Loading ...
Loading ...
Loading ...
Version 23.00, November 2020
Rohde & Schwarz R&S
®
RTH1002, R&S
®
RTH1004 Handheld Oscilloscope 5
Base unit
Vertical system
Input channels
R&S
®
RTH1002
2 oscilloscope channels, 1 multimeter
R&S
®
RTH1004
4 oscilloscope channels
All inputs are floating and fully isolated in line with CAT IV 600 V, CAT III 1000 V safety
rating. See figure regarding isolation rating on page 14.
Input impedance
1 MΩ ± 1 % || 12 pF ± 2 pF (meas.)
Analog bandwidth (–3 dB)
R&S
®
RTH1002 and R&S
®
RTH1004
≥ 60 MHz
R&S
®
RTH1002 with -B221 option and
R&S
®
RTH1004 with -B241 option
≥ 100 MHz
R&S
®
RTH1002 with -B222 option and
R&S
®
RTH1004 with -B242 option
≥ 200 MHz
R&S
®
RTH1002 with -B223 option and
R&S
®
RTH1004 with -B243 option
≥ 350 MHz
1
R&S
®
RTH1002 with -B224 option and
R&S
®
RTH1004 with -B244 option
≥ 500 MHz
1
Measurement of analog bandwidth at input sensitivities ≥ 20 V/div is limited by input
voltage rating versus frequency, see figure “Input rating: Maximum signal voltage at
oscilloscope input” on page 14.
Lower frequency limit (–3 dB) at
AC coupling
< 8 Hz (meas.)
Bandwidth limits
1/2/5/10/20/50/100/200/500 kHz,
1/2/5/10/20/50 MHz
only with R&S
®
RTH-B222, -B242, -B223,
-B243, -B224, -B244 options
100 MHz
only with R&S
®
RTH-B223, -B243, -B224,
-B244 options
200 MHz
Rise time (calculated)
R&S
®
RTH1002 and R&S
®
RTH1004
< 5.8 ns
R&S
®
RTH1002 with -B221 option and
R&S
®
RTH1004 with -B241 option
< 3.5 ns
R&S
®
RTH1002 with -B222 option and
R&S
®
RTH1004 with -B242 option
< 1.75 ns
R&S
®
RTH1002 with -B223 option and
R&S
®
RTH1004 with -B243 option
< 1 ns
2
R&S
®
RTH1002 with -B224 option and
R&S
®
RTH1004 with -B244 option
< 700 ps
2
ADC resolution
10 bit
Vertical resolution of overall system
9 bit; up to 16 bit with high resolution
decimation
DC gain accuracy
offset and position set to zero, after self-alignment
input sensitivity > 5 mV/div
±1.5 %
input sensitivity > 2 mV/div to 5 mV/div
±2 %
input sensitivity 2 mV/div
±2.5 %
Input coupling
DC, AC
Input sensitivity
in steps of 1, 2, 4, 5 in each decade
2 mV/div to 100 V/div
Maximum input voltage
at BNC inputs
CAT IV 300 V (RMS), 424 V (peak),
derates at 20 dB/decade to 5 V (RMS)
above 500 kHz (see figure “Input rating:
Maximum signal voltage at oscilloscope
input” on page 14)
with R&S
®
RT-ZI10 or R&S
®
RT-ZI11 probe
CAT IV 600 V, CAT III 1000 V,
derating in line with probe specification
Position range
±4 div
Invert
R&S
®
RTH1004
CH1, CH2, CH3, CH4
R&S
®
RTH1002
CH1, CH2
Offset range
input sensitivity
≥ 40 V/div
0
≥ 1 V/div to ≤ 20 V/div
±200 V
≤ 500 mV/div
±4 V
1
≥ 200 MHz (meas.) for input sensitivities ≥ 20 V/div.
2
< 1.75 ns (calculated) for input sensitivities ≥ 20 V/div.
Loading ...
Loading ...
Loading ...