BAUMR-AG BMCRTL00A CS3 20V SYNC Cordless Circular Saw User Manual

THE BATTERY MAY HAVE SOME CHARGE ON ARRIVAL, IT IS IMPORTANT

HOWEVER THAT THE BATTERY IS CHARGED PRIOR TO USE.

User Manual

[Revision 4.0 October 2023]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY

VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in appearance,

assembly, inclusions, specifications, description, and packaging.

CS3 Circular Saw - SYNC Series

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases, or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

• Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

• Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol, or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory, or

mental capabilities.

General Fuel Safety

• Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start, or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

• Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors, and

vents.

General Equipment Use and Care

• The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage, or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases, or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids, or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

CS3 Circular Saw - SYNC Series

General Electrical Safety

• Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Wherever possible, use a residual current

device (RCD).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

• Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

• The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Child Choking Hazard!

• WARNING: CHOKING HAZARD - CHILDREN UNDER 8 YRS. CAN CHOKE OR SUFFOCATE ON SMALL PARTS. ADULT

SUPERVISION REQUIRED.

• Carefully inspect anything a baby or child could gain access to, including this product & packaging.

• Dangers include anything of a size that could become stuck or lodged in a baby or child's airway.

• Dangers include things like raw, hard fruit and vegetable pieces, large pieces of meat, bones or sausage skins, popcorn, nuts,

hard lollies and corn chips, small magnets and batteries, coins, beads, marbles and small uninflated balloons, broken toys and smaller toys,

buttons, keys, and coins. But there are also many more.

• Pay particular attention to accessories, nuts, bolts, screws, washers, caps, covers, loose parts, parts that could be removed or break off, pieces

of packaging, staples, tape etc.

• In the case of any doubt, secure the item of concern in an appropriate manner, or completely remove the possibility of access by a baby or child.

Warning: Button Battery Included

IF SWALLOWED THE BATTERY CAN CAUSE SEVERE OR FATAL INJURY IN 2 HOURS OR LESS. DO NOT SWALLOW OR

PLACE INSIDE ANY PART OF THE BODY. MEDICAL ATTENTION SHOULD BE SOUGHT IMMEDIATELY IF IT IS SUSPECTED

THE BATTERY HAS BEEN SWALLOWED OR PLACED INSIDE ANY PART OF THE BODY.

Important Safety Reminders

• BE AWARE THAT THE EQUIPMENT MAY INCLUDE HAZARDOUS COMPONENTS, SUCH AS BLADES, HOT SURFACES AND MOVING

PARTS.

• MOVING BLADES CAN CAUSE SERIOUS INJURY AND EVEN DEATH IF USED IMPROPERLY OR WITHOUT SUFFICIENT PPE.

• DO NOT USE THIS EQUIPMENT ON UNEVEN SURFACES AND ALWAYS MAINTAIN GOOD BALANCE WHEN USING THIS EQUIPMENT.

FAILURE TO DO SO MAY CAUSE SERIOUS INJURY.

• MAINTAIN A SECURE GRIP OF THE TRIGGER ASSEMBLY AT ALL TIMES.

• Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

• Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool

or battery-operated (cordless) power tool.

Work Area Safety

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical Safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed(grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

CS3 Circular Saw - SYNC Series

• Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase the risk of electric shock.

• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

• If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces

the risk of electric shock.

• Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch is in the OFF position before connecting to power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Always keep proper footing and balance. This enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust

collection can reduce dust-related hazards.

• Do not wear loose clothing or jewellery. Contain longhair. Loose clothes, jewellery, or long hair can be drawn into air vents.

• Do not use on a ladder or unstable support. Stable footing on a solid surface enables better control of the power tool in unexpected situations.

Power Tool Use and Care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for

which it was designed.

• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or

storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories, and tool bits etc.in accordance with these instructions, considering the working conditions and the work to be

performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Battery Tool Use and Care

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire

when used with another battery pack.

• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects,

that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts

eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

Service

• Have your power tool serviced by a qualified repairperson using only identical replacement parts. This will ensure that the safety of the power tool

is maintained.

