Loading ...
Loading ...
Loading ...
13
ENGLISH
Storage Bins
The storage bins
16
and
17
can be connected horizontally
or stacked vertically for convenientstorage.
Stacking Storage (Fig. G)
1. Line up the bump
18
of the top bin with the recess
19
of the bottombin.
2. Place the first bin on top of the second bin so it is engaged
with the stop ribs
20
to prevent shifting. The bins will not
lock together so tipping may dislodge thebins.
NOTE: It is not recommended to stack higher than twobins.
NOTE: Two small bins can be stored on top of a largebin.
Side-by-Side Storage (Fig. H)
1. Slide the storage bin connector
21
onto the storage bin
channel
22
of one bin until it clicks into place and issecure.
2. Slide the channel of a second bin along the connector
until it clicks into place and issecure.
NOTE: It is not recommended to connect two large bins side
byside.
Charging in Storage Bin (Fig. I)
1. Place the charger connector
14
into the connector detent
56
of the large bin
17
.
2. Run the charger cord
13
through the cord channel
57
of the bin and out of the charging notch
23
.
3. Lay the unit in the bin so the charging pegs
7
on the
unit fully engage with the chargerconnector.
Proper Hand Position (Fig.F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Hold the appliance
1
so your palm presses down the unlock
button
2
and use your thumb or a finger to push down the
powerbutton
3
.
Speed Control (Fig.E)
The appliance has a variable‑speed dial
4
. Turn the dial to
the appropriate speed for the attachment being used (1 is
the lowest speed, 5is the highestspeed).
ATTACHMENT SPEED
Immersion Blender Start at 1, increase as needed
Wine Opener 5
Can Opener 5
Spice Grinder 5
Whisk Start at 1, increase as needed
Frother Start at 5, decrease as desired
NOTE: With a 5‑second delay before the unit turns off, you
can release the buttons and use your thumb to adjust speed
without turning the unitoff.
On / Off (Fig.D)
IMPORTANT: Never turn the motor on unless attachments
are securelyattached.
NOTE: Optimal temperature for use is between 50–104°F
(10–40°C).
1. To turn unit on, either:
‑ Press unlock button
2
, then press power button
3
.
‑ Press power button, then press unlockbutton.
‑ Press unlock and power buttonssimultaneously.
NOTE: There is a slight delay between pressing both buttons
and the appliancestarting.
2. When the appliance is ready to use, the LEDs
5
will
illuminate and remain solid. If they do not, refer to the
TROUBLESHOOTINGsection.
NOTE: If LEDs go off during use, or don't light when starting
unit, release buttons and go back to step1.
3. Once the unit is on, the buttons may be released for up to
5seconds. The motor will stop running after the buttons
are released but the appliance remains active for 5seconds.
As long as the power button is pressed at least once within
5seconds after releasing, the appliance will turn backon.
4. To turn off, release both buttons. The appliance will
remain active for 5seconds before turningoff.
WARNING: The LEDs will stay on after buttons are
released. Ensure the LEDs are off and the unit has fully
stopped before removingattachments.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and keep hands away from
the switch before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can causeinjury.
Installing and Removing Attachments (Fig.C)
WARNING: Ensure LEDs are off and the system is noton.
Blender / Wine Opener / Can Opener / Spice Grinder
1. To install, slide the attachment head
55
of the attachment
onto the motor
6
and turn clockwise (as viewed from the
end of the attachment) until it securely locksin.
NOTE: The attachment can be installed on the motor in four
different locations, so it does not need to be placed in any
one specificorientation.
2. To remove, turn counterclockwise and pull attachmentoff.
Whisk / Frother
1. To install, slide the whisk pole
55
or frother pole
57
into
the adaptor hole
9
until it clicks into place and issecure.
2. Slide the adaptor
8
onto the motor
6
and turn
clockwise (as viewed from the end of the attachment)
until it locks insecurely.
NOTE: The attachment can be installed on the motor in four
different locations, so it does not need to be placed in any
one specificorientation.
3. To remove, turn adaptor counterclockwise and pull it off,
then pull the whisk or frother from theadaptor.
Loading ...
Loading ...
Loading ...