This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
‐Reorient or relocate the receiving antenna.
‐Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
‐Consult the dealer or an experienced radio/TV technician for help important announce-
ment.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Pairing with Third Reality
Pairing steps:
App: Third Reality App
Hub: Third Reality Smart Hub/Smart Hub Gen2 Plus
Register and sign in your THIRDREALITY account, and add the THIRDREALITY hub.
Long press the button of the switch for 30 seconds until the LED turns fast blinking,
make sure it is in pairing mode.
Tab "+" in the right of Smart Hub to add device.
Create routines to control other connected devices.
1)
2）
3）
4)
Pairing with Amazon Echo
Pairing steps:
Hub: Echo speakers with built-in Zigbee hub, Echo 4th Gen, Echo Plus 1st & 2nd Gen,
Echo Studio
App: Amazon Alexa
Ask Alexa to check for updates before pairing.
Long press the button of the switch for 30 seconds until the LED turns fast blinking,
make sure it is in pairing mode.
Tab "+" in the Alexa App, choose "Zigbee" and "others" to add device.
You can create routines with the device.
1)
2）
3）
4)
Pairing with SmartThings
Pairing steps:
App: SmartThings App
Devices: SmartThings Hub 2nd Gen(2015) and 3rd Gen.(2018), Aeotec Smart Home Hub.
Check for updates to make sure the SmartThings Hub firmware is up to date before
pairing.
Long press the button of the switch for 30 seconds until the LED turns fast blinking,
make sure it is in pairing mode.
Open the SmartThings App, tap “+” on the upper right corner to ”Add device” and
then tap “Scan” to “Scan for nearby devices”.
The device will be paired with the SmartThings hub in a few seconds.
Create routines to control connected devices.
1)
2）
3）
4)
5)
Open this link in your PC browser.
https://bestow-regional.api.smartthings.com/invite/adMKr50EXzj9
Log in your SmartThings Account.
Click “Enroll” --“Available Drivers” -- “Install” to install the device driver as needed.
1)
2）
3）
Reboot your SmartThings hub by powering it off and power it on again.
“Scan for Nearby Devices” in SmartThings App to pair the THIRDRELAITY devices
with your SmartThings hub.
You can change the driver of the Light in SmartThings App.
4)
5）
6）
Pairing with Hubitat
Pairing steps:
App: Third Reality App
Hub: Third Reality Smart Hub
Tab "Add Device" in Hubitat Devices page.
Long press the button of the switch for 30 seconds until the LED turns fast blinking，
make sure it is in pairing mode.
Choose "Zigbee", then "Start Zigbee Pairing".
Create a device name and room name, click "Next" to complete pairing.
1)
2）
4)
5)
Pairing with Home Assistant ZHA
Pairing steps:
Long press the button of the switch for 30 seconds until the LED turns fast blinking，
make sure it is in pairing mode.
Make sure Home Assistant Integrations Zigbee Home Automation Setup is ready,
then go to “Configuration” page, click “integration”.
Click “Devices” on the Zigbee item, the click “Add Devices”.
After the pairing is completed, it will show up in the page.
Back to “Devices” page, then you can find the device dded.
Click to enter in the control interface to set the device.
Click “+” belongs to Automation and then you can add different actions.
1)
2）
3）
4）
5）
6）
7）
How to add SmartThings drivers for
Third Reality Smart Switch Gen3
