GENPOWER GENPINGPRA5M0-X2 2 x 2200W Portable Power Generator User Manual

User Manual

[Revision 8.0 December 2023]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND

MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in

appearance, assembly, inclusions, specifications, description, and packaging.

The product is NOT supplied with engine oil, although traces of oil from the manufacturing process may be present. It is essential to add

adequate engine oil of the correct type to the engine before use. Failure to add engine oil will void the product warranty.

SV5000 Inverter Generator

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

• Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

• Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory or

mental capabilities.

General Fuel Safety

• Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

• Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors and

vents.

General Equipment Use and Care

• The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

General Electrical Safety

• Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Always use a Residual Current Device

(RCD) (GFCI) / Earth Leakage Circuit

Breaker / Safety Switch when operating this

item (electrical items only).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

• Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

• The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Inverter Generator Safety

• The supplier cannot anticipate every possible hazardous circumstance that the user may encounter. The warnings in this manual, on tags, and on

affixed decals are not all-inclusive. To avoid accidents, the user must understand and follow all manual instruction and use common sense.

WARNING!

• Read and understand this manual in its entirety before operating this generator. Improper use of this generator could result in serious

injury or death.

• Do not operate indoors or in a confined space that prevents dangerous carbon monoxide gas from dissipating.

• Using a generator indoors WILL KILL YOU IN MINUTES!

• Carbon monoxide gas is a poisonous, odorless gas that can cause headache, confusion, fatigue, nausea, fainting, sickness, seizures, or

death. If you start to experience any of these symptoms, IMMEDIATELY get fresh air and seek medical attention.

• Never use indoors, in a covered area, or in a confined space, even if doors and windows are open.

• Install a battery-operated carbon monoxide alarm near bedrooms.

• Keep exhaust from this unit from entering a confined area through windows, doors, vents, or other openings.

• When working in areas where vapours could be inhaled, use a respirator mask according to all of its instructions.

• Engine exhaust contains chemicals that lead to cancer and cause birth defects.

• Always wash hands after handling generator.

• Never exceed generators wattage / amperage capacity. This could damage the generator and / or connected electrical devices.

• Check operating voltage and frequency requirements of all electrical devices prior to plugging them into the generator.

• Never start or stop engine with electrical devices plugged in to the receptacles. Failure to do so could damage the generator and / or

connected electrical devices.

• Always start the engine and let it stabilize before connecting any electronic devices.

• Disconnect all electronic devices before stopping the engine.

• Starter and other moving parts can catch on clothing, jewellery, and hair.

• Do not wear loose clothing or gloves.

• Remove jewellery or anything else that could be caught in moving parts.

• Tie back or wear protective head covering to contain long hair.

• Keep engine away from flammable objects and other hazardous materials.

• The fuel and its vapours used to power this unit are highly flammable and could explode resulting in serious injury or death.

• Never fill or drain fuel tank indoors.

• Never overfill fuel tank. If fuel spills, move the unit at least 30 feet away from the spill and wipe up any remaining fuel on the unit before starting

the engine.

• Never smoke while operating or fuelling this unit.

• Never operate or store this unit near an open flame, heat, or any other ignition source.

• Generator should have at least 5 feet of clearance from buildings or other equipment during operation.

• Keep engine free of grass, leaves, or grease which are flammable.

• When adding or draining fuel, unit should be turned off for at least 2 minutes to cool before removing fuel cap. If unit has been running then the

fuel cap is under pressure, remove slowly.

• To keep fuel from spilling, secure unit so it cannot tip while operating or transporting.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

• When transporting unit, disconnect the spark plug wire and make sure the fuel tank is empty with the 3 in 1 switch is turned to the off position.

• Pull cord recoils rapidly and pulls arm towards engine faster than you can let go which could result in injury.

• To avoid recoil, pull starter cord slowly until resistance is felt, then pull rapidly.

• Avoid contacting hot areas of this unit.

• Use caution around the muffler, cylinder, and other engine parts as they can be extremely hot.

• Allow hot components to cool before touching.

• This generator produces a very high voltage which could result in burn or electrocution causing serious injury or death.

