Loading ...
GETTING STARTED
ASSEMBLY
Fully assemble product prior to use.
1
Insert the Upper Handle into Upper Handle Pole
and insert Upper Handle Pole into the base.
You will hear a “CLICK” when each end locks
into place.
2
Slide the Clean Water Tank into place. Push
down firmly.
NOTE:
To avoid damage to wood floors
underneath area rugs or carpet, place
waterproof material (ex: plastic) underneath
them before cleaning.
BEFORE YOU BEGIN CLEANING
Vacuum carpet and upholstery
thoroughly with a Hoover® vacuum
before use. Don’t use the carpet
cleaner as a traditional vacuum
cleaner.
Be sure to check Hoover Cleaning
Solutions Guide and the cleaning
code on your upholstery. Use your
cleaner only on upholstery marked
“W” or “W/S”.
Test for colorfastness in a small,
hidden area. Gently rub surface with
a dampened white cloth. Wait ten
minutes and check for color removal
or bleed with a white paper towel.
1
2
3
TIP
OPERATION
FILL THE CLEAN WATER TANK
1
Lift up to remove the Clean Water Tank, then
remove the cap and add warm water to the fill
line. Add Hoover Solution to the solution fill
line. Secure cap.
2
Align the tank and firmly press it into place.
NOTE:
Cap must be locked in place for
proper performance and to prevent leaking.
NOTE:
Read the directions on the
Hoover® Carpet Cleaning fluid prior to use.
CLEANING FLUID
SEE THE HOOVER’S SOLUTION GUIDE insert or visit
Hoover.com/cleaning-solutions.
CAUTION:
Not to be used for
grooming a pet.
CAUTION:
DO NOT USE THIS EXTRACTOR
ON HARD FLOORS. USING THIS PRODUCT ON
HARD FLOORS MAY SCRATCH OR DAMAGE YOUR
FLOOR.
HOW TO CLEAN CARPETS
12
1
Step on the Handle Release Pedal to recline the
cleaner into position.
2
Step on the Power Pedal to turn ON.
IMPORTANT:
Empty Dirty Water Tank
when you hear an audible change. Ensure the
tank is secured before cleaning.
3
Squeeze trigger for a slow forward and
backward wet stroke.
4
Release trigger for a slow forward and
backward dry stroke.
To Rinse: Fill with warm water and omit adding
solution to the Clean Water Tank.
WARNING:
Risk of personal injury –
Brushroll may suddenly restart – unplug before
cleaning or servicing.
HOW TO CLEAN THE DIRTY
WATER TANK
To Dry System: Run system for ten seconds
before shutting o without engaging trigger.
1
Turn power OFF and unplug the power cord.
2
Press down the top of the Dirty Water Tank.
Remove Tank from carpet cleaner base at an
angle.
3
Place on a flat surface and unlatch Dirty Water
Tank lid to remove top of tank.
4
Empty tank, rinse, and remove all large debris
from tank and openings. Allow tank to air dry.
5
Prior to replacing tank, check and clean filter
as needed.
CAUTION:
Always turn off this
product before connecting or disconnecting
hose.
HOW TO ATTACH/USE HOSE AND
TOOL
1
Read “Before you Begin Cleaning” instructions.
2
To ensure maximum performance and to
protect your carpet, be sure to place the handle
in the upright position while using the hose.
Placing the handle in the upright position shuts
o the antimicrobial embedded brushroll.
3
To clean with hose tool, remove the nozzle
cover then align the ports and plug it in firmly.
4
Connect tool to hose by sliding it onto the
connector until it securely locks into place.
CLEANING CARPETED STAIRS
AND UPHOLSTERY
CAUTION:
Use extra care when
cleaning on stairs. To avoid personal injury
or damage, and to prevent the cleaner from
falling, always place cleaner at bottom of
stairs or on floor. Do not place cleaner on
stairs or furniture, as it may result in injury
or damage.
1
Hold tool about 5 inches over the spot or stain.
Spray a generous amount of cleaning solution
over the soiled area by pressing the trigger
behind the tool.
Tools and accessories vary per model.
Loading ...
Loading ...
Loading ...