• When servicing a power tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of

unauthorized parts or failure to follow Maintenance instructions may create a risk of shock or injury.

Cutting Procedures

DANGER! KEEP HANDS AWAY FROM CUTTING AREA AND THE BLADE. KEEP YOUR SECOND HAND ON AUXILIARY HANDLE, OR

MOTOR HOUSING. IF BOTH HANDS ARE HOLDING THE SAW, THEY CANNOT BE CUT BY THE BLADE.

• Do not reach underneath the workpiece. The guard cannot protect you from the blade below the workpiece.

• Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth should be visible below the workpiece.

• Never hold piece being cut in your hands or across your leg. Secure the workpiece to a stable platform. It is important to support the work

properly to minimize body exposure, blade binding, or loss of control.

• Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting tool may contact hidden wiring. Contact

with a “live” wire will also make exposed metal parts of the power tool “live” and could give the operator an electric shock.

• When ripping, always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance of blade-binding.

• Always use blades with correct size and shape.

• Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially designed for your saw, for optimum

performance and safety of operation.

Kickback Causes and Related Warnings

• Kickback is a sudden reaction to a pinched, bound, or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece

toward the operator.

• When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward

the operator.

CS3 Circular Saw - SYNC Series

• If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the

blade to climb out of the kerf and jump back toward the operator.

• Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as

given below:

• Maintain a firm grip with both hands on the saw and position your arms to resist kickback forces. Position your body to either side of the blade,

but not in line with the blade. Kickback could cause the saw to jump backwards, but kickback forces can be controlled by the operator, if proper

precautions are taken.

• When blade is binding, or when interrupting a cut for complete stop. Never attempt to remove the saw from the work or pull the saw backward

while the blade is in motion or kickback may occur. Investigate and take corrective actions to eliminate the cause of blade binding.

• When restarting a saw in the workpiece, centre the saw blade in the kerf and check that saw teeth are not engaged into the material. If saw blade

is binding, it may walk up or kickback from the workpiece as the saw is restarted.

• Support large panels to minimise the risk of blade pinching and kickback. Large panels tend to sag under their own weight. Supports must be

placed under the panel on both sides, near the line of cut and near the edge of the panel.

• Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and

kickback.

• Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause

binding and kickback.

• Use extra caution when sawing into existing walls or other blind areas. The protruding blade may cut objects that can cause kickback.

Lower Guard Function

• Check lower guard for proper closing before each use. Do not operate the saw if lower guard does not move freely and close instantly. Never

clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower guard with the

retracting handle and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut.

• Check the operation of the lower guard spring. If the guard and the spring are not operating properly, they must be serviced before use. Lower

guard may operate sluggishly due to damaged parts, gummy deposits, or a build-up of debris.

• Lower guard should be retracted manually only for special cuts such as “plunge cuts” and “compound cuts.” Raise lower guard by retracting

handle and as soon as blade enters the material, the lower guard must be released. For all other sawing, the lower guard should operate

automatically.

• Always observe that the lower guard is covering the blade before placing saw down on bench or floor.

Additional Safety Warnings

• Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is

unstable and may lead to loss of control.

• Always wear eye protection with side shields marked to comply with ANSI Z87.1 when assembling parts, operating the tool, or performing

maintenance. Following this rule will reduce the risk of serious personal injury.

• Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule will reduce the risk of serious personal injury.

• Protect your hearing. Wear hearing protection during extended periods of operation. Following this rule will reduce the risk of serious personal

injury.

• Battery tools do not have to be plugged into an electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards

when not using your battery tool or when changing accessories. Following this rule will reduce the risk of electric shock, fire, or serious personal

injury.

• Do not place battery tools or their batteries near fire or heat. This will reduce the risk of explosion and possibly injury.

• Do not crush, drop, or damage battery pack. Do not use a battery pack or charger that has been dropped or received a sharp blow. A damaged

battery is subject to explosion. Properly dispose of a dropped or damaged battery immediately.

