Loading ...
Loading ...
Loading ...
To remove the base grille:
1. Open the refrigerator and freezer doors 90°.
2. Using a Phillips screwdriver, remove the screws attaching the
base grille to the refrigerator cabinet.
3. Pull the base grille toward you.
NOTE: Do not remove the Tech Sheet that is fastened behind
the base grille.
1. Screws
To replace the base grille:
1. Open the refrigerator and freezer doors to 90 °.
2. Position the base grille so that the holes are aligned and
replace the screws.
Your refrigerator has a front and rear roller at the base of the
product on each side. All four rollers can be adjusted from the
front of the product. If your refrigerator seems unsteady or you
want the doors to close easier, adjust the refrigerator's tilt using
the instructions below:
1. Check the installation location to be sure that you have the
proper clearance for the refrigerator. See the "Location
Requirements" section.
2. Plug into a grounded 3 prong outlet.
3. Move the refrigerator into its final position.
4. Open the refrigerator and freezer doors to locate the leveling
bolts at the left and right of the refrigerator base. If your
refrigerator has a base grille, remove it. See "Base Grille"
earlier in this section.
G W ......................... 1
1. Rear leveling bolt
2. Front leveling bolt
NOTE: The top bolt will adjust the rear of the refrigerator, and
the bottom bolt will adjust the front of the refrigerator.
5. Use a 1/2in. (12.70 ram) socket wrench to adjust the leveling
bolts. Turn the leveling bolt to the right to raise that side of the
refrigerator or turn the leveling bolt to the left to lower that
side. It may take several turns of the leveling bolts to adjust
the tilt of the refrigerator.
NOTE: Be careful not to unscrew the leveling bolts too much
when lowering the refrigerator. The bolt head will start to
come away from the refrigerator when in the lowest position.
If the screw does come out of the rear roller bracket, the
compartment access cover on the back of the refrigerator will
have to be removed to reinstall the bolt.
6. Adjust the front leveling bolt to bring the refrigerator top
parallel with the cabinet above the refrigerator. For standard
cabinets, leave approximately 1/8in. (3.18 mm) gap between
the top hinges and the cabinet. For full-overlay cabinets,
leave I/4 in. (6.35 mm) gap for leveling. If you do not have a
cabinet above the refrigerator, simply adjust the refrigerator to
make it level.
1. For standard cabinets, leave _ in. (3.18 ram) minimum clearance
for leveling the refrigerato_ For full-overlay cabinets, leave ¼ in.
(6.35 mm) minimum clearance for leveling and door clearance.
2. Front of the refrigerato_
71
8.
Adjust the rear leveling bolt to bring the refrigerator level with
the side cabinets or cabinet end panels.
If you want, you may now use the four leveling bolts to raise
the refrigerator to close the gap between the refrigerator top
hinge and the cabinet opening. Check that all four rollers still
touch the floor and that the cabinet doors above the
refrigerator open all the way.
9. Replace the base grille.
Read all directions before you begin.
IMPORTANT: If you turn the refrigerator on before the water line
is connected, turn the ice maker OFE
Connecting to Water Une
11
2.
31
Unplug refrigerator or disconnect power.
Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
Find a _/2in. (12.70 ram) to 1% in. (3.18 cm) vertical COLD
water pipe near the refrigerator.
NOTE: Horizontal pipe will work, but the following procedure
must be followed: Drill on the top side of the pipe, not the
bottom. This will help keep water away from the drill. This
also keeps normal sediment from collecting in the valve.
4. Route V4in. (6.35 mm) copper tubing from the water pipe to
the lower rear corner of the refrigerator location. Be sure both
ends of copper tubing are cut square.
5. Using a grounded drill, drill a 1/4in. (6.35 mm) hole in the cold
water pipe you have selected.
1. Cold water pipe 5. Compression sleeve
2. Pipe clamp & Shutoff valve
3. Copper tubing 7. Packing nut
4. Compression nut
6
Loading ...
Loading ...
Loading ...