Loading ...
Loading ...
Loading ...
18
19
LIGHT POSSIBLE CAUSE REMEDY
LAMPEGGIANTE
The infuser has not been replaced after
cleaning.
Insert the infuser as described in the section “Cleaning
the infuser”.
The inside of the appliance is very dirty. Clean the inside of the appliance thoroughly, as described
in the section “Cleaning and maintenance”.
If the message is still displayed after cleaning, contact a
customer services.
TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.
PROBLEM POSSIBLE CAUSE REMEDY
The coee is not hot
The cups were not preheated. Warm the cups by rinsing them with hot water (Please note
you can use the hot water or rinse function).
The infuser has cooled down because 2/3 minutes have
elapsed since the last coee was made.
Before making the coee, warm the infuser by pressing the
rinse button .
The coee is thin or not
creamy enough.
The coee is ground too coarsely. Turn the grinding adjustment dial one click anticlockwise
while the coee mill is in operation (g. 8).
Continue one click at a time until coee delivery is
satisfactory. The eect is only visible after delivering two
coees (see the section: “Adjusting the coee mill” on
page 13).
The coee is unsuitable. Use pre-ground coee for espresso coee makers.
The coee is delivered too
slowly or a drop at a time
The coee is ground too nely. Turn the grinding adjustment dial one click clockwise while
the coee mill is in operation (g. 10). Continue one click at
a time until coee delivery is satisfactory. The eect is only
visible after delivering 2 coees (see the section: “Adjusting
the coee mill” on page 13).
Coee does not come out of
one of the spouts
The spouts are blocked. Clean the spouts with a toothpick.
The frothed milk has large
bubbles
The milk is not cold enough or is not semi-skimmed. You should ideally use skimmed or semi-skimmed milk at
refrigerator temperature (about 5°C).
If the result is still disappointing, try another brand of milk.
The milk is not frothed
Cappuccino maker dirty. Clean as described in the section "Cleaning the cappuccino
maker after use" on page 13.
Steam delivery stops during
use
A safety device stops steam delivery after 3 minutes. Wait a few minutes, then activate the steam function
again.
The appliance does not
come on
It is not plugged into the mains socket. Plug into the mains socket.
The main switch (A8) is not turned on. Place the main switch in the I position (g. 1).
EXPLANATION OF LIGHTS
LIGHT POSSIBLE CAUSE REMEDY
FLASHING
Insucientwaterinthetank. Fill the tank with water and insert it correctly, pushing it as
far as it will go until it clicks into place.
The tank is not correctly in place. Insert the tank correctly and press as far as it will go.
FLASHING
The grounds container (A13) is full. Empty the grounds container and drip tray, clean and
replace. Important: when removing the drip tray, the
grounds container MUST be emptied, even if it contains
few grounds. If this is not done, when you make the next
coees, the grounds container may ll up more than
expected and clog the machine.
After cleaning, the grounds container has
not been replaced.
Remove the drip tray and insert the grounds container.
FLASHING
The grinding is too ne and the coee is
delivered too slowly or not at all.
Repeat coee delivery and turn the grinding adjustment
dial (g. 10) one click clockwise towards “7” while the
coee mill is in operation. If after making at least 2 coees
delivery is still too slow, repeat the correction procedure,
turning the grinding adjustment dial another click until
delivery is correct (see the section: Adjusting the coee mill
on page 12). If the problem persists, turn the steam dial to
the I position and deliver water from the cappuccino maker.
FLASHING
The "pre-ground coee" function has been
selected without placing any pre-ground
coee in the funnel.
Place pre-ground coee in the funnel or deselect the
"pre-ground" function.
FLASHING
The machine must be descaled. The descaling procedure described in the section
“Descaling” needs to be performed as soon as possible.
FLASHING
Too much coee has been used. Select a milder taste or reduce the quantity of pre-ground
coee then make the coee again.
FLASHING
The coee beans have run out. Fill the beans container
The pre-ground coee funnel is clogged. Empty the funnel with the help of a knife as described in
the section "Cleaning the pre-ground coee funnel".
Loading ...