• Batteries can explode in the presence of a source of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any

cordless product in the presence of open flame. An exploded battery can propel debris and chemicals. If exposed, flush with water immediately.

• Do not charge battery tool in a damp or wet location. Following this rule will reduce the risk of electric shock.

• For best results, your battery tool should be charged in a location where the temperature is more than 50°F but less than 100°F. To reduce the

risk of serious personal injury, do not store outside or in vehicles.

• Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with your skin, wash immediately with

soap and water. If liquid gets into eyes, flush them with clean water for at least 10 minutes, then seek immediate medical attention. Following this

rule will reduce the risk of serious personal injury.

CS3 Circular Saw - SYNC Series

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases, or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases, or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing, and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

CS3 Circular Saw - SYNC Series

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp, or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

CS3 Circular Saw - SYNC Series

Table of Contents

Safety ............................................................................................................................................................. 2

Safety Symbols ........................................................................................................................................................... 6

Parts Identification ....................................................................................................................................... 9

Assembly ..................................................................................................................................................... 10

Unpacking ................................................................................................................................................................. 10

Attaching the Blade ................................................................................................................................................... 11

Removing The Blade ................................................................................................................................................ 13

Operation ..................................................................................................................................................... 14

Applications .............................................................................................................................................................. 14

Installing/Removing the Battery Pack ....................................................................................................................... 14

Kickback ................................................................................................................................................................... 15

Saw Blades ............................................................................................................................................................... 16

Blade Guard System................................................................................................................................................. 17

Starting/Stopping the Saw ........................................................................................................................................ 18

Lock-OFF Button ...................................................................................................................................................... 19

Adjusting the Blade Depth ........................................................................................................................................ 20

Operating the Saw .................................................................................................................................................... 20

Cross Cutting/Rip Cutting ......................................................................................................................................... 21

Rip Cutting ................................................................................................................................................................ 22

Cut Scale Width ........................................................................................................................................................ 23

Bevel Cutting ............................................................................................................................................................ 24

Adjusting the Bevel Setting ....................................................................................................................................... 24

Making A Bevel Cut .................................................................................................................................................. 25

Pocket Cutting .......................................................................................................................................................... 25

Lithium Battery Care and Maintenance .................................................................................................... 28

Top 3 Battery Care Requirements ............................................................................................................................ 28

Adjustments ................................................................................................................................................ 29

0° Bevel Stop ............................................................................................................................................................ 29

Checking 0° Bevel Stop ............................................................................................................................................ 29

Specifications ............................................................................................................................................. 30

CS3 Circular Saw - SYNC Series

Parts Identification

No. Name

A Lock-OFF button

B Switch trigger

C

Blade wrench storage

D

Area depth lock lever

E

Cut width scale

F

Bevel lock knob

G

Work light

E

F

G

C

D

B

A

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Assembly

WARNING: BUTTON BATTERY INCLUDED. IF SWALLOWED THE BATTERY CAN CAUSE

SEVERE OR FATAL INJURY IN 2 HOURS OR LESS. DO NOT SWALLOW OR PLACE INSIDE

ANY PART OF THE BODY. MEDICAL ATTENTION SHOULD BE SOUGHT IMMEDIATELY IF IT

IS SUSPECTED THE BATTERY HAS BEEN SWALLOWED OR PLACED INSIDE ANY PART OF

THE BODY.

Unpacking

This product requires assembly. Carefully remove the product and any accessories from the box. All items listed

in the Includes section must be included at the time of purchase.

WARNING! Items in this Assembly section are not assembled to the product by the manufacturer

and require customer installation. Use of a product that may have been improperly assembled

could result in serious personal injury.

•

Inspect the product carefully to make sure no breakage or damage occurred during shipping.

•

Do not discard the packing material until you have carefully inspected and satisfactorily operated the

product.

WARNING! If any parts are damaged or missing do not operate this product until the parts are

replaced. Use of this product with damaged or missing parts could result in serious personal

injury.