• Never handle the generator, electronic devices, or any cord while standing in water, while barefoot, or when hands or feet are wet.

• Always keep the generator dry. Never operate generator in rain or under wet conditions.

• Use a ground fault circuit interrupter (GFCI or RCD) in a damp or highly conductive area, such as metal decking or steel work.

• Never plug electronic devices into generator having frayed, worn, or bare wires. Never touch bare wires or make contact with receptacles.

• Never permit a child or unqualified person to operate generator. Keep children a minimum of 10 feet away from the generator at all times.

• If using the generator for back-up power, notify your local utility company.

• If connecting generator to a building's electrical system for standby power, you must use a qualified electrician to install a transfer switch.

Failure to isolate the generator from the power utility could result in serious injury or death to electric utility workers.

• Generator must be properly grounded to prevent electrocution.

• Only operate generator on a level surface.

• Always connect the nut and ground terminal on the frame to an appropriate ground source.

• Never modify this unit in any way or modify governed speed.

• Increasing governing speed is dangerous which can result in personal injury and / or damaged equipment.

• Decreasing governing speed adds an excessive load and can damage equipment.

• Only when operating at the pre-set governing speed will this generator supply the correct rated frequency and voltage.

• Only use this unit as it is intended, or serious injury or death could result.

• Do not bypass any safety device. Moving parts are covered with guards. Make sure all protective covers are in place.

• Never transport or make adjustments to this unit while it is running.

• Never insert objects through cooling slots.

• Never operate this unit if there are any broken or missing parts and only use supplier-approved replacement parts specifically

designed for this unit.

• Improper treatment of generator can damage the unit and shorten its life.

• Always repair this unit as specified in this manual. If you have any questions, contact your dealer or consult a qualified service centre.

• Shut generator off if electrical outpost is missing, unit vibrates excessively or begins to smoke, spark, or emit flames.

• This product contains chemicals known to cause cancer and birth defects or other reproductive harm.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Table of Contents

Safety ............................................................................................................................................................. 2

Safety Symbols ........................................................................................................................................................... 5

Features ......................................................................................................................................................... 9

Parts Identification ...................................................................................................................................................... 9

Control Panel Functions ........................................................................................................................................... 10

ON/OFF Start Switch and Choke ....................................................................................................................... 10

Oil Warning Indicator Light ................................................................................................................................. 10

Engine Overload Indicator Light ......................................................................................................................... 10

AC Pilot Indicator Light ....................................................................................................................................... 10

Engine ECO Control ........................................................................................................................................... 11

Parallel Outlets ................................................................................................................................................... 11

Fuel Cap ............................................................................................................................................................. 11

Fuel Cap Air Vent ............................................................................................................................................... 11

Ground Terminal ................................................................................................................................................ 12

Assembly ..................................................................................................................................................... 13

Connecting the Generator to an Electrical System .................................................................................................. 13

Adding Fuel ............................................................................................................................................................... 13

Adding/Checking Engine Oil ..................................................................................................................................... 14

Operation ..................................................................................................................................................... 15

Grounding the Generator .......................................................................................................................................... 15

Standard Atmospheric Conditions ............................................................................................................................ 15

Starting the Generator .............................................................................................................................................. 15

Stopping the Generator ............................................................................................................................................ 16

Attaching Electronic Devices .................................................................................................................................... 16

AC Parallel Operation ............................................................................................................................................... 17

Avoid Overloading the Generator ............................................................................................................................. 17

Maintenance ................................................................................................................................................ 20

Pre-Operation Steps ................................................................................................................................................. 20

After Each Use .......................................................................................................................................................... 20

Maintenance Schedule ............................................................................................................................................. 20

Checking the Spark Plug .......................................................................................................................................... 21

Carburettor Adjustment ............................................................................................................................................ 21

Changing the Oil ....................................................................................................................................................... 21

Air Filter .................................................................................................................................................................... 22

Checking the Muffler and the Spark Arrester ........................................................................................................... 23

Fuel Tank Filter ......................................................................................................................................................... 24

Fuel Filter .................................................................................................................................................................. 24

Storage ..................................................................................................................................................................... 24

Draining the Fuel ...................................................................................................................................................... 25

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Troubleshooting ......................................................................................................................................... 26

Specifications ............................................................................................................................................. 27

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Features

Parts Identification

Spare parts available

for purchase, scan QR

code below:

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Control Panel Functions

ON/OFF Start Switch and Choke

Start Switch “OFF”

•

When the Start Switch is in the “OFF” position the fuel valve is switched off and

the engine will not run.

