Loading ...
Loading ...
Loading ...
22 HexaPlate User Manual Lifepro
Vibration Therapy Collection 23
CLEANING AND STORAGE
WARNING: Always unplug the power cord and allow the machine to cool
before cleaning, moving, or storing.
• Use a slightly damp cloth to wipe away dirt or moisture.
WARNING:
Do not allow water or other liquids to come into contact with the device.
Do not immerse the device in water or other liquids.
• Do not use harsh detergents or abrasive, solvent, or chemical cleaners.
• Store in a cool, dry, indoor location. Store in a well-ventilated area, free
of dust, and out of direct sunlight.
• When storing for a long time, remove the batteries from the remote
control and cover the machine to keep out dust and dirt.
• Do not attempt to disassemble or repair; the device contains no
user-serviceable parts.
NOTICE
• This product is intended for in-home use only. Do not use the product in any
commercial, rental, institutional, or therapeutic setting This product is intended for
indoor use only.
• To avoid damage to flooring or carpet, place a non-slip rug or exercise mat under
the machine.
• Dispose of the product and all parts according to local and federal regulations.
• Unplug the device immediately in the event of a power failure.
• Keep sharp objects away from the product to avoid damaging it.
TROUBLESHOOTING GUIDE
Quickly troubleshoot simple issues you might experience using the table
below. Please contact us for additional assistance at (800) 563-6604 or
support@lifeprofitness.com.
ISSUE POSSIBLE REASON HOW TO RESOLVE
THE MACHINE IS
NOT WORKING.
Machine is not turned on.
Flip the power switch on the
front of the machine to the ON
position.
The control panel is not on.
Press the On/Off button on the
remote control to turn on the
control panel.
THE MACHINE
STOPPED
WORKING
SUDDENLY.
The vibration plate
automatically shuts off
after the set working time.
Turn the machine on again to
begin a new workout program.
When the machine has
been working for a long
time, the motor shuts off
for overheating protection.
Allow the machine to cool for
at least 30 minutes before
using again.
THE REMOTE
CONTROL DOES
NOT WORK.
The remote control is too
far away from the infrared
sensor on the control
panel.
Point the remote control
directly at the infrared sensor
when in use. The effective
distance is approximately
6 feet.
Batteries are installed
incorrectly.
Check to see if the batteries
are installed per the polarity
markings on the inside of the
battery compartment.
Batteries are dead.
Replace dead batteries with
two new AAA batteries.
CANNOT TURN
MACHINE OFF
USING REMOTE
CONTROL OR
CONTROL PANEL
The HexaPlate must be
powered off via the Power
switch.
Flip the Power switch on the
front of the machine to the
OFF position.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Loading ...
Loading ...
Loading ...