Loading ...
Loading ...
Loading ...
Grill Lighting Instructions
1. Before each use, check all hoses for cracks, nicks, cuts,
burns or abrasions. If a hose is damaged in any way, do
not use your grill before replacing the hose with an
authorized part from the Parts List. Also make sure all
gas supply connections are securely tightened.
2. Familiarize yourself with the safety and Use and Care
instructions in this manual. Do not smoke while lighting
grill or checking gas supply connections.
3. Be sure the LP Gas tank is filled.
4. Open the Grill Lid.
5. Check that the end of each Burner Tube is properly
located over each Valve Orifice.
Failure to replace a faulty hose, secure gas supply
connections or to open the Lid before proceeding
to the Lighting Procedures could result in a fire
or explosion that could cause serious bodily injury,
death, or property damage.
6. Set Control Knobs to OFF and open the LP Gas
tank valve SLOWLY 1/4 of a turn.
|
OFF
Open LP Gas_
7. Push and turn the Control Knob to HIGH.
l
HIGH
t
OFF ((3 )
8. immediately press the Electric ignitor for 3-4
seconds to light the Burner.
PRESS
9. If ignition does not occur in 5 seconds, turn gas off at
source and turn Control Knobs OFF. Wait at least 5
minutes for gas to clear, then retry. If your grill still fails
to light turn the burner Control Knob(s) and gas source
OFF and conduct a leak test of ALL gas connections
and gas sources as explained in the Use and Care
section of this manual. If no leaks are detected, wait 5
minutes for any gas to clear and repeat the lighting
procedure.
Back Burner Lighting Instructions
1. Follow steps 1 through 6 of the Grill Lighting
Instructions.
2. Push and turn the Control Knob to ON. Immediately
press the Electric ignitor for 10 seconds to light the
Burner.
I
ON
PRESS
3. If ignition does not occur in 5 seconds, turn gas off
at source and turn Control Knobs OFF. Wait at least
5 minutes for gas to clear, then retry. If your grill still
fails to light turn the Control Knob and gas source
OFF and conduct a leak test as explained in the
Use and Care section of this manual. If no leaks
are detected, wait 5 minutes for any gas to clear
and repeat the lighting procedure.
4. After Burner is lit, turn the tank valve SLOWLY one
more 1/4 of a turn for 1/2 of one complete turn.
IMPORTANT: Do not use the Back Burner and Main
Burners at the same time. Backburner is for Rotis-
serie Cooking only.
Side Burner Lighting Instructions
1. Follow steps 1 through 5 of the Grill Lighting
instructions.
2. Open Side Burner Lid.
3. Set Control Knobs to OFF and open the LP Gas
tank valve SLOWLY 1/4 of a turn.
4. Push and turn the Control Knob to HIGH. The built-in
spark ignitor will light the Burner automatically.
5. You may have to push and turn the Control Knob up
to 3 or 4 times to light.
6. If ignition does not occur, turn gas off at source and
turn Control Knobs OFF. Wait at least 5 minutes for
gas to clear, then retry. If your grill still fails to light turn
the burner Control Knob and gas source OFF and
conduct a leak test as explained in the Use and Care
section of this manual. If no leaks are detected, wait
5 minutes for any gas to clear and repeat the lighting
procedure.
Manually Lighting Your Grill By Paper Match
To light your gas grill by match, insert a match into the
Lighting Stick and follow steps 1 through 6 of the Grill
Lighting instructions. Then, light the match and place
Lighting Stick through the Lighting Hole on the left side
of the grill as shown below. Turn the nearest Control
Knob to the HIGH setting to release gas. The Burner
should light immediately.
10. After one Burner is lit, turn the tank valve SLOWLY one
more 1/4 of a turn for 1/2 of one complete turn.
11. Repeat steps to light each burner individually. Turn
other burners to HIGH to light as you move towards the
fuel source.
Lighting Hole
Lighting St
Match
18
Loading ...
Loading ...
Loading ...