Original instructions.
© 2023 Snow Joe, LLC. All rights reserved.
1
EN
A Division of Snow Joe, LLC
OPERATOR’S MANUAL
R
Model 24V-HCSEC-LT
Form No. SJ-24V-HCSEC-LT-880E-M
CORDLESS PRUNING SAW
24V MAX* | 2.5 Ah | 5-INCH | BONUS CUTTING CHAIN
*Initial no-load voltage, when fully charged, peaks at 24V;
nominal voltage under typical load is 21.6V.
SAVE THESE INSTRUCTIONS
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/
or serious injury. Save all warnings and instructions for future
reference.
mDANGER! This indicates a hazardous situation, which,
if not followed, will result in serious injury or death.
mWARNING! This indicates a hazardous situation, which, if
not avoided, could result in serious injury or death.
mCAUTION! This indicates a hazardous situation, which, if
not avoided, could result in minor or moderate injury.
Intended Use
This cordless prunning saw was designed and manufactured for
trimming and pruning tree limbs and branches and for cutting
smaller logs up to the recommended 4.5 in.
(11.4 cm), not to exceed a max. cut of 5.5 in. (14 cm) in
diameter depending on type of wood. All of the wooden objects
intended to be cut with this pruning saw should be no thicker
than the guide bar's maximum cutting capabilities.
Any other use differing from the above mentioned applications
poses a serious hazard to the user and may damage both the
tool and your personal property. Improper use of the machine
will invalidate the warranty and relieve the manufacturer from all
liabilities. The user will consequently be liable for all and any
damage or injury to himself/herself or others.
General Power Tool Safety
Warnings
mWARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury. Save all warnings and
instructions for future reference.
Work Area Safety
1. Keep work area clean and well lit – Cluttered or dark
areas invite accidents.
2. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust – Power tools create sparks which may ignite the dust
or fumes.
3. Keep children and bystanders away while operating a
power tool – Distractions can cause you to lose control.
Electric Safety
1. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools – Unmodified plugs and
matching outlets will reduce risk of electric shock.
2. Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators –
There is an increased risk of electric shock if your body is
earthed or grounded.
3. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts – Damaged
or entangled cords increase the risk of electric shock
4. When operating a power tool outdoors, use an extension
cord suitable for outdoor use – Use of a cord suitable for
outdoor use reduces the risk of electric shock.
5. If operating a power tool in a damp location is
unavoidable, use a RESIDUAL CURRENT DEVICE (RCD)
protected supply – Use of an RCD reduces the risk of
electric shock
Personal Safety
1. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence
of drugs, alcohol or medication – A moment of inattention
while operating power tools may result in serious personal
injury.
2. Use personal protective equipment. Always wear
eye protection – Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will
reduce personal injuries.
Loading ...
Loading ...
Loading ...
