Loading ...
Loading ...
Loading ...
If the water does not fl ow due to a water service interruption
■
Replacing the batteries
1
Unplug the power plug.
<Power>
2
Remove the remote control from the
hanger.
(Page 14)
3
Open the battery cover and replace two
AA batteries.
(Page 14)
•
The low battery warning mark goes off .
4
Mount the remote control in the hanger.
5
Insert the power plug.
•
The "Power" LED lights up.
If you cannot operate with the remote control
Attention!
•
"ON" and "OFF" settings of the functions such as the energy saver function may be canceled when the batteries
are replaced. Set them again.
■
If the low battery warning mark "
" on the back
of the remote control is fl ashing, please replace the
batteries.
It is the time to replace
the batteries.
Freeze Damage Prevention
Water supply hose
Horizontally
1
Use a bucket to fl ush water.
2
If the water level is low after
fl ushing, add more water.
• Prevents odors.
• When the water supply is restored, be sure to perform
a fl ush.
(To prevent waste from remaining in the drain pipe.)
Attention!
Newspaper,
dust cloth, etc.
Large bucket
Pour strongly,
aiming at the center
of the bowl unit.
When the ambient temperature is likely to drop to 32 °F (0 °C) or lower, take measures to prevent freezing.
• When the ambient temperature is likely to drop to 32 °F (0 °C) or lower, do not use the energy saver feature.
(May damage the product.)
• Warm the bathroom or take measures against freezing so that the ambient temperature does not drop below 32 °F (0 °C).
Attention!
How to freeze damage prevention
1
Close the shutoff valve.
(Page 36)
• The water supply stops.
Do not remove the water fi lter drain valve
while the shutoff valve is open.
(Otherwise, water may leak out)
CAUTION
■
To use the product again
• The water needs to be resupplied. (Page 40)
7
(2) [Applicable to SW3084 only]
• Drain the water from the water supply hose.
• Insert the water fi lter drain valve and use a
fl at-head screwdriver to tighten it securely.
(3) When water draining is completed, reinstall
the water fi lter drain valve and cover.
6
Insert the power plug.
• The "Power" LED lights up.
Set the water and toilet seat
temperature to "High".
(Page 20)
• To maintain the temperature, close the toilet seat
and toilet lid after fi nishing work.
2
Drain the water from the toilet
tank.
• Manipulate the lever/button/etc. until the
water stops.
4
Unplug the power plug.
5
Drain the pipe.
(1)
Remove the cover and water fi lter drain valve.
• Loosen the water fi lter drain valve with a
fl at-head screwdriver and then pull it.
Flat-head screwdriver
Cover
Water fi lter drain
valve
3
What to Do?
If the water does not fl ow due to a water service interruption
If you cannot operate with the remote control
(1) Press "Wand cleaning" button.
(2)
Press "Stopping" button on the front
side of the remote control.
•
The wand retracts.
Extend the wand.
(Release the pressure from the water supply pipe.)
To operate from the back of remote control
To operate from the front of remote control
•
Recommended if the remote control is secured to
prevent theft.
(1) Press "Stopping" button until all LEDs
on the remote control start fl ashing. (about
10 seconds)
(2)
Press "Front cleansing" button about 3
seconds or longer.
(3)
Press "Stopping" button on the front
side of the remote control.
•
The wand retracts.
38 39
Reference
Loading ...
Loading ...
Loading ...