Start Switch “CHOKE”

•

When the Start Switch is in the “CHOKE” position, the fuel valve is switched on

and the engine can be started.

Start Switch “ON”

•

When the Start Switch is in the “ON” position, the fuel valve is switched on and the engine can run.

NOTE: The Choke is not required to start a warm engine.

Oil Warning Indicator Light

•

When the oil falls below the minimum level, the oil warning indicator light

comes on and the engine stops automatically. The engine will not start.

NOTE: If the oil warning indicator light does not come on and the engine stalls, turn the Start Switch to “ON”

and pull the recoil starter.

Engine Overload Indicator Light

If the engine overload indicator light comes on, the generator s wattage / amperage capacity has been exceeded

by connected electrical devices or by a power surge. When this occurs, the green AC Pilot Indicator Light will go

off. The engine will continue to run, but the red Engine Overload Indicator Light will stay on and power will no

longer be supplied to connected electronic devices.

How to Correct:

1. Disconnect any electronic devices then stop the engine.

2. Reduce the total wattage of connected electronic devices until it is within the generator’s rated output.

3. Inspect the Air Inlet and Control Panel for any blockage. Remove blockage if found.

4. Restart Engine.

NOTE: The engine overload indicator light may turn on for a few seconds when attaching a load due to a power

surge. This is normal.

AC Pilot Indicator Light

The green AC Pilot Indicator Light comes on when the engine starts and

generates power.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Engine ECO Control

•

When the Engine ECO switch is turned to the “ON” position, the economy control unit automatically

determines the generator’s proper engine speed based on the connected electronic load. This results in

superior fuel economy and reduces noise.

•

When the ECO switch is turned to the “OFF” position, the engine runs at the rated speed of 4,850 r/min.

NOTE: The ECO switch must be turned to the “OFF” position when using electronic devices that require a large

starting current, such as a compressor.

Parallel Outlets

Located just above the Ground Terminal, the generator’s Parallel Outlets enable a user to run two generators

simultaneously. This operation requires special cables. When operating parallel generators, the rated output is

3.0Kva and the rated current is 25A/120V. For cables and instructions, consult an authorised technician or

service centre.

WARNING! Never connect generators that are different models. Only connect this generator to another

SV5000 generator. Only use brands approved parallel operation cable kit to connect the generators.

Fuel Cap

Turn anti-clockwise to remove the fuel cap.

Fuel Cap Air Vent

The fuel cap is equipped with an air vent to stop fuel from flowing to the carburettor.

The Air Vent must be in the “ON” position to allow fuel to flow so that the engine can

run. Turn the Air Vent to the “OFF” position to stop fuel flow.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Ground Terminal

The generator’s ground terminal must always be used to connect the generator to a

driven ground rod. Connect the ground terminal to the driven ground rod with a No 8

AWG (American Wire Gage) copper wire. The wire connects to the terminal between

the lock washer and nut. Tighten the nut securely to ensure good connection.

Grounding the generator protects you from electric shock that results from a build-up

of static electricity or undetected ground faults.

WARNING! Generator must be properly grounded to prevent electrocution.

Only operate generator on a level surface. Always connect the nut and

ground terminal on the frame to an appropriate ground source.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Assembly

WARNING! This generator produces a very high voltage which could result in burn or

electrocution causing serious injury or death.  Never handle the generator, electronic

devices, or any cord while standing in water, while barefoot, or when hands or feet are wet.  Always

keep the generator dry. Never operate generator in rain or under wet conditions.  Use a ground fault

circuit interrupter (GFCI) in a damp or highly conductive area, such as metal decking or steel work. 

Never plug electronic devices into generator having frayed, worn, or bare wires. Never touch bare wires

or make contact with receptacles.  Never permit a child or unqualified person to operate generator.