WARNING! Do not attempt to modify this product or create accessories not recommended for use with

this product. Any such alteration or modification is misuse and could result in a hazardous condition

leading to possible serious personal injury.

WARNING! To prevent accidental starting that could cause serious personal injury, always remove the

battery pack from the product when assembling parts.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Attaching the Blade

WARNING! A 7-1/4 in. blade is the maximum blade capacity of the saw. Never use a blade that is

too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will

come in contact with the blade guard, while thicker blades will prevent blade screw from securing blade

on spindle. Either of these situations could result in a serious accident.

1. Remove the battery pack from the saw.

2. Remove the blade wrench (6mm hex key) from the storage area.

3. Depress the spindle lock button and remove the blade screw and outer blade washer.

NOTE: Turn the blade screw clockwise to remove. To prevent damage to the spindle or spindle lock, always

allow motor to come to a complete stop before engaging spindle lock. Do not run the circular saw with

spindle lock engaged.

4. Wipe a drop of oil onto the inner blade washer and outer blade washer where they contact the blade.

A: Spindle lock button

B: Lower blade guard handle

C: Spindle

D: Blade

E: Blade screw

F: Outer blade washer

G:

Inner blade washer

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

WARNING! If inner blade washer has been removed, replace it before placing blade on spindle.

Failure to do so could cause an accident since blade will not tighten properly.

5. Fit the saw blade inside the lower blade guard and onto the spindle.

NOTE: The saw teeth point upward at the front of the saw.

6. Replace the outer blade washer.

7. Depress the spindle lock button, then replace the blade screw. Tighten the blade screw securely by turning it

anti-clockwise.

8. Return the blade wrench to the storage area.

NOTE: Never use a blade that is too thick to allow the outer blade washer to engage with the flats on the

spindle.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Removing The Blade

1. Remove the battery pack from the saw.

2. Remove the blade wrench from the storage area.

3. Position the saw as shown, depress the spindle lock button, and remove the blade screw by turning it

clockwise.

4. Remove the outer blade washer.

5. Remove the blade.

A: Spindle lock

B: Lower blade lever guard

C: Blade screw

D: To loosen

E: To tighten

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Operation

WARNING!  Do not allow familiarity with products to make you careless. Remember that a

careless fraction of a second is sufficient to inflict serious injury.  Always wear eye protection

with side shields marked to comply with ANSI Z87.1. Failure to do so could result in objects being

thrown into your eyes resulting in possible serious injury.  Do not use any attachments or accessories

not recommended by the manufacturer of this product. The use of attachments or accessories not

recommended can result in serious personal injury.  Never use abrasive cut-off wheels of any kind with

this saw. Use of non-wood cutting blades can result in property damage or serious personal injury.

Applications

You may use this product for the purposes listed below:

•

Cutting all types of wood products (lumber, plywood, paneling, composition board, and hard wood)

Installing/Removing the Battery Pack

1. Insert the battery pack into the product, as shown.

2. Make sure the latches on each side of the battery pack snap in place and that battery pack is secured in the

product before beginning operation.

3. Depress the latches to remove the battery pack.

For complete charging instructions, see the operator’s manual for your battery pack and charger.

WARNING! Battery tools are always in operating condition. Switch should always be locked

when not in use or carrying at your side.

A: Depress latches

to remove battery

pack

B: Battery pack

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Kickback

Kickback: blade set too deep

Incorrect support Correct support

Correct blade depth setting:

blade exposed 1/4in. (6.35mm) or

less on underside of workpiece

Kickback occurs when the blade stalls rapidly and the saw is driven back towards you. Blade stalling is caused

by any action which pinches the blade in the wood.

DANGER! Release switch immediately if blade binds or saw stalls. Kickback could cause you to

lose control of the saw. Loss of control can lead to serious injury.

To guard against kickback, avoid dangerous practices such as the following:

•

Setting blade depth incorrectly.

•

Sawing into knots or nails in workpiece.

•

Twisting the blade while making a cut.

•

Making a cut with a dull, gummed up, or improperly set blade.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

•

Supporting the workpiece incorrectly.

