Loading ...
Loading ...
Loading ...
ge.com
COOLMODE
RemoteControl
l. Px_ss COOLpad.
2. Px_ss LOW.IVIEDor HIpads to set desired fire speed.
3. PI_SS the INCREASEA/DECREASEVpads to set the
desix_d tempenmu'e 60°F to 85°F in l °F increments.
ControlPanel
l. Pxess fl_e MODEpad until tile COOLindicator lig]lt is
lit and the LOW.MEDor Hlin(ficator light is lit fi)r
die (lesix_(1thn speed.
2. Pxess the INCREASEA/DECREASET pads to set the
desix_d temperature 60°F to 85°F in l °F increments.
A them/ostat is used to maint_fin tile room
temperature. Tile compressor will e_cle on and off
to kee I) tile room at tile set level of (omfi)rt. Set tile
thermostat at a lower number and file indoor _firwill
become coolex; Set tile thermostat at a higher nmnber
and tile indoor air will become _mnex:
NOTE:ff theairconditionerisoffandisthenturnedon
whilesettoCOOL,it willtakeapproximately3minutesfor
thecompressortostartandcoolingtobegin.
CoolingDescriptions
ForNormalCooling--Select tile COOLmode and
HIGHor MEDthn with a middle set temperature.
ForMaximum Cooling--Select tile COOLmode
and HIGHtim with a lower set temperatm>.
ForQuieter&NighttimeCooling--Selecttile COOLmode
and LOWthnwidl a middle set temperature.
NOTE:If youswitchfroma COOLsettingtoOFFor to
afansetting,waitatleast3minutesbeforeswitchingback
toaCOOLsetting.
Fan Switch
Tile thn switch is located behind tile ti'ont grille on the
control box. Access through a hole in control box.
_,_]mn set at CYCLE(do_n) tile thn e',cles on and ottl
When set at CONT(