Loading ...
Loading ...
Loading ...
8
LOCATING THE POWER UNIT
• Locate the power unit away from the general living area in
an accessible location for cleaning and maintenance.
• Locate the power unit within 6 feet of a grounded electrical
outlet.The power unit requires a 120 VAC power source,
dedicated 15-amp branch circuit.
• Do not locate the power unit close to a source of extreme
heat (i.e.: water heater) or in an area with a high ambient
temperature (i.e.: attic, furnace room).
• If the power unit is located in a closet or a small utility
room, make sure the area is well-ventilated (e.g.: with door
louvers).
CHANGING INTAKE LINE DIRECTION
The intake line connects to the right side of the unit. However,
it is possible to change this configuration; to connect the intake
line to the left side of the unit, follow these steps:
Remove debris pail from power unit by releasing both latches
on sides of the unit, pulling them out and then pushing up.
Detach the pail from unit.
NC1500, NCKIT1500,
NCKIT1500HD,
HHKIT550A,
HHKIT550E, NT550A
and NT550E only:
Grasp the edges of
the bag collar and
pull down; the bag will
slide off easily. Do not
pull on the bag. Set
the bag aside.
NC1500, NCKIT1500,
NCKIT1500HD,
HHKIT550A,
HHKIT550E, NT550A
and NT550E only:
Using a Phillips
screwdriver no. 2,
remove the screw
tightening the bag
adapter and intake
elbow junction.
Disassemble the
bag adapter from the
intake elbow and set aside with its screw and nut.
All units: Disassemble
the intake elbow from
the back of the unit
using a 3/8” socket to
remove both retaining
nuts and screws.
All units: Flip the
intake elbow 180°,
then reassemble it to
the unit, taking care to
keep its gasket at its
original position.
NOTE: Ensure the
gasket is not folded in
order to prevent lack
of suction, and noise.
NC1500, NCKIT1500,
NCKIT1500HD,
HHKIT550A,
HHKIT550E, NT550A
and NT550E only:
Reassemble the bag
adapter to the intake
elbow. Align triangle
with small inclined
stud, then tighten
the junction using
the screw and nut
previously removed
in .
NC1500, NCKIT1500,
NCKIT1500HD,
HHKIT550A,
HHKIT550E, NT550A
and NT550E only:
Put the bag back in
place by grasping
the edges of its collar
and insert over bag
adapter. Be careful
not to tear the bag.
Ensure the collar is
positioned between
the taper ring and the
bag stopper on the bag adapter.
All units: Put the debris pail back in place.
POWER UNIT INSTALLATION
AD0076
AO0078
NC1500, NCKIT1500, NCKIT1500HD,
HHKIT550A, HHKIT550E, NT550A AND
NT550E ONLY
AD0077
AD0078
NC1500, NCKIT1500, NCKIT1500HD,
HHKIT550A, HHKIT550E, NT550A AND
NT550E ONLY
AO0080
NC1500, NCKIT1500, NCKIT1500HD,
HHKIT550A, HHKIT550E, NT550A AND
NT550E ONLY
TAPER RING
BAG STOPPER
AD0075
WARNING
!
Do not install outdoors. Before being hung, rest the
unit on a leveled surface to prevent the unit to fall
down. When performing installation, servicing or
cleaning the unit, it is recommended to wear safety
glasses and gloves.
NC1500, NCKIT1500, NCKIT1500HD,
HHKIT550A, HHKIT550E, NT550A AND
NT550E ONLY
Loading ...
Loading ...
Loading ...