•

Forcing a cut.

•

Cutting warped or wet lumber.

•

Operating the tool incorrectly or misusing the tool.

To lessen the chance of kickback, follow these safety practices:

•

Keep the blade at the correct depth setting. The depth setting should not exceed 1/4 in. below the material

being cut.

•

Inspect the workpiece for knots or nails before cutting. Never saw into a knot or nail.

•

Make straight cuts. Always use a straight edge guide when rip cutting. This helps prevent twisting the blade.

•

Use clean, sharp, and properly set blades. Never make cuts with dull blades.

•

Support the workpiece properly before beginning a cut.

•

Use steady, even pressure when making a cut. Never force a cut.

•

Do not cut warped or wet lumber.

•

Hold the saw firmly with both hands and keep your body in a balanced position so as to resist the forces if

kickback should occur.

WARNING! When using the saw, always stay alert and exercise control. Do not remove the saw

from the workpiece while the blade is moving.

Saw Blades

The best of saw blades will not cut efficiently if they are not kept clean, sharp, and properly set. Using a dull

blade will place a heavy load on the saw and increase the danger of kickback. Keep extra blades on hand, so

that sharp blades are always available.

Gum and wood pitch hardened on blades will slow the saw down. Remove saw blade from the saw and use gum

and pitch remover, hot water, or kerosene to remove these accumulations. DO NOT USE GASOLINE.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Blade Guard System

The lower blade guard attached to the circular saw is there for your protection and safety. Do not alter it for any

reason. If it becomes damaged, do not operate the saw until you have the guard repaired or replaced. Always

leave guard in operating position when using the saw.

DANGER! When sawing through work, lower blade guard does not cover blade on the underside

of work. Since blade is exposed on underside of work, keep hands and fingers away from cutting

area. Any part of your body coming in contact with moving blade will result in serious injury.

CAUTION! Never use saw when guard is not operating correctly. Check the guard for correct operation

before each use. The guard is operating correctly when it moves freely and readily returns to the closed

position. If you drop the saw, check the lower blade guard and bumper for damage at all depth settings

before reuse.

A: Lower blade guard is in UP

position when making a cut

B: Blade exposed on

underside of workpiece

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Starting/Stopping the Saw

This saw is equipped with a work light that will turn on when the trigger is depressed and will turn OFF when the

trigger is released.

To start the saw:

1. Depress the lock-off button.

2. Depress the switch trigger.

Always let the blade reach full speed, then guide the saw into the workpiece.

WARNING! The blade coming in contact with the workpiece before it reaches full speed could

cause the saw to “kickback” towards you resulting in serious injury.

To stop the saw:

•

Release the switch trigger.

After you release the switch trigger, allow the blade to come to a complete stop. Do not remove the saw from the

workpiece while the blade is moving.

A: Lock-OFF button

B: Switch trigger

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Lock-OFF Button

The lock-off button reduces the possibility of accidental starting. The lock-off button is located on the handle

above the switch trigger. The lock-off button must be depressed before you pull the switch trigger. The lock

resets each time the trigger is released.

NOTE: You can depress the lock-off button from either the left or right side.

A: Lock-OFF button

B: Switch trigger

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Adjusting the Blade Depth

Always keep correct blade depth setting. The correct blade depth setting for all cuts should not exceed 1/4 in.

below the material being cut. More blade depth will increase the chance of kickback and cause the cut to be

rough. For more depth of cut accuracy, a scale is located on the upper blade guard.

•

Loosen the depth lock lever by lifting it upward away from the base.

•

Determine the desired depth of cut.

•

Locate the depth of cut scale on the back of the upper blade guard.

•

Hold the base flat against the workpiece and raise or lower the saw until the indicator mark on bracket aligns

with the notch on the blade guard.

•

Tighten the depth lock lever securely by pushing it downward toward the base.

Operating the Saw

A: Depth lock lever

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

WARNING! To make sawing easier and safer, always maintain proper control of the saw. Loss of

control could cause an accident resulting in possible serious injury.

To make the best possible cut, follow these helpful hints.

