Loading ...
Loading ...
Loading ...
17
ENGLISH
Repairs
The charger and batteries are notserviceable. There are no
serviceable parts inside the charger or batterypack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including
brush inspection and replacement, when applicable)
should be performed by a factory service center or
an authorized service center. Always use identical
replacementparts.
Tool Connect™ Chip (Fig. Q)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ Chip is an optional application for your
smart device (such as a smart phone or tablet) that connects
the device to utilize the mobile application for inventory
management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
moreinformation.
Installing the Tool Connect™ Chip
1. Remove the retaining screws
24
that hold the Tool
Connect™ Chip protective cover
22
into thetool.
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
23
.
3. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws and tighten
thescrews.
4. Refer to Tool Connect™ Chip Instruction Sheet for
furtherinstructions.
unthreaded accessory must have a 7/8" (22 mm)
arbor hole. If it does not, it may have been designed
for a circular saw. Use only the accessories shown in
the Accessories Chart of this manual. Accessory
ratings must always be above tool speed as shown on
toolnameplate.
WARNING: Handle and store all abrasive wheels
carefully to prevent damage from thermal shock, heat,
mechanical damage, etc. Store in a dry protected area
free from high humidity, freezing temperatures or
extreme temperaturechanges.
Accessories
WARNING: Since accessories, other than those offered
by DEWALT, have not been tested with this product,
use of such accessories with this product could be
hazardous. To reduce the risk of injury, only DEWALT
recommended accessories should be used with
thisproduct.
WARNING: Do not use a bonded abrasive wheel that
is past its expiration (EXP) date as marked near center
of wheel, if provided. Expired wheels are more likely to
burst and cause serious injury. Store bonded abrasive
wheels in dry location without temperature or humidity
extremes. Destroy expired or damaged wheels so they
cannot beused.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact DEWALT. Call 1-800-4-DEWALT
(1-800-433-9258) or visit our website: www.dewalt.com.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing thisprocedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into aliquid.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Your DEWALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regularcleaning.
To pair your tool using Wireless Tool Control™, depress
the trigger switch
1
and the Wireless Tool Control™
pairing button on the seperate device. An LED on the
seperate device will let you know when your tool has been
successfullypaired.
The capacity of this tool is 7"(180mm) and 9" (228mm)
diameterx1/4" (6mm) thick grinding or 3/16" (5mm) thick
cutting wheels. It is important to choose the correct guards,
backing pads and flanges to use with grinder accessories.
Refer to the Accessories Chart for information on choosing
the correctaccessories.
WARNING: Accessories must be rated for at least
the speed recom mended on the tool warning label.
Wheels and other accessories running over their
rated accessory speed may fly apart and cause injury.
Threaded accessories must have a 5/8"‑11 hub. Every
Register Online
Thank you for your purchase. Register your product nowfor:
• WARRANTY SERVICE: Registering your product will help
you obtain more efficient warranty service in case there is
a problem with yourproduct.
• CONFIRMATION OF OWNERSHIP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
ofpurchase.
Loading ...
Loading ...
Loading ...