Keep children a minimum of 10 feet away from the generator at all times.  If using the generator for

backup power, notify your local utility company.  If connecting generator to a building's electrical

system for standby power, you must use a qualified electrician to install a transfer switch. Failure to

isolate the generator from the power utility could result in serious injury or death to electric utility

workers.

Connecting the Generator to an Electrical System

If connecting generator to a building’s electrical system for standby power, you must use a qualified electrician to

install a transfer switch. The power from the generator must be isolated from the circuit breaker or alternative

power source. The connection must comply with all electrical codes and applicable laws.

NEVER DIRECTLY CONNECT THE GENERATOR TO A HOUSHOLD POWER SOURCE!

Adding Fuel

1. Set generator on a clean and level surface in an area that is well ventilated.

2. Remove fuel cap.

3. Insert a funnel into the fuel tank and carefully pour gasoline into the tank until fuel level reaches about 1 ½

inches below the top of the neck. Be careful not to overfill the tank to provide space for fuel expansion.

4. Replace fuel cap and secure tightly.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Adding/Checking Engine Oil

1. Place generator on a level surface.

2. Remove screws and then remove the outer casing cover (You must remove the spark plug cover to push the

side panel off from the inside).

3. Remove the crankcase dipstick.

4. Insert a funnel into the crankcase dipstick hole and carefully add the specified amount of 4-Cycle engine oil

(SAE 10W-30) to empty reservoir until or oil reaches the outer edge of the oil fill hole (crankcase dipstick

hole).

5. Be sure to replace dipstick and securely tighten before attempting to start the engine.

6. To check oil, set generator on a level surface, wipe dipstick clean, then reinsert dipstick without re-threading.

Recommended Oil: SAE 10W-30

Oil Capacity: 0.35L (0.924Gal)

CAUTION! Generator has been shipped without engine oil. You must add oil before first operating this

generator. Always check oil level before each operation.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Operation

Grounding the Generator

To avoid electrocution, this generator must be properly grounded prior to use.

Standard Atmospheric Conditions

•

Ambient Temperature: 77ºF (25ºC)

•

Barometric Pressure: 100kPa

•

Relative Humidity: 30%

Generator output will vary due to changes in temperature, altitude, and humidity. If the temperature, humidity, or

altitude are higher than standard atmospheric conditions, the generator’s output will be reduced. The load

attached to the generator must therefore be reduced.

Starting the Generator

1. Place generator on a level surface. All electrical loads MUST be disconnected from generator.

2. Turn the ECO switch to “OFF”

3. Turn the Air Vent to the “ON” position.

4. Turn the 3 in 1 Start Switch to “CHOKE”

5. Pull recoil handle (starter cord) slowly until resistance is felt, then pull rapidly.

6. Let engine run for several seconds and then gradually, as engine warms up, turn the 3 in 1 Start Switch to

the “ON” position.

WARNING! Pull cord recoils rapidly and pulls arm towards engine faster than you can let go

which could result in injury. To avoid recoil, pull starter cord slowly until resistance is felt, then

pull rapidly.

To start the generator with the ECO switch in the “ON” position:

1. Disconnect all electrical loads from generator.

2. If ambient temperature is below 32ºF (0ºC) allow 3 minutes for the engine to warm up.

3. The ECO is in “ON” position, the unit returns to normal operation after the above warm up time.

4. ECO switch must be turned to the “OFF” position when using electronic devices that require a large starting

current, such as a compressor.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Stopping the Generator

1. Turn the ECO switch to the “OFF” position.

2. Disconnect any electronic device. All loads MUST be disconnected from the generator. Never start or stop

the engine with electrical devices plugged in to the receptacles.

3. Turn the 3 in 1 Start Switch to the “OFF” position.

4. Turn the Air Vent to the “OFF” position.

WARNING! Never start or stop engine with electrical devices plugged in to the receptacles.

Failure to do so could damage the generator and / or connected electrical devices. Always start

the engine and let it stabilize before connecting any electronic devices. Disconnect all electronic devices

before stopping the engine.

Attaching Electronic Devices

1. Before starting generator:

− Make sure the generator is grounded.