•

Hold the saw firmly with both hands.

•

Avoid placing your hand on the workpiece while making a cut.

•

Support the workpiece so that the cut (kerf) is always to your side.

•

Support the workpiece near the cut.

•

Use clamps or other practical ways to secure the workpiece so that the workpiece will not move during the

cut.

•

Always place the saw on the workpiece that is supported, not the “cut off” piece.

•

Place the workpiece with the “good” side down.

•

Draw a guideline along the desired line of cut before beginning your cut.

Cross Cutting/Rip Cutting

•

When making a straight cross cut or rip cut, align the line of cut with the ‘00’ blade guide notch on the base.

•

Since blade thicknesses vary, always make a trial cut in scrap material along a guideline to determine how

much, if any, you must offset the guideline to produce an accurate cut.

NOTE: The distance from the line of cut to the guideline is the amount you should offset the guide.

A: 45°blade guide notch

B: Guidelines

C: 0º blade guide notch

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Rip Cutting

Use a guide when making long or wide rip cuts with the saw.

1. Secure the workpiece.

2. Clamp a straight edge to the workpiece using C-clamps.

3. Saw along the straight edge to achieve a straight rip.

NOTE: Do not bind the blade in the cut.

A: Straight edge

B: Workpiece

C:

C-Clamp

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Cut Scale Width

The cut scale width is located on the base of the saw. When making straight cross cuts or rip cuts, the scale can

be used to measure up to 4-1/2 in. on the right side of the blade, and up to 1 in. on the left side of the blade.

A: Cut scale width

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Bevel Cutting

1. Adjust the angle of the cut to any desired setting between zero and 56°. Refer to Adjusting the Bevel Setting

next.

2. If making a 45° bevel cut, align the line of cut with the 45° blade guide notch on the base.

3. Make a trial cut in scrap material along a guideline to determine how much you should offset the guideline.

Adjusting the Bevel Setting

1. Loosen the bevel lock knob.

2. Raise the motor housing end of the saw until you reach the desired angle setting on the bevel scale.

3. Tighten the bevel lock knob securely.

WARNING! Attempting a bevel cut without having the bevel lock knob securely tightened can

result in serious injury.

NOTE: For bevel cuts 56° and above, move the bevel lock knob into the notch at the 56° mark on the bevel

scale, and tighten the knob securely.

A: Bevel lock knob

B: Bevel scale

C: 45° blade guide notch

D:

Guidelines

A: Motor housing

B: Bevel scale

C: Bevel lock knob

D:

Notch

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Making A Bevel Cut

1. Hold the saw firmly with both hands as shown.

2. Rest the front edge of the base on the workpiece.

3. Start the saw and let the blade reach full speed.

4. Guide the saw into the workpiece and make the cut.

5. Release the trigger and allow the blade to come to a complete stop.

6. Lift the saw from the workpiece.

Pocket Cutting

WARNING! Always adjust bevel setting to zero before making a pocket cut. Attempting a pocket

cut at any other setting can result in loss of control of the saw possibly causing serious injury.

1. Adjust the bevel setting to zero.

2. Set the blade to the correct blade depth setting.

3. Swing the lower blade guard up using the lower blade guard handle.

NOTE: Always raise the lower blade guard with the handle to avoid serious injury.

4. Hold the lower blade guard by the handle.

A: Lower blade guard handle

B: Pocket cut

C: Lower blade guard

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

WARNING! Never extend your fingers while holding the lower blade guard handle. Extending

your fingers may result in contact with the blade, causing serious injury.

5. Rest the front of the base flat against the workpiece with the rear of the handle raised so the blade does not

touch the workpiece.

6. Start the saw and let the blade reach full speed.

7. Guide the saw into the workpiece and make the cut.

WARNING! Always cut in a forward direction when pocket cutting. Cutting in the reverse

direction could cause the saw to climb up on the workpiece and back toward you.

