Loading ...
Loading ...
Loading ...
Remote Control
Timer Pad
Timer ON: Can be set under off state of unit. If
timer ON reaches, the system
will run under Energy Save mode. The se tting
range is 0.5~24hr.
Filter check Pad
Air Conditioner Use
16
NOTE: When user cleaned the filter, press Filter
check button to clear the operation time. Mean-
while, the warning indicator will turn off.
Timer OFF: Can be set under on state of unit. If
timer OFF reaches, the unit will
turn off. The timer can be set in 0.5 hour increment
below 10 hours and in 1 hour
increment for 10 hours or above.
After fan rotates for 250h totally, lamp of cleaning
filter is on to remind customer clean it.
dehumidification and the corresponding indicator is
on; under dry mode, the fan speed cannot be ad-
justed.
2
7
4
3
8
6
Remote Control
5
1
1
ON/OFF :
2
MODE :
3
4
+
:
Press this button to increase set temperature. Holding
it down above 2 seconds rapidly increases set temper-
ature.
In AUTO mode, set temperature is not adjustable.
AUTO
SAVE
COOL
FAN DRY
-
:
Press this button to decrease set temperature. Holding
.
it down above 2 seconds rapidly decreases set temper-
ature.In AUTO mode, set temperature is not adjustable.
model.
6
I FEEL:
I feel function will be action if pressing this button.
If controller receives I FEEL order, it will work under
ambient temperature value which sending by remote
controller, and remote controller will send ambient
temperature value to controller every 10min. After
11min, if controller does not receive ambient temperature
value which sending by remote controller, it will run with
AC ambient temperature; if I FEEL is not set, ambient
temperature will adopt sampling value of AC temperature
sensor. If power off happens, this function will not be
memorized.
Press " + " and " - " buttons simultaneously
to lock or unlock
the keypad. If the remote controller is locked,
is displayed
In this case,pressing any button,
blinks three times.
9
Combination of "+" and "-" buttons: About lock
12
About Energy saving
Under energy saving mode, lamp of energy saving mode
is on, and the temperature setting range is 61~86℉(16~
30℃). The buzzer will give out a beep if remote control
turbo speed by remote controller, and runs with high
speed.
,then back to A
uto.
Auto
5
FAN
:
to
This button is used for setting Fan Speed in the
sequence that goes from AUTO,
,
,
Speed 1 Speed 2
Speed 3
Speed 4
NOTE: There are 3 speeds for the Fan Speed of this
Press this button to turn on the unit. Press this button
again to turn off the unit.
7
SLEEP:
Each time you press the button, a mode is selected
in a sequence that goes from AUTO, COOL, SAVE
FAN, and DRY , as the following:
11
Press this button to go into the SLEEP operation mode. Pre-
ss it again to cancel this function. This function is available in
COOL, or DRY mode to maintain the most comfortable temp-
erature for you.
8
TIMER:
Under switch-on or switch-off state, you may hold "+"
and "FAN"
buttons simultaneously for
3 seconds to set
the lamp on or off and send the code. After being energi-
zed the lamp is
defaulted on.
Press this button to initiate auto-on/auto-off timer. To
cancel auto-timer program, press this button twice.
10
Combination of "MODE " and "-" buttons:
About switch between fahrenheit and cenrigrade
At unit OFF, press“ MODE ” and “ - ” buttons simultan-
eously to switch between ℃ and
About Lamp
Temperature display switchover function
ŀĿ
Press " " button and " " button simultaneously for
3 seconds can switch between °C and °F
Function introduction for combination buttons
Loading ...
Loading ...
Loading ...