Loading ...
Loading ...
Loading ...
10
11. TROUBLESHOOTING
Problem Cause Solution
There is water in the drip tray
(A8)
This water comes from the internal circuits of
the machine and is a normal consequence of
their operation
Empty and clean the drip tray on a regular basis
No espresso coee is
delivered
No water in the water tank (A2) Fill the water tank
Blockage in the cups lter (A15) or (A16) Rinse the lters under running water
The water tank (A2) is not properly in place and
the valves at the bottom are not open
Press down lightly on the tank to open the valves at
the bottom
Limescale in the water circuit Descale the appliance
The espresso coee drips from
the edges of the lter holder
(A14) rather than the holes
The lter holder has been inserted incorrectly
or is dirty
Attach the lter holder correctly and rotate rmly as
far as it will go
The coee spout gasket has lost elasticity or
is dirty
Clean the coee spout gasket. Have the coee spout
gasket replaced by Customer Service
The lter holder (A14) cannot
be attached to the machine
Too much coee has been placed in the lter
Use the measuring scoop (A18) supplied and make sure
you are using the correct lter for the type of preparation
The coee crema is too light
(delivered from the spout
too fast)
The pre-ground coee is not pressed down
rmly enough
Tamp the pre-ground coee more rmly
There is not enough pre-ground coee Increase the quantity of pre-ground coee
The pre-ground coee is too coarse
Use only pre-ground coee for espresso coee makers
The wrong type of pre-ground coee is being used
Change the type of pre-ground coee
The coee froth is too dark
(delivered from the spout too
slowly)
The pre-ground coee is pressed down too rmly
Press the coee down less rmly
There is not enough pre-ground coee Reduce the quantity of pre-ground coee
The espresso coee spout (A7) is blocked Clean the coee spout
The cup lter (A15) (A16) is blocked Clean the cup lter
The pre-ground coee is too ne
Use only pre-ground coee for espresso coee makers
The pre-ground coee is too ne or damp Use pre-ground coee for espresso coee makers
only and make sure it is not too damp
After delivering coee, the
lter remains attached to the
coee spout
Insert the lter holder (A14) again, deliver coee,
then remove the lter holder
The machine will not make
any drinks and the water tank
light is on
No water in the water tank (A2) or no water
tank in the machine
Fill the tank with water or insert the water tank
The water tank indicator (B2)
blinking and steam indicator
is on (B4).
Air in the hydraulic circuit Verify water tank position and water presence.
Place a container under steam wand (A5).
Turn the steam dial (A4) and wait until delivery from
steam wand stops, then close steam dial.
The machine will not make
any drink and all the lights
except (B1) blink
The steam dial (A4) is open Close the steam dial (A4)
The machine will not make
any drink and all the lights
ash for a few seconds
No water in the water tank (A2) Fill the tank with water
The water tank (A2) is not properly in place and
the valves at the bottom are not open
Press down lightly on the tank to open the valves at
the bottom
The machine does not function
and all the lights ash
Disconnect the machine immediately and contact
authorised Customer Services.
No milk froth is formed when
making cappuccino
Milk not cold enough Always use milk at refrigerator temperature
Steaming procedure could be wrong Review the “making milk beverage” paragraph
Frother dirty Clean the steam wand (A5)
Water sensor in the water
tank is not working properly
Water tank is dirty Clean the water tank internally, and dry the back
panel
Descaling led is on Descaling is required Perform descaling
Loading ...
Loading ...
Loading ...