Loading ...
Loading ...
Loading ...
Setting Warmer Drawer ControHs Of Equipped)
Arranging Warmer (Warm & Ready TM) Drawer Rack Positions
Tile rack can be used in 2 ways:
Inthe upright position to allow low profile food items to be placed both under
and on top of the rack (for example, rolls or biscuits on top of the rack and a
casserole dish underneath).
Inthe downward position to allow you to place light weight food items and
empty dishware (for example, rolls or pastries and dinner plates) on the rack.
Set the Warmer Drawer Rackin either position as shown below (Figure 1).
Operating the Warmer Drawer
The purpose of the Warmer Drawer is to keep hot cooked foods at serving
temperatu re. Always start with hot food. It isnot recommended to heat cold food in
the Warmer Drawer. All food placed in the Warmer Drawer should be covered with
a lid or aluminum foil to maintain quality. Do not use pJastic wrap to cover food.
PJastic may melt onto the drawer and be very difficuJt to dean. Use only
utensils and cookware recommended for oven use in the Warmer Drawer.
Always usepotholders or oven mitts when removing food from the
Warmer Drawer ascookware and plates will be hot and you can be burned.
Warmer Drawer Temperature Selection
Recommended Warmer Drawer settingstable isshown in Figure2. If aparticular food
isnot listed, start with the MED setting. If more crispness isdesired, remove the lid
or aluminum foil from the food. Most foods can be kept at serving temperatures on
the MED setting. When a combination of foods are to be kept warm (for instance,
meat with 2 vegetables and rolls), usethe Ht setting. To avoid heat loss,do not open
the Warmer Drawer while in use.
To Set the Warmer Drawer Controls:
The control and indicator lights for the Warmer Drawer features are located on the
control panel. The temperatures are approximate, and are designated by Ht (high),
MFD (medium) and LO (low).
1. Touch tile 0_/of_pad attheWarmer Drawer control position. Tile Warmer Drawer
indicator light will flash. Note: If no further pads are touched within 25 seconds
the request to power the Warmer Drawer ON will clear.
2. Setthe desired power leveI. Touch A oncetoturnONthepowerlevelforHI
(seeFigure 2)or V to turn ONthe power levelfor LO(seeFigure4). TheWarmer
Figure 1
Drawer indicator light located beside the _ pad will turn ON steady.
3. Eachtouch of tile V or A padswill decrease or increase through 6 power levels from NJ(see
Figure 2) to MED (see Figure 3) to LO (see Figure 4). Note: For best results, preheat the Warmer
Drawer before adding the food. An empty drawer will preheat in approximately 15 minutes.
4. When the food isready for removal, touch the 0_/0_pad once to turn theWarmer Drawer OFF.Tile
Warmer Drawer indicator light will turn OFF.
Note: The Warmer Drawer is inoperable
during the self-dean cycle.
hi@ MO M©
@ © ©
reed 0 reed 0 reed ©
0 @ ©
Ioe moo IoO
Figure 2 Figure 3 Figure 4
Warmer Drawer Rack
in upward position
Warmer )rawer Rack
in downward position
Warmer Drawer recom-
mended Food Settings Table
Note: The warmer drawer isequipped with
a catch which may require extra force when
opening and closing tile drawer.
Food Item Setting
Bacon HI
Hamburger Patties HI
Poultry HI
Pork Chops HI
Fried Foods HI
Pizza HI
Gravies MED
Casseroles MED
Eggs MED
Roasts (Beef, Pork, Lamb) MED
Vegetables MED
Biscuits MED
Rolls, hard MED
Pastries MED
Rolls(soft) LO
Empty Dinner Plates LQ
Figure 2
s
O [:
'!//_ !/('_"
/4_o'
Figure I
14
Loading ...
Loading ...
Loading ...