Loading ...
Loading ...
Loading ...
About storage drawer and cover removal, ge.com
Not aft features are on aft models.
Humidity Control
HIGH LOW
Adjustable Humidity Drawer (onsomemodels)
Slide the control all die way to the Slide the control all die way to the LOW
HIGHsetting to provide high humidity setting to provide lower humidity levels
recommended for most vegetables, recommended for most fl_uits.
Drawer and Cover Removal
Drawers can be removed easily by grasping the sides and lifting up slighdy while pulling
drawers past tile stop location.
i
Full-Width Drawer with
Plastic Cover
Toremovethecover,lift it off its supports,
pull it forward, tilt it and take it out.
!iii /iii
7¸ • :i;i •_ ....
Twin Drawer Shelf
Toremove:
[-'7]Remove tile dxmvers.
F_-]Reach in, push the flont of glass cover
up, and at the same time, pull it forward
_tsfar as it will come.
Tilt it and take it out. Avoid cleaning the cold
glass covet"with hot water becmlse the exu'eme
temperature difference mW cause it m break.
_] Remove tile drawer flmne. (Always
remove tile ,glasscover before you rake
out the drawer flame.)
iJfi the fi'mne off the supports at each side
aud back, pull it forward, flit it aud take it out.
Toreplace:
[-_ Lower tile frame until it rests (m tile
supports at each side and back.
F_--]Replace tile glass covei, pushing its rear
edge firmly into the rear flvmm channel
and gendy lowedng tile flont into place.
[j] Replace tile (hmve_s.
About the automatic icemaker.
A newly-installed refrigerator may take 12to 24 hours to begin making ice.
There are 2 types of icemakers:
PowerSwitih ]cemaier
GreenPowerLight FeelerArm
Power switch model
FeelerArmin
theSTOP
FeelerArmin (up) position
theON (down)
position
Feelerarmmodel
Automatic Icemaker (onsomemodels)
The icemaker will produce approximately
100-130 cubes in a 24-hour period,
depending on the fl'eezer compai'unent
temperature, room temperature, number of
door openings mid other rise conditions.
If the refl'igeramr is operamd before the water
connection is made to the icemaket; move the
feeler m'm to the STOP(.p)position.
When the refligeramr has been connecmd
m the wamr supply, move the feeler am1 m
the ON (down) position.
The icemaker willfill with water when it cools
to 15°E A newly-installed refi'igerator mW rake
12 m 24 hours to begin making ice cubes.
Once the icemaker starts m make ice,
it mW take up m 48 hours m fill the bin,
depending on the mmperamre setdngs
and number of door openings.
You will hear a buzzing sound each dine
the icemaker fills with WamL
Throw away tile fi[st few batches of ice
to allow the water line to cleaL
Be sure nothing interferes with tile sweep
of tile feeler arm.
When die bin fills to die level of die feeler
arm, die icemaker will stop producing ice.
It is normal for severed cubes m be joined
mgetheL
If ice is not used flequendy, old ice cubes
will become cloudy, tasm stale, shrink or
fuse mgetbeL
On power switch models, the g_een power
light will blink if ice cubes get stuck in the
icemakeL To correct this, set the power
switch m 0 (off) and remove the cubes. Set
the power switch m I (on) m resm_* the
icemakeL Af_er the icemaker h_ts been
turned on again, there will be a del W of
about 45 minums before tile icemaker
resumes ope_v_fion.
NOTE:In homeswith lower-than-averagewater
pressure,youmayhear the icemakercycle multiple
times when makingonebatch of ice.
IcemakerAccessoryKit
If your refi'igerator did not ah'eady come
equipped with an maomafic icemaker, an
icemaker accessoWkit is available at extra cost.
Check tlle back of tlle refligerator for
tile specific icemaker kit needed for 7
your model.
Loading ...
Loading ...
Loading ...