Loading ...
Loading ...
Loading ...
iS "
thel_pe slill hot to obtainsmcx_h, Pohaed ends.
14. Ins_ one _I of the Rope throu_ the Handle and
sccu.,€ with a imot.
_. tmcmt_ o(_ €od_d_ Ror)€_ tl_RO_ Exit
Hole, intothe'msideoftheHousi_, intothePulley,
and up through the Pulley Hole. See Inset, Figure 30.
16. Wrap ROpe counterclockwise around the Pulley
Ratchet and tuck loose end under Ropewhere itcomes
out of the Pulley Hole. Leave a l-inch tail laying flat
on top of the Pulley between the Retainer Rj'band the
rope Retention Screw/Post. Figure 30.
17. Reinstall the Rope Retention Screw into the reten_
fion post. Tightenuntil snug.
NOTE: Do not overtighten the Screw. Overtighten-
ing _ screw can cause the threads in the scow post
to strip out.
"18, Hold Rope taut at Rope Exit Hole so it will not move
and remove hex wrench.
19 Slo_vly feed rope into the Pulley Housing.
20. Make sure Spacer is in place as shownin Figure 29,
then re_r_ steps to re-assemble.
..... the nut just until the beveled _her is flattened
against the dutch. Over or under tightening the nut
e "
_: cancause ngme damage.
_l .................. ,,11HII I | II ,, IIl,II
n. m. xn)t v rw sn -r uJBnacA oN
• Lubricate the Flexible Drive Shaft:
-- After each ten (10) hours ofoperation.
Before operating if the unit has been stored for
• 90 days or longer.
• Use Flex Shaft Lube Part No. 530-030102.
NOTE: A tube of'Flex Shaft Imbe" has been supplied
with your unit to be used after the first 10 hours of
operation.
....• Use the following p_rocedure for bes_Jresults:
flex.A hotmuffler cancause serious burns..
[€_rrloN:l Laythe _ drive slmtton adeansur-
Avoid hying the shaft on the floor, ground,oron
any sui-face that may have dirt or debris. Even after
•:wiping the shaft, grease residue can pick up dirt par-
ticks that can cause damage or l)_nmture failur_
Figure 3x Figure3z
|!OUS!N(;
NOTCH
,,,, ,
CIRCLE
Take care to avoid injuring your hands
and fingers with broken wires when checking for
damage or wiping the flexible drive shaft. A cloth will
not prevent the broken wires from pun_turlng or tear-
ing your skin.
i. Remove the Screw and Nut in the Throttle Trigger
Housing as shown in Figure 2.
2. Hold the Trigger away from the Drive Shaft Housing and_
rerm_vc the barrel end of the Cable from the Trigger as
shown in Figure 3.
!¢Ao'noN:J Donot bendthecable;, _ ,, _
4. Loosen (but do not_) the Hex Screws and
remove the Drive Sha_ Housing from the Clutch
Shrou& Ngure I.
5. Remove the Flexible Drive Shaft from the .Drive
Shaft Housing as shown in Figure 3I.
6. Check the Flexible DriveShaft for broken wires,twists,
or kinks and replace if damage is fiydnd.
7. Using a clean cloth, wipe the surface of the Flexible
Drive Shaft thoroughly to remove any old grease.
F_igu_32.
,.. ....... .:-2._j-. e
8. Apply a uniform coat ofhbe to the entire su trace ofth
Flexible Drive Shaft.
9. Inject the_remainingcontents 0fthe tube into thetopo f
the Drive Shaft Housing.
10. Replace Flexible Drive Shaft in the Drive Shaft
Housing.
U" Follow the instructions in "Assembly" to reinstall the
Throttle Cable and the Drive Shaft Housing.
iiiii iiii ii i iiiiii iii '
Loading ...
Loading ...
Loading ...