Loading ...
Loading ...
RULESFORSAFEOPERATION(Continued)
10. WEAR PROPER APPAREL. No loose clothing 24.
or jewelry to get caught in moving parts. Rubber 25.
gloves and non-skid footwear are recommended
when working outdoors. Also, wear protective
hair covering to contain long hair and keep it 26.
from being drawn into air vents.
1t. ALWAYS WEAR SAFETY GLASSES. Everyday
eyeglasses have only impact-resistant lenses;
they are NOT safety glasses. 27.
12. PROTECT YOUR LUNGS. Wear a face or dust
mask it operation is dusty. 28.
13. PROTECT YOUR HEARING. Wear hearing pro-
tection during extended periods of operation.
14. DON'T ABUSE CORD. Never carry tool by cord
or yank it to disconnect from receptacle, Keep
cord from heat, oil and sharp edges. 29,
15. SECURE WORK. Use clamps or a vise to hold
work. Both hands are needed to operate the
tool. 30.
16. DON'T OVERREACH. Keep proper footing and
balance at all times. Do not use on a ladder or
unstable support.
17. MAINTAIN TOOLS WITH CARE. Keep tools
sharp at all times, and clean for best and safest
performance. Follow instructions for lubricating
and changing accessories.
18. DISCONNECT TOOLS. When not in use, before
servicing, or when changing sanding belts, at-
tachments, blades, bits, cutters, etc., all tools
should be disconnected from power supply. 31.
19. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to see that
keys and adjusting wrenches are removed from 32,
too[ before turning it on.
20. AVOID ACCIDENTAL STARTING, Don't carry 33.
plugged-in tools with finger on switch. Be sure
switch is off when plugging in.
21. MAKE SURE YOUR EXTENSION CORD IS IN 34.
GOOD CONDITION. When using an extension
cord, be sure to use one heavy enough to carry
the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in
loss of power and overheating, A wire gage size 35.
(A.W.G.) of at least 14 is recommended for an
extension cord 100 feet or less in length. A cord 36.
exceeding 100 feet is not recommended. If in
doubt, use the next heavier gage. The smaller
the gage number, the heavier the cord.
22. OUTDOOR USE EXTENSION CORDS. When
tool is used outdoors, use only extension cords
suitable for use outdoors. Outdoor approved
cords are marked with the suffix W-A, for ex-
ample - SJTW-A or SJOW-A. 37.
23. NEVER USE THIS OR ANY POWER SANDER
FOR WET SANDING. Failure to comply can re-
sult in electrical shock causing serious injury or
worse.
Page 3
KEEP HANDS AWAY FROM SANDING AREA.
NEVER USE IN AN EXPLOSIVE ATMO-
SPHERE. Normal sparking of the motor could
ignite fumes,
INSPECT TOOL CORDS PERIODICALLY and
if damaged, have repaired at your nearest Sears
Repair Center, Stay constantly aware of cord
location,
INSPECT EXTENSION CORDS PERIODICALLY
and replace if damaged,
KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a clean
cloth when cleaning, Never use brake fluids, gaso-
line, petroleum-basod products or any strong sol-
vents to clean your tool.
STAY ALERT. Watch what you are doing and
use common sense. Do not operate tool when
you are tired. Co not rush.
CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced
by an authorized service center unless indicated
elsewhere in this instruction manual.
DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
Inspect for and remove all nails from lumber
before sanding.
DRUGS, ALCOHOL, MEDICATION. Do not op-
erate tool while under the influence of drugs,
alcohol, or any medication.
DO NOT USE THIS SANDER FOR OVERHEAD
SANDING, Overhead sanding could result in
dropping sander or loss of control. These situa-
tions could result in an accident resulting in pos-
sible sedous injury.
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS.
POLARIZED PLUGS. TO reduce the dsk of elec-
tric shock, this tool has a potadzed plug (one
blade is wider than the other). This plug will fit in
a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug, if it still
does not fit, contact a qualified electrician to
install the proper outlet, DO not change the plug
in any way,
SAVE THESE INSTRUCTIONS. Refer to them
frequently and use to Instruct others who may
use this tool. If you loan someone this tool, loan
them these instructions also.
Loading ...
Loading ...
Loading ...