Faber CLPL30SSV2 30 Inch Pyramid Wall Hood

Installation Instructions - Use and Care Information - Page 43

For CLPL30SSV2. Series: Classica Plus
Also, The document are for others Faber models: CLPL36SSV2

PDF File Manual, 72 pages, Read Online | Download pdf file

CLPL30SSV2 photo
Loading ...
Loading ...
Loading ...
43
EN
7
7
INSTALLATION
Fitting the Hood canopy
BEFORE FITTING THE HOOD TO THE WALL UNIT, PROCEED AS FOLLOWS:
Disconnect the wires to the Commands at the connectors.
Disconnect the wires to the Light at the con-
nectors.
The Hood can be installed directly on the
underside of
the wall unit (Minimum 650 mm
from the Cooker Hob).
Create an opening in the bottom of the wall unit,
as shown.
Insert the hood until the side supports snap into
place.
Fasten using the 10 screws 12a provided.
Lock in position by tightening the screws Vf from
underneath the hood.
Open the suction panel by turning the specific knob.
Disconnect the panel from the hood canopy by sliding the
fixing pin lever.
Remove grease filters.
Screw the Frame into place
using the 6 scr
ews 12f, re-
connect the wires to the
Commands and Light, re-
place the metal grease filter
and the Panel.
260
13
495 - 675
ENTRETIEN DES FILTRES
Retirez le ltre en poussant le levier vers l'ar-
rière de l'appareil tout en tirant vers le bas.
Lavez le ltre sans le plier. Laissez-le sécher
complètement avant de le remettre en place.
Si la surface du ltre change de couleur avec le
temps, l'efcacité n'en sera pas affectée.
Pour remplacer le ltre, poussez-le vers le haut
en position tout en maintenant le levier en
arrière, puis relâchez le levier pour le verrouiller
en place.
1
2
3
EN
7
7
INSTALLATION
Fitting the Hood canopy
BEFORE FITTING THE HOOD TO THE WALL UNIT, PROCEED AS FOLLOWS:
Disconnect the wires to the Commands at the connectors.
Disconnect the wires to the Light at the con-
nectors.
The Hood can be installed directly on the
underside of
the wall unit (Minimum 650 mm
from the Cooker Hob).
Create an opening in the bottom of the wall unit,
as shown.
Insert the hood until the side supports snap into
place.
Fasten using the 10 screws 12a provided.
Lock in position by tightening the screws Vf from
underneath the hood.
Open the suction panel by turning the specific knob.
Disconnect the panel from the hood canopy by sliding the
fixing pin lever.
Remove grease filters.
Screw the Frame into place
using the 6 scr
ews 12f, re-
connect the wires to the
Commands and Light, re-
place the metal grease filter
and the Panel.
260
13
495 - 675
NETTOYAGE DES FILTRES À GRAISSE MÉTALLIQUES
Les ltres à graisse métalliques peuvent être nettoyés dans une solution
détergente chaude ou lavés au lave-vaisselle.
Ils doivent être nettoyés tous les 2mois d'utilisation, ou plus fréquemment
si l'utilisation est particulièrement intensive.
NOTES:
• Le nettoyage dans un lave-vaisselle peut ternir la nition des ltres à
graisse en métal.
Assurez-vous que les ltres sont complètement secs avant de les réinstal-
ler dans la hotte.
NETTOYAGE DES SURFACES EXTÉRIEURES
Veuillez noter que les abrasifs et les agents de récurage peuvent rayer les
nitions de la hotte et ne doivent pas être utilisés pour nettoyer les surfaces
de nition.
Instructions de nettoyage de la nition en acier inoxydable:
Nettoyez les surfaces extérieures avec un nettoyant pour acier inoxydable
disponible dans le commerce.
Loading ...
Loading ...
Loading ...