8. Release the trigger and allow the blade to come to a complete stop.

9. Lift the saw from the workpiece.

10. Clear corners out with a hand or sabre saw.

WARNING! Never tie the lower blade guard in a raised position. Leaving the blade exposed could

lead to serious injury.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Lithium Battery Care and Maintenance

Top 3 Battery Care Requirements

1. Charge battery before first use. The battery may arrive with some charge, regardless of this the

battery must be charged on the initial charge and for each subsequent charge.

2. Charge battery immediately when it is depleted. Do not store a depleted battery. This will

permanently impact the life of the battery. If the battery is going to be stored for a period of time, fully

charge the battery before storing.

3. Disconnect battery when not in use. To prolong the life of a battery, disconnect it from the unit

when not in use. Disconnect chargers from the battery once charged.

To ensure the battery maintains optimum performance, follow the guidelines outlined below.

•

For best results, charge batteries in temperatures between 10°C and 30°C

•

When battery is charged, disconnect the charger from the power supply and remove the battery from the

charger.

•

If a battery is stored or otherwise unused for an extended period, and the battery has no charge remaining

when you check it, consider it to be damaged. Do not attempt to recharge it or to use it. Replace it with a

new battery.

•

Use only with the battery charger specified by the manufacturer.

•

Ensure that the battery charger electrical cord is not subjected to damage or stress. Do not operate the

battery charger if it has a damaged electrical cord or plug.

•

Do not use the charger in wet areas or expose it to rain or water.

•

The typical estimated life of a Lithium-Ion battery is about two to three years or 300 to 500 charge cycles,

whichever occurs first. One charge cycle is a period of use from fully charged, to fully discharged, and fully

recharged again

•

Explosion hazard – protect the battery against heat, for example, direct sunlight and fire. Do not store

batteries in vehicles or locations subject to heat.

•

Batteries can explode in the presence of an ignition source, such as a pilot light. To reduce the risk of

serious personal injury, never use any cordless product in the presence of open ﬂame. Exploding batteries

can propel debris and chemicals.

•

Do not open the battery – danger of short-circuiting and/or explosion.

•

Do not attempt to destroy or disassemble the battery pack or remove any of its components.

•

Do not touch the battery terminals with metal objects and/or body parts as short-circuit and/or personal injury

may result.

•

Explosion hazard – do not open and/or short-circuit the battery.

•

Poison hazard – battery leakage (liquid ejection). Under extreme conditions, liquid may be ejected from the

battery – avoid contact. If contact accidentally occurs, immediately seek medical attention, and flush with

water. If liquid contacts eyes, immediately seek medical attention, flush with clean water for at least 10

minutes. Liquid ejected from the battery may cause irritation or burns.

•

Dispose of non-serviceable batteries in an environmentally responsible manner and according to local

regulations.

Failure to adhere to the requirements above may result in the battery becoming inoperative or battery life being

reduced. In extreme cases or abuse, battery overheating or fire may result.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Adjustments

WARNING! To prevent accidental starting that could cause serious personal injury, always

remove the battery pack from the product when making adjustments.

0° Bevel Stop

The saw has a 0° bevel stop that has been factory adjusted to assure 0° angle of the saw blade plate when

making 90° cuts.

Checking 0° Bevel Stop

1. Remove battery pack.

2. Place the saw in an upside-down position on a workbench.

3. Check the squareness of the saw blade plate to the base of the saw using a carpenter’s square.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CS3 Circular Saw - SYNC Series

Specifications

Input Voltage 20V

Blade Diameter 165mm

Max Cutting Depth 55mm @ 90° ,39mm @ 45°

No Load Speed 4200RPM

Bevel Adjustment Up to 45°

Adjustable Blade Depth 55mm

Electric Blade Brake Yes

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging,

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear, or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear, or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business,

or employee, or financially affect the user, business, or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement, or service by a

technician may cause financial loss, loss of employee

time or an inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

ideas, diagrams, or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning, or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

BAUMR-AG BMCRTL00A CS3 20V SYNC Cordless Circular Saw

Product's Documents

Product manual

Specifications

BAUMR-AG BMCRTL00A Questions and Answers