Loading ...
Loading ...
Loading ...
11
PROGRAMMING VEHICLE SYSTEMS
B. Press the chosen HomeLink button for two seconds and release. Press
that same button again for two seconds and release. The long LED
will ash blue and then turn o.
C. Press the HomeLink button a few more times until door moves.
NOTE:
For additional instructions, see the motor vehicle manual,
www.homelink.com or visit www.GenieCompany.com
Step 1 Clear HomeLink
Clear HomeLink by pressing and holding down the rst and third
buttons until the indicator on the
HomeLink blinks slow and then fast
for 20 seconds; then release both
buttons.
NOTE: Clearing the HomeLink will
remove all previously programmed garage door openers.
Step 2 Train HomeLink to the Genie Remote
Choose the button on the HomeLink that will be used to open
the door.
NOTE:
Hold the Genie Remote two
inches from the HomeLink button.
Hold down the Genie remote button. While holding, press and
hold the chosen HomeLink button.
Hold down both buttons until the indicator on the HomeLink
blinks slow then fast. Once it blinks, release both buttons.
Programming HomeLink® System Programming Car2U
®
System
Step 1 Clear Car2U to default settings
The default setting for the Car2U system is:
t#VUUPO(FOJF¥.BOVGBDUVSFE0QFOFST
t#VUUPO-JGU.BTUFS¥.BOVGBDUVSFE0QFOFST
t#VUUPO8BZOF%BMUPO¥.BOVGBDUVSFE0QFOFST
A. Press and hold buttons 1 and 3 for 20 seconds or until all three
LEDs begin to ash.
B. Release both buttons. The Car2U system is now set to the
Factory Default settings
NOTE:
Clearing the Car2U remote will remove all previously
programmed garage door openers.
Step 2 Program Car2U to the Genie Opener
(Place opener into programming mode)
A. Press and hold the PROGRAM button on the opener
until the round blue LED is ON—release the button.
The long purple LED will begin
ashing.
B. Press the designated Genie Car2U button for two
seconds and release. Press that same button again
for two seconds and release. The long LED will ash
blue and then turn o.
C. Press the Car2U button a few times more until door moves.
PRGM
SET
PRGM
SET
1. Press and hold the program button on the powerhead
until the round LED turns blue, then release.
2. The round LED will go out and the long LED will begin
ashing purple.
3. Complete programming steps.
PUTTING OPENER INTO PROGRAMMING MODE:
NOTE: The openers LEARN LED will time out in 30 seconds.
Programming must be completed within 30 seconds.
Solid Blue
PRESS
&
RELEASE
Flashing Purple
Step 3 Program HomeLink to the Genie Opener
(Place opener into programming mode)
A. Press and hold the PROGRAM button on the opener until the
round blue LED is ON. Release the button. The long purple
LED will begin ashing.
Step 3 Changing Factory Default Button for a Genie
Opener
A. Press and hold buttons 1 & 3 for ONE SECOND and
release—all three LEDs will light solid red.
B. Press and hold the button (2 or 3) to change it to
Genie—the corresponding LED will ash. While
continuing to hold that button, press and release
button 1. Press and release button 1 again.
C. Release the button being held in step B and wait for
the LED to stop ashing. This button is now set for
Genie. Repeat Step 2 for second Genie Opener.
NOTE:
For additional instructions see the motor vehicle manual,
learcar2u.com or visit www.GenieCompany.com
PRGM
SET
PRGM
SET
1. Press and hold the program button on the powerhead
until the round LED turns blue, then release.
2. The round LED will go out and the long LED will begin
ashing purple.
3. Complete programming steps.
PUTTING OPENER INTO PROGRAMMING MODE:
NOTE: The openers LEARN LED will time out in 30 seconds.
Programming must be completed within 30 seconds.
Solid Blue
PRESS
&
RELEASE
Flashing Purple
Loading ...
Loading ...
Loading ...