Loading ...
Loading ...
Loading ...
12 13
ELECTRICAL CONNECTION (continued) ELECTRICAL CONNECTION (continued)
The squeeze connector MUST be installed
before reinstalling the terminal block cover.
Power Cord
Strain Relief
Terminal
Block
Bracket
E. Replace wire cover on range back
and replace the screws removed
earlier. Make sure that no wires are
pinched between cover and range
back. Replace the terminal block
cover if it was removed.
Squeeze
Connector
Terminal Block
Conduit
Bracket
4-Wire Cable from Home Power Supply
IMPORTANT: The neutral wire of the supply
circuit must be connected to the neutral
terminal located in the lower center of the
terminal block. The power leads must be
connected to the lower left and the lower
right terminals of the terminal block. The
grounding lead must be connected to the
frame of the range with the ground plate
and the green ground screw.
BEFORE: POWER CORD AND CONDUIT
Terminal
Block
Neutral
Terminal
Ground
Strap
Ground Strap
or
FOR POWER CORD
INSTALLATION
A. Remove the 3 lower terminal screws
from the terminal block. Remove
the ground screw and ground plate
and retain them. Cut and discard the
ground strap. DO NOT DISCARD ANY
SCREWS.
B. Insert the one ground screw into the
power cord ground wire terminal ring,
through the ground plate and into the
frame of the range.
C. Insert the 3 terminal screws (removed
earlier) through each power cord terminal
ring and into the lower terminals of the
terminal block. Be certain that the cen-
ter wire (white/neutral) is connected to
the center lower position of the terminal
block. Tighten screws securely into the
terminal block. Do not overtighten the
screws.
After: Power Cord
Terminal
Block
Neutral
Terminal
Ground Plate
(grounding to
range)
Ground
Screw
FOR CONDUIT INSTALLATION
A. Loosen the 3 lower terminal screws
on the terminal block. Strip wire to
exposed tip about 5/8" long.
B. Insert the center (white/neutral) wire
tip through the bottom center terminal
block opening. On certain models, the
wire will need to be inserted through
the ground strap opening and then into
the bottom center block opening. Insert
the two side bare wire tips into the low-
er left and the lower right terminal block
openings.
C. Tighten the screws until the wire is
firmly secured (35 to 50 inch-lbs.). Do
not overtighten the screws.
After: Conduit
Terminal
Block
Ground Plate
(Grounding to Range)
Wire
Tips
Ground Screw
NOTE: ALUMINUM WIRING: Aluminum
building wire may be used but it must be
rated for the correct amperage and voltage.
3-WIRE CABLE FROM HOME POWER
SUPPLY
IMPORTANT: The neutral or ground wire of
the power cord must be connected to the
neutral terminal located in the lower center
of the terminal block and the ground strap
must connect the neutral terminal to the
ground plate. The power leads must be
connected to the lower left and the lower
right terminals of the terminal block.
DO NOT remove the ground strap con-
nection.
FOR POWER CORD INSTALLATION
A. Remove the 3 lower terminal screws
from the terminal block.
B. Insert the 3 terminal screws through
each power cord terminal ring and
into the lower terminals of the terminal
block. Be certain that the center wire
(white/neutral) is connected to the cen-
ter lower position of the terminal block.
C. Tighten screws securely into the
terminal block. DO not overtighten the
screws.
FOR CONDUIT INSTALLATION
A. Loosen the 3 lower terminal screws on
the terminal block. Strip wire to expose
tip about 5/8" long.
B. Insert the center (white/neutral) wire
tip through the bottom center terminal
block opening. On certain models, the
wire will need to be inserted through
the ground strap opening and then into
the bottom center block opening. Insert
the two side bare wire tips into the low-
er left and the lower right terminal block
openings.
C. Tighten the screws until the wire is
firmly secured (35 to 50 inch-lbs.). Do
not overtighten the screws.
NOTE: Aluminum Wiring: Aluminum build-
ing wire may be used but it must be rated
for the correct amperage and voltage.
Power Cord
Ground Strap
Power Cord
Neutral
Terminal
Terminal Block
(appearance
may vary)
Ground Plate
Conduit
Wire Tips
Conduit
Terminal Block
Loading ...
Loading ...