− Make sure the attached load is within the generator rated output and the receptacle’s rated current.

− Make sure all electrical cords and receptacles are in good condition.

− Make sure all electronic devices are turned “OFF” before plugging them into the generator.

2. Start engine

3. If the attached load is small, turn the ECO switch to the “ON” position. For a larger load, or if attaching

multiple electronic devices turn the ECO switch to the “OFF” position.

4. Make sure the green AC pilot indicator light is on.

5. When engine has stabilized, plug in and turn on first load. It is strongly recommended to plug in devices with

the largest output first and the smallest output last to help prevent overloading the generator.

6. Allow generator output to stabilise (engine and attached devices run evenly) before plugging in the next load.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

AC Parallel Operation

The SV5000 generator has two models that

are compatible with each other (Standard and

Companion). It is possible to connect two

SV5000 generators to each other, using a

parallel cable kit.

1. Connect PARALLEL OPERATION

CABLES to two SV5000 generators

according to the instructions provided with

the cable kit.

2. Make sure the ECO switch is in the same

position on both generators.

3. All electronic devices should be turned

“OFF” and disconnected from generators

prior to starting generator engines.

4. Start generator engines. Make sure the

green output indicator light comes on for

each generator.

5. When engine has stabilized, plug in

electronic device to AC receptacle and turn on first load.

6. Allow generator output to stabilize (engine and attached devices run evenly) before plugging in the next load.

Maximum Power in Parallel Operation: 4.0kVA

Rated Power in Parallel Operation: 3.0kVA

It is strongly recommended to plug in devices with the largest output first and the smallest output last to help

prevent overloading the generator. Most electronic devices require power beyond its rated wattage to start. This

additional power is referred to as surge watts and usually lasts between 2-3 seconds. When an electronic device

is started, the red overload indicator may come on. This is normal. If the light stays on disconnect all electronic

devices and stop the engine. Refer to Engine Overload Indicator Light.

WARNING! Only connect electronic devices to the generator that are in good working

order and do not exceed the rated power supply of the parallel generators or the desired

receptacle. A faulty appliance or power cord can create an electric shock. Do not use electronic devices

that have a damaged cord or plug. If an appliance begins to operate abnormally, becomes sluggish, or

stalls, turn off and disconnect appliance immediately. The appliance may have a fault, or its rated load

capacity exceeds the power supply of the generator. To avoid damage to generator or electronic device,

do not connect a load to the generator if its electrical rating exceeds that of the receptacle. Never

connect generators that are different models. Only connect this generator to another SV5000 Generator

or SV5000 Companion Generator Only use brands approved parallel operation cable kit to connect

generators. The parallel cable must be removed if operating only one generator. Never disconnect or

remove the parallel operation cable while generator is still running.

Avoid Overloading the Generator

Make sure you can supply enough rated watts for all electronic devices connected to the generator. Rated watts

refer to the power a generator must supply to keep a device running. Surge watts refer to the power a generator

must supply to start an electronic device. This power surge for starting a device usually lasts between 2-3

seconds but this additional output must be taken into account when selecting the electronic devices you plan to

attach to the generator. To prevent overloading the generator take the following steps:

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

1. Add up the total rated wattage of all electronic devices that will be connected to the generator

simultaneously.

2. Estimate surge watts by adding the item(s) with the highest output (it is unnecessary to calculate the surge

output for all devices as they should be connected one at a time).

3. Add the Surge Watts to the total Rated Watts in step 1. Keep total load within generator’s power capacity.

Wattage Reference Guide

(Wattages listed are just approximations. Check electronic device for actual wattage)

