machine will increase. If the float has been activated empty the
dirty water tank if it is full. If the dirty water tank is not full turn off the machine at the power switch
and wait for the float to settle before restarting your machine.
Empty and rinse out the clean and dirty water tanks and leave to air dry before replacing.
Do not leave solution stored in the tanks between uses.
14
Cleaning and maintenance
IMPORTANT: Carpets should be dry vacuumed thoroughly before washing. This will prevent excessive
build up of dirt/debris in the nozzle. If the nozzle is fitted incorrectly, this will cause poor dirty water
pick up.
Removing and cleaning the nozzle
Remove both tanks and tilt
the machine back.
Pull to release the nozzle
and unhook the nozzle
tabs from underneath the
machine to remove.
Rinse the nozzle under
warm water (max 40�C)
to remove dirt/debris.
40°C
MAX
To replace the nozzle, hook
the tabs on the base of the
nozzle under the tabs on the
base of the machine. Lower
the nozzle backwards and
push until it clicks into place.
15
Cleaning and maintenance
Removing and cleaning the brushes
Remove both tanks and tilt
the machine back.
Push the two brushbar
release buttons backwards
to unlock the brushbar.
Pull the brushbar to remove.
Clear of any debris/threads
or hair and rinse under
water to remove debris.
To replace, line up the
spindle and tabs on the back
of the spinscrub brush with
the machine and push firmly
until it clicks into place.
40°C
MAX
SCAN HERE TO GET TO
KNOW YOUR MACHINE
visit www.vax.co.uk
for help and support with
setting up your machine
16
Troubleshooting
There is an accessory missing
• Check the contents on the box to make sure the part is definitely included with your machine.
Why won't the machine turn on?
• The plug may not be fully pushed into the electrical socket.
• The fuse in the plug may need replacing. Always replace with a British 13amp fuse.
• The motor thermostat may have tripped. If this has happened, unplug the machine. Check the machine for blockages.
Why won't the machine pick up?
• The float in the dirty water tank may have been activated. Empty the dirty water tank and wait for the float to settle before
restarting your machine. See Emptying and cleaning the dirty water tank page 13.
• Check the brushbars for blockages and clear. See Removing and cleaning the brushes page 15.
• The dirty water tank and/or lid may not be fitted correctly. See Emptying and cleaning the dirty water tank page 13.
• Check the nozzle for blockages and clear. See Removing and cleaning the nozzle page 14.
• Check the nozzle is correctly fitted. See Removing and cleaning the nozzle page 14.
• The hose connector port cover may be open, close and retry. See Using the hose and tools page 11.
Why is the machine leaking solution?
• The solution tank may not be correctly fitted. Slide and push the solution tank firmly into the machine.
See Filling the solution tank page 8.
• The solution may have overflowed into the reservoir underneath the solution tank. Remove the solution tank and dry any
solution from underneath.
Why won’t the clean water/solution dispense?
• Make sure the solution and clean water tanks are fitted securely. See Filling the solution tank/Filling the clean water tank page 8.
• The trigger on the handle may not be fully pressed. See operation page 9.
• The solution or clean water tank valve may be stuck. Hold the tank over the sink and press the valve underneath to release.
• The solution or clean water tank is empty. Refill the tank. See Filling the solution tank/Filling the clean water tank page 8.
Why won’t the solution/clean water dispense when using the hose?
• Make sure the solution and clean water tank is fitted securely. See Filling the solution tank/Filling the clean water tank page 8.
• The trigger on the hose may not be fully pressed. See Using the hose and tools page 11.
• The solution or clean water tank valve may be stuck. Hold the tank over the sink and press the valve underneath to release.
• The solution or clean water tank is empty. Refill the tank. See Filling the solution tank/Filling the clean water tank page 8.
Why won’t the brushes spin?
• The brushes will only spin when the machine is reclined.
• Check the brushes are correctly fitted. See Removing and cleaning the brushes page 15.
• Check the brushes for blockages and clear. See Removing and cleaning the brushes page 15.
• Check for damage to the brushes.
WARNING: Always switch off and unplug the machine before performing any checks or maintenance.
17
Technical
Statement of Compliance: Manufacturer/EU importer: Vax Limited, hereby on our
own responsibility, declare that the VAX SpinScrub Power is manufactured in
compliance with the following Legislation:
Safety: 2014/35/EU Low Voltage Directives/Electrical Equipment (Safety)
Regulations 2016. EMC: 2014/30/EU Electromagnetic Compatibility Directive/
Electromagnetic Compatibility Regulations 2016.
Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice.
VAX is a trade mark of Techtronic Cordless GP.
© 2024 Techtronic Cordless GP. All rights reserved.
Vax Ltd, Artillery House, Heritage Way, Droitwich, WR9 8YB, UK.
Guarantee and technical
Guarantee
If a VAX machine is used in the way it is intended and it breaks down within the
guarantee period, it’s our responsibility to repair or replace it.
Here’s what isn’t covered:
• Functional parts, tools and accessories after 12 months that may suffer premature
failure due to every day wear and tear.
• Consumables after 3 months such as belts, filters, brushbars, fuses etc.
• Accidental damage.
• Cosmetic damage that does not affect the functioning of the product.
• Damage as a result of use not in accordance with the user guide.
• Damage caused by not carrying out regular maintenance.
• Damage to the power cord.
• Blockages; please refer to the user guide.
• Poor product performance caused by:
- Negligent use, misuse or careless operation of the machine.
- Failure to clean or maintain the product in accordance with the user guide.
- Use of the machine which is not in accordance with the user guide.
- Use of a VAX product for anything other than normal domestic household
purposes in the country in which it was purchased.
- Use of parts, accessories and consumables, which are not genuine VAX
components.
- Faulty installation or repairs - unless carried out by a qualified electrician
or engineer.
Making a claim?
If you wish to make a claim under your standard 1 year guarantee or extended
guarantee, please contact us on the details set out in our Vax Terms and Conditions.
18
19
Your guarantee is with Vax Limited. Please note that your statutory rights in relation to any VAX products will remain unaffected by these guarantees.
*All VAX products bought in the UK come with a standard 1 year guarantee from the date of purchase. Most VAX products are eligible for an
“Additional Guarantee” by registering with Vax. Registration within 3 months from date of purchase is required to claim the additional guarantee
and is subject to our terms and conditions (www.vax.co.uk/registration/guarantee-information)
If you need help registering, please visit www.vax.co.uk/contact.
1
What you’ll need
Grab your machine and
proof of purchase and
keep them handy.
Register
To get started scan
the QR code, or visit
vax.co.uk/registration
2
3
Bought your product direct from vax.co.uk?
Sit back and relax - your free 6 year guarantee
was automatically applied at the checkout.
Check your email for details of your guarantee
*
.
Please contact us if you haven't received this and we'll be happy to help.
Bought elsewhere?
All VAX products have a 1 year standard guarantee.
Register now to claim your additional 5 year guarantee (6 years in total).
Registering is quick and easy, just follow the steps below:
PROTECT YOUR PRODUCT FOR LONGER,
REGISTER TO ACTIVATE YOUR
FREE 6 YEAR GUARANTEE
*
Congratulations!
You’ve now secured your total 6 year
guarantee! (Keep an eye out for your
confirmation email - you'll need to keep
this safe).
V1.1
