Loading ...
Loading ...
Loading ...
INCLINE &CONSOLE
See Page 17 for illustration
1. Install the Incline Rail Assembly (:2)into the U-channel bracket of the Main
Frame (1). Secure with the six bolts & associated hardware as follows: From
the sides install two Hex Head Bolts (133) with two Flat Washers (164) and
two Nylon Nuts (157). From the top install four Hex Head Bolts (135), four
Split Washers (182), four Flat Washers (170), and four Star Washers (183), as
shown in figure 1, and tighten with the Wrenches provided (184 & 187).
2. Connect the 3 wire harness (48) to the female receiver cable coming from the
Incline rail assembly (:2).Connect the Three pin position Sensor connector
(49) to the female receiver coming from the Incline rail assembly (2).
3. Locate the Console Mast (1:2) and Console Mast Cover (96) and slide the
Cover onto the Mast as far as it will go. Make sure the Console Mast Cover is
facing the correct way. At the top opening of the Main Frame of the
elliptical is a Computer Cable (50). Secure the free end of the twist tie that
exits the bottom of the console mast (12) to this cable. Pull the opposite end
of this twist tie up through the console mast (1:2) until the cable exits the top.
Install the Console Mast (1:2) into the receiving bracket on the top of the Main
Frame (1). Pull slightly on the computer cable at the top of the mast while
installing. This will ensure the cable does not get pinched and shorted during
console mast assembly.
4. Put one Split Washer (180) onto the Long Hex Head Bolt (1:25) and install
through the left side of the receiving bracket into the Console Mast (1:2). Put
the two Curved Washers (181) onto the two Short Hex Head Bolts (132) and
install through the front of the console mast. Using the Wrench (184), tighten
the three bolts, and the fourth bolt, which is pre-installed, firmly.These bolts
should be tightened as much as you possibly can.
5. Plug all of the connectors into the back of the console; Computer Cable (50),
two Hand pulse Cables (57), Resistance switch wire (60) and Incline switch
wire (61). Secure the Console (45) on the console mounting plate with four
Phillips Head Screws (141). Note: there will be an empty four pin port on the back of
the console. This model doesn't use this port.
#164. 3/8"x 19x 1.5T
Flat Washer (2 pcs)
#170. 5/16"x 20 x 1.ST
Flat Washer (4 pcs)
#181.3/8"x 23 x 2T
Curved Washer (2 pcs)
#180. 3/8"x 2T
Split Washer (2 pcs)
#141. M5 x lOmm
Flat Washer (4 pcs)
#157.3/8"x 7T
Nylon Nut (2 pcs)
#182.5/16"x 1.ST
Split Washer (4 pcs)
#183.5/16"
Star Washer (4 pcs)
#1:32.3/8"x 3/4"
Hex Head Bolt (2 pcs)
#135.5/16"x 2-1/4"
Hex Head Bolt (4 pcs)
#1:33.3/8"x 1-1/2"
Hex Head Bolt (2 pcs)
#125.3/8"x 2-1/4"
Hex Head Bolt (1 pcs)
HANDLEBAR
See Page 17 for illustration
1. Install two Wave Washers (175) onto the Left and Right side of the Handle Bar
axle.
2. Slide the Left (1O) and Right (11) Handle Bars onto the appropriate side of
the axle.The handlebars have a small sticker on them indicating L (left) and R
(right). Make sure the handlebars are facing the correct direction - see
illustration.
3. Place two Flat Washers (165) onto the two Hex Head Bolts (132) and
install, and tighten, in the threaded holes in the ends of the axle.
4. Connect the two wires (Left-61 to 63 & Right-60 to 6:2) on the L & R sides
together and store the excess wire, including plastic connectors, back inside
the console mast. Place the rubber grommets (75) over the wire on each side
and snap them into the holes of the console mast. Install the Handle Bar
Covers (105 & 106, 107 & 108) over the Handle Bar axle connections and
secure with the eight Sheet Metal Screws (142).
#175.25ram
WaveWasher (2 pcs)
#165.3/8"x 30 x 2T
Flat Washer (2 pcs)
#142.3.5 x 12ram Sheet
Metal Screw (8 pcs)
#1:32.3/8"x 3/4"
Hex Head Bolt (2 pcs)
#75.
Rubber Grommet (1 pc)
15 E25 / E35 ELLIPTICAL
Loading ...
Loading ...
Loading ...