Rated Watts Surge Watts

Essentials

75W Light Bulbs 75 each 75 each

18 CU Ft Refrigerator / Freezer 800 2200

Furnace Fan (⅓ HP) 800 2350

Sump Pump (⅓ HP) 1000 2000

Water Pump (⅓ HP) 1000 3000

Heating/Cooling

Dehumidifier 650 800

Table Fan 800 2000

Electric Blanket 400 400

Space Heater 1800 1800

Kitchen

Blender 300 900

Toaster (2 slice) 1000 1600

Coffee Maker 1500 1500

Electric Range (1 element) 1500 1500

Dishwasher 1500 3000

Laundry Room

Iron 1200 1200

Washing Machine 1150 3400

Gas Clothes Dryer 700 2500

Bathroom

Hair Dryer 1250 0

Curling Iron 1500 0

Family Room

X-Box or Play Station 40 0

AM/FM Radio 100 100

VCR 100 100

Colour TV (27”) 500 500

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Rated Watts Surge Watts

Home Office

Fax Machine 65 0

Personal Computer (17” Monitor) 800 0

Laser Printer 950 0

Copy Machine 1600 0

Power Tools

1000W Quartz Halogen Work Light 1000 0

Airless Sprayer (⅓ HP) 600 1200

Reciprocating Saw 960 0

Circular Saw (7 ¼”) 1400 2300

Mitre Saw (10”) 1800 1800

Table/Radial Arm Saw 2000 2000

Electric Drill (½ HP, 5.4 Amps) 600 900

WARNING! Never exceed generator’s wattage/amperage capacity. This could damage the

generator and/or connected electrical devices. Check operating voltage and frequency

requirements of all electrical devices prior to plugging in to the generator.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Maintenance

Regular maintenance will extend the life of this generator and improve its performance. The warranty does not

cover items that result from operator negligence, misuse, or abuse. To receive full value from the warranty,

operator must maintain the generator as instructed in this manual, including proper storage.

WARNING! Before inspecting or servicing this machine, make sure the engine is off and

no parts are moving. Disconnect the spark plug wire and move it away from the spark

plug. If you are unsure of how to perform a maintenance task, have the unit serviced by an authorised

dealer. Only use specified supplier-approved replacements parts.

Pre-Operation Steps

Before starting the engine, perform the following pre-operation steps:

•

Check the level of the engine oil and the fuel tank level. Check for any leakage.

•

Check fuel hose for cracks or damage. Replace if necessary.

•

Make sure the air filter is clean.

•

Remove any debris that has collected on the generator and around the muffler and controls. Use a vacuum

cleaner to pick up loose debris. If dirt is caked on, use a soft bristle brush.

•

Inspect the work area for hazards.

After Each Use

Follow the following procedure after each use:

•

Shut off engine.

•

Store unit in a clean and dry area.

Maintenance Schedule

After First 5 Hours Change Oil

After 8 Hours or Daily

Clean Debris from Generator and Air Filter area

Check Engine Oil Level

6 Months (100-hour use)

Check and Clean Air Filter Element (service more often under wet or dusty conditions).

Change Engine Oil (Service more often under dirty or dusty conditions)

Check Muffler Screen. Replace if necessary.

Service Spark Plug.

Inspect Muffler and Spark Arrester.

12 Months (300-hour use)

Clean Fuel Filter. Replace if necessary.

Check Crankcase Breather Hose for cracks or damage. Replace if necessary.

De-carbonize cylinder head. See an authorised service centre.

Check and adjust Valve Clearance. See an authorised service centre.

Check all Fittings and Fasteners. See an authorised service centre.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Checking the Spark Plug

1. Remove cap. Then remove spark plug cap.

2. Disconnect the spark plug wire from the spark plug.

3. Before removing the spark plug, clean the area around its base to prevent debris from entering the engine.

4. Insert a spark plug socket wrench through the opening on the outside of the cover. Turn the wrench anti-

clockwise.

5. Check for discoloration and clean carbon deposits off the electrode with a wire brush.

6. Check the electrode gap and slowly adjust to 0.7 - 0.8mm (0.028-0.031 in) if necessary.

7. Reinstall spark plug and tighten to Torque 20.0Nm (14.8ft-lb).

8. If spark plug is worn replace only with an equivalent replacement part. Spark plug should be replaced

annually.

9. Reconnect spark plug wire.

10. Replace spark plug cap, then replace cap.

•

Standard Spark Plug: E6RTC/BPR7HS

•

Spark Plug Gap: 0.7 - 0.8mm (0.028-0.031 in)

•

Spark Plug Torque: 20.0Nm (14.8ft-lb)

Carburettor Adjustment

The carburettor is low emission and is equipped with a non-adjustable idle mixture valve. If adjustment is needed

contact an authorised dealer.

