Loading ...
Loading ...
Loading ...
To Install Your Cooler
• If the Beverage cooler is going to be used in an area that is prone to power
surges/outages, it is suggested that you use a power surge protector. The surge
protector that you select must have a surge block high enough to protect the
Beverage cooler it is connected to. Damages due to power surges are not considered
a manufacturer covered defect.
• This cooler is designed for free standing or built-in (fully recessed)
installation.
• Place your cooler on a solid and level floor that is strong enough to
support it when it is fully loaded. This will ensure a vibration-free and noise-free
operation. Adjust the leveling legs in and out to stabilize the cooler horizontally. If
the legs are not properly adjusted, the cooler may be unstable and result in excess
noise or vibration.
• Locate the cooler away from direct sunlight and sources of heat (stove,
heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources
may increase power consumption. Extremely cold ambient temperatures may also
cause the cooler to not perform properly.
• It is not advisable to install this cooler in moist areas or directly adjacent to a
kitchen sink, as moisture could cause premature corrosion to the components of your
new cooler.
• It is recommended you install the cooler in a place with temperatures
above 60°F (15°C) and below 90°F (32°C), and humidity is under 60%. If the
ambient temperature is above or below recommended temperatures, the
performance of the cooler may be affected. Placing your cooler in extremely cold or
hot conditions may cause interior temperatures to fluctuate, and the temperature
range of 3ºC-18ºC (37ºF-64ºF) may not be reached.
• Connect the cooler to an exclusive, properly grounded, standard electrical
supply (115 V AC only, 60 Hz), in accordance with the National Electrical
Code and local codes and ordinances. Any questions concerning power and/or
grounding should be directed toward a certified electrician.
• The cooler should always be plugged into its own individual electrical
outlet which has a voltage rating that matches the rating label on the cooler.
This provides the best performance and also prevents overloading of house
wiring circuits that could cause a fire hazard due to overheating.
• Under no circumstances should you cut or remove the third ground prong from the
power cord supplied.
• Do not use an extension cord or adapter plug. However, if you must use an
extension cord, it is absolutely necessary that it be a UL-listed, 3-wire grounding
type cooler extension cord having a grounding type plug and outlet and
that the electrical rating of the cord is 10 amperes (minimum) and 120 volts.
• Do not use a cord that shows cracks or abrasion damage along its length or at
either end.
Warning: Improper use of the grounded plug can result in the risk of electric shock.
If the power cord is damaged, have it replaced by qualified technician.
OPERATION INSTRUCTIONS
Recommended temperature settings
Beverage: 3°C -10°C (37°F - 50°F)
Sparkling Wines:5°C - 8°C (41°F - 46°F)
Dry/white Wines: 9°C - 14°C (48°F - 57°F)
Rose Wines 10°C - 11°C ( 50°F - 52°F)
Red Wines: 15°C - 18°C (59°F - 64°F)
Controls
After plugging the Beverage cooler into a wall outlet, the cooler would turn on
automatically and the LCD screen would show the temperature inside of the cooler.
After setting your desired serving temperature, allow the cooler to cool down for 3 to
4 hours before placing wine bottles in the Beverage cooler.
Press once to turn the interior light ON or OF
F.
Press to increase or press to decrease the temperature
in 1 degree.
Press once to turn ON the cooler. Press and hold for
about 3 seconds to turn OFF the cooler.
Switch the temperature display between Celsius and Fahrenheit.
08 09
Cooling Zone Temperature Range：
Beverage Refrigerator (Left Zone) 2°C -10°C (35°F-50°F )
Wine Refrigerator (Right Zone) 5°C -18°C (41°F-64°F )
Loading ...
Loading ...
Loading ...