Loading ...
Loading ...
Loading ...
ENGLISH
6
Bottle Runs Out During Mixing (Fig. F, J)
If a bottle runs out of liquid while the cocktail maker is
mixing a drink:
• The cocktail mixer will enter pause mode for 2 minutes to
allow you to replace the empty bottle. Refer to the PAUSE
MODE section for more information.
• Do not turn the power switch14 off. Turning it off will
reset the mixing process and the cartridge will no longer
be able to beused.
NOTE: The unit will not flush the lines while the capsule
holder lid 22 is lifted.
To replace the empty bottle:
1. Remove the bottle as described in the REMOVING
BOTTLESsection.
2. Install the a new bottle as described in the INSTALLING
BOTTLESsection.
3. Press the mix button26 to resume mixing the drink
from where it leftoff.
Making a Drink (Fig.F–J)
WARNING: To ensure liquor is not dispensed while
making a mocktail, lift straw locks8 for the alcohol
bottles and keep the water bottle straw lockdown.
1. Turn the cocktail maker on as described in the ON/
OFFsection.
2. Place a glass or shaker on the glass shelf17 or drip tray3
depending on its height as described in the CHOOSE A
GLASS TRAYsection.
3. Insert the desired capsule20 into the capsule holder21
as described in the INSERTING CAPSULEsection.
4. Turn the strength selector dial25 to set the alcohol
content as described in the SELECT ALCOHOL
STRENGTHsection.
5. Bottles used for the drink recipe will light up. Ensure
bottles are installed in all locationsilluminated.
6. Push the mix button26 to begin making adrink.
7. The bottle LED will light under the bottle whose liquid is
beingdispensed.
8. It is complete when all the LEDs becomesolid.
9. Remove the capsule before removing the glass. The
capsule may drip when it is being removed and if left in
theholder.
NOTE: While making a drink, if the power button is turned off, the
appliance is unplugged, or after one minute in pause mode, the
mixing process will be reset, ending the mixing of the current drink.
If this happens, a small amount of alcohol may remain in the internal
lines. To ensure the next drink is not mixed with this remaining
alcohol, clean the lines as described in the CLEANING MODE section
before mixing another drink. To resume making the drink while in
pause mode, refer to the PAUSE MODEsection.
NOTE: If the cocktail maker continues to dispense to the
point of overflow, turn the appliance off, lift the straw lock, or
lift the capsule holder lid22.
Select Alcohol Strength (Fig.J)
To select the amount of alcohol to be dispensed into the
drink, turn the strength selector dial25.
• Left: less alcohol
• Right: more alcohol
The strength LEDs15 will turn on and off as you turn the
selector, indicating the strength of thedrink.
• ‑ mocktail (no alcohol)
Inserting a Capsule (Fig.H, I)
WARNING: Cut Hazard. Do not probe capsule holder
area withfingers.
WARNING: Pinch point. Keep away from capsule
holder when closing capsule holder lid.
WARNING: Use only Bartesian capsule. Use with any
other capsule may result in damage to theappliance.
IMPORTANT: Do not open capsule20.
IMPORTANT: Once the capsule is punctured, it may drip
liquid. To avoid this, place a capsule in the capsule holder21
just before mixing adrink.
1. Before inserting a capsule, place a glass or shaker on the
glass shelf17 or drip tray3 as described in the CHOOSE A
GLASS TRAY section
2. Select the capsule you wish touse.
3. To open the capsule holder, lift the capsule holder lid22
until it clicks intoplace.
4. Ensure the bar code 32 is clean from liquid and
debris. Wipe your thumb across the bar code before
inserting capsule into capsule holder.
5. Place the capsule in the capsule cup23 located in the
holder. Ensure the capsule tab24 faces to the left. The
cocktail maker will not operate if the capsule is inserted
any otherway.
6. Ensure the capsule sits fully in the capsulecup.
NOTE: The scanner inside the capsule holder scans the code
on top of the capsule. This allows the cocktail maker to pull
from the correct bottles so it dispenses the correctdrink.
7. Push the capsule holder lid down to close the capsule holder
until it clicks. Ensure the lid is fully closed beforeoperating.
NOTE: If the capsule code is successfully read, the bottle
LEDs16 will light under the bottles that are being used.
Ensure each bottle is in its correctplace.
NOTE: If lights do not turn on, lift the capsule holder lid and
use a clean, dry towel to wipe the barcode scanner31 and the
capsule barcode32 as shown in Fig. I. Then, repeat step6.
Tall glass:
1. Push the glass shelf up so it hides away in thetower.
2. Ensure the drip tray cover4 is inplace.
3. Place a tall glass on the drip traycover.
Shaker:
The shaker LED19 will light when a drink needs to be
shaken. In this case, use a shaker instead of a tallglass.
1. Push the glass shelf up so it hides away in thetower.
2. Ensure the drip tray cover is inplace.
3. Place a shaker on the drip traycover.
• ‑ light alcohol content
• ‑ regular alcohol content
• ‑ strong alcohol content
Loading ...
Loading ...
Loading ...