Changing the Oil

1. Place generator on a level surface.

2. Run the generator for several minutes until the engine is warm. Turn off generator.

3. Remove screws, then remove outer casing.

4. Remove the crankcase dipstick.

5. Place an oil pan underneath the engine. Tilt generator to collect used oil. Allow oil to drain completely.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

6. Return generator to a level surface.

7. Carefully add 4-Cycle engine oil (SAE 1 0W-30) to empty reservoir until oil reaches the outer edge of the oil

fill hole (Crankcase Dipstick hole).

8. Use a clean rag to wipe up any spilled oil.

9. Replace crankcase dipstick.

10. Reinstall outer casing and tighten screws.

Recommended Engine Oil: SAE 10W-30

Recommended Engine Oil Grade: API Service SE type or higher quality of engine oil.

Engine Oil Quantity: 0.35L (0.924 US gal)

CAUTION! Do not tilt generator when adding oil. This could result in overfilling, which could damage the

engine. Make sure no foreign matter enters the crankcase.

Air Filter

A dirty air filter will reduce the life span of the

engine, make it difficult to start the engine, and

reduce the unit's performance. Replace with new

filter annually.

1. To clean, remove the screws then remove outer

casing.

2. Remove the screws then remove air filter cover.

3. Remove the foam element.

4. Wash the foam element in solvent and let dry.

5. Pour a small amount of oil on the foam element

then squeeze out, but do not wring out, excess

oil. Foam element should be damp, but not dripping.

6. Reinsert the foam element into the air filter case.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

CAUTION! Do not run the generator without reinstalling the foam element or excessive piston

and cylinder wear may result.

Checking the Muffler and the Spark Arrester

1. Inspect muffler for cracks, corrosion, or other damage.

2. Remove screws, then remove shown area of outer casing.

3. Loosen bolt, then remove muffler cap, muffler screen, and spark arrester

4. Check the muffler screen and spark arrester for carbon deposits. Remove carbon deposits with a wire brush.

5. Check the muffler screen and spark arrester for damage. If damaged replace with Our replacement parts

specifically designed for this unit.

6. Install the spark arrester. Align the spark arrester projection with the hole in the muffler pipe.

7. Install the muffler screen and muffler cap.

8. Install the outer casing and tighten the screws.

WARNING! Avoid contacting hot areas of this unit.  Be cautious around the muffler, cylinder,

and other engine parts as they can be extremely hot.  Allow hot components to cool before

touching them.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Fuel Tank Filter

1. To clean, remove the fuel cap and filter.

2. Clean the filter with fuel.

3. Wipe the filter with a clean rag.

4. Re-install the filter.

5. Re-install the fuel cap.

Fuel Filter

1. To clean, remove screws, remove outer casing, and drain fuel.

2. Lift and hold onto the clamp, then remove hose from tank.

3. Take out the fuel filter.

4. Clean the filter with fuel.

5. Wipe the filter with a clean rag and return the filter to the tank.

6. Re-install the hose and clamp.

7. Open the fuel valve. Inspect for leakages.

8. Re-install the outer casing and re-tighten screws.

Storage

To protect your generator from deterioration during long term storage, take the following preventative measures:

Exterior:

•

Remove any debris that has collected on the generator and around the muffler and controls. Use a vacuum

cleaner to pick up loose debris. If dirt is caked on, use a soft bristle brush.

•

Inspect air cooling slots. Remove any debris if obstructed.

•

Store indoors and use a protective cover to protect from dust.

Fuel:

•

For short-term storage, add fuel stabilizer to prevent stale fuel from causing acid and gum deposits in the

fuel system and carburettor.

•

For long-term storage, drain the fuel.

Engine:

•

Remove spark plug. Pour about 1 TBL of SAE 10W-30 engine oil into the spark plug hole, then reinstall

spark plug.

•

With the 3 in 1 switch in the “OFF” position, pull the recoil starter several times to coat cylinder walls with oil.

