Dewalt DCW682B Instructional Manual

Loading ...

ENGLISH

NOTE: A biscuit joiner can be placed against the workpiece

before starting. It should be allowed to come up to speed

before plunging. Allow the tool to stop rotating before

putting itdown.

1. To turn the tool on, push the lock‑off lever

2

toward the

back of the tool, then depress the paddle switch

1

. The

tool will run while the switch isdepressed.

2. Turn the tool off by releasing the paddleswitch.

No-Volt

The No‑volt function stops the biscuit joiner from restarting

without the switch being cycled if there is a break in the

powersupply.

Blade Replacement (Fig. A, G)



WARNING: To reduce the risk of injury, turn unit

off and disconnect it from power source before

installing and removing accessories, before adjusting

or when making repairs. An accidental start‑up can

causeinjury.



WARNING: Handle blades carefully. They are

extremelysharp.

NOTE: The DCW682 is shipped with a 4" (102mm) diameter

blade installed. The blade used MUST be 4" in diameter and

1/8" inthickness.

In time your saw blade will wear out and need replacement.

To remove the blade, follow the stepsbelow.

1. Turn off and remove thebattery.

2. Loosen the 4torx head screws

14

from the bottom of

the shoe, using the T20 torx screwdriverprovided.

3. Rotate the shoe out of theway.

4. Use the spanner wrench provided to loosen

(counterclockwise) the blade nut. Depress the spindle

lock

10

on the top of the gear case to hold the spindle

while you unscrew thenut.

5. Remove the blade and have it sharpened or replace it

with a newone.

6. Reinstall the blade by reversing the steps above. Be sure

blade teeth point counterclockwise as shown in FigureG.

7. IMPORTANT: Always check the fine depth adjustment

when sharpening or replacing the blade. Adjust if

necessary. (Refer to TheControls).

The Controls

The heart of your biscuit joiner is the base/fence assembly.

All of the controls that let you make a variety of precision cuts

are located on this assembly. Take a few minutes to become

familiar with the various controls.

ALWAYS TURN OFF THE BISCUIT JOINER AND REMOVE THE

BATTERY BEFORE MAKING ANYADJUSTMENTS.

Adjustable Fence (Fig. H, I)

a. The adjustable fence

6

provides a sturdy, precise

reference surface to determine the point at which

the slots for the biscuits will be cut. Its adjustable

height feature allows you to position biscuit slots

as close as 3/16" (4.76mm) and as distant as 1‑3/8"

(35mm) measured from the workpiece surface to the

Introduction

Examine Figure A and your biscuit joiner for a few minutes

to become familiar with the various features and the names

used to describe them. The following sections will discuss

the various controls and you will need to know where

theyare.

Paddle Switch (Fig. A)



CAUTION: Hold the auxiliary handle and body of the

tool firmly to maintain control of the tool at start up

and during use and until the blade stops rotating.

Make sure the blade has come to a complete stop

be fore laying the tooldown.



CAUTION: Before connecting the tool to a power

source depress and release the paddle switch

1

)

once

to ensure that the switch is off. Depress and release the

paddle switch as described above after any interruption

in power supply to thetool.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start‑up can causeinjury.

Wall Mounting

Some DEWALT chargers are designed to be wall mountable

or to sit upright on a table or work surface. If wall mounting,

locate the charger within reach of an electrical outlet, and

away from a corner or other obstructions which may impede

air flow. Use the back of the charger as a template for the

location of the mounting screws on the wall. Mount the

charger securely using drywall screws (purchased separately)

at least 1” (25.4mm) long, with a screw head diameter of

0.28–0.35” (7–9mm), screwed into wood to an optimal

depth leaving approximately 7/32” (5.5 mm) of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out the

lights;

c. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

4. You may charge a partially used pack whenever you

desire with no adverse effect on the batterypack.

Charger Cleaning Instructions



WARNING:Shock hazard. Disconnectthe charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non‑metallic brush. Do not use water or

any cleaningsolutions.

Loading ...

Dewalt DCW682B 20V MAX XR BRUSHLESS CORDLESS BISCUIT JOINER Tool Only

Instructional Manual - Page 17