•

Gently pull the recoil starter until you feel the engine build compression (when you feel resistance). Leave

the engine in this state. This will help prevent rust build up in the cylinder walls.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Draining the Fuel

1. Turn the 3 in 1 switch to the “OFF” position.

2. Remove fuel cap and fuel tank filter.

3. Use a siphon to transfer gasoline from generator into a gasoline approved container.

4. Wipe up any spilled fuel with a clean rag.

5. Start generator engine and let it run until it stops, and all remaining fuel is consumed. Do not connect

electronic devices to generator during this process.

6. Remove outer casing screws, then remove outer casing.

7. Drain fuel from carburettor by loosening the drain screw on the carburettor float chamber.

8. Turn the 3 in 1 switch to “OFF”

9. Tighten the drain screw.

10. Install the outer casing and tighten screws.

11. When the engine has completely cooled down, turn the Fuel Cap Air Vent to the “OFF” position.

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Troubleshooting

Problem Cause Solution

Generator is running but does not

supply power.

1. Green AC Pilot Light Indicator is

off.

2. Poor connection

3. Defective cord set

4. Connected device is faulty

5. Fault in generator

1. Stop engine and restart.

2. Check and repair

3. Check and repair

4. Connect a device that is working

properly

5. Contact an authorised service

centre

Engine runs good without load but

bogs down when loads are

connected.

1. Short circuit in connected device

2. Generator is overloaded

3. Clogged fuel filter

4. Engine speed is too slow

5. Short circuit in generator

1. Disconnect device

2. See “Avoid Overlading the

Generator”

3. Clean or replace fuel filter

4. Contact an authorised service

centre

5. Contact an authorised service

centre

Engine will not start, shuts down

during operation, or starts and runs

rough.

1. 3 in 1 switch set to “OFF”

2. Dirty air filter

3. Clogged fuel filter

4. Out of fuel or stale fuel

5. Spark plug wire disconnected

from spark plug

6. Bad spark plug

7. Water in fuel

8. Over chocking

9. Low oil level

10. Engine has flooded

11. Faulty ignition

1. Turn switch to “CHOKE” then pull

recoil starter.

2. Clean or replace air filter

3. Clean or replace fuel filter

4. Replace fuel

5. Reconnect spark plug wire

6. Clean or replace spark plug

7. Drain fuel tank and replace fuel

8. Turn off choke

9. Add oil level.

10. Wait 5 minutes and re-crank

engine

11. Contact an authorised service

centre

Engine lacks power.

1. Generator is overloaded

2. Clogged fuel filter

3. Dirty air filter

4. Engine needs servicing

1. See “Avoid Overlading the

Generator”

2. Clean or replace fuel filter

3. Replace air filter

4. Contact an authorised service

centre

Engine “hunts” or falters. 1. Choke was removed too soon

2. Clogged fuel filter

3. Carburettor is running too rich or

too lean

1. Move to choke until engine runs

evenly

2. Clean or replace fuel filter

3. Contact an authorised service

centre

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

SV5000 Inverter Generator

Specifications

Max Output 2600W (Starting watts)

Continuous Rated Output 2200W / 2.2kW

Note: Continuous Rated Output is what power this generator consistently and reliably provides. We strongly

recommend that you consider this figure when determining whether this model suits your requirements.

AC Outlet 2x 240v

DC Outlet 2x USB

Fuel Tank Capacity 4.5 Litres

Engine Type 4-stroke Petrol Engine

Fuel Type Regular unleaded (Min 95 RON)

Engine Oil Type 10W-30 non-synthetic engine oil (not included with purchase)

Runtime 3 hours (6 hours @ 50% load)

Noise Level 61dB

Parallel Outlet 2

Ignition System CDI

Warranty 3 Years

See full details of the 3 Month Satisfaction Guarantee

GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER GENPOWER

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business

or employee, or financially affect the user, business or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement or service by a technician

may cause financial loss, loss of employee time or an

inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

ideas, diagrams or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

GENPOWER GENPINGPRA5M0-X2 2 x 2200W Portable Power Generator

Product's Documents

Product manual

Specifications

GENPOWER GENPINGPRA5M0-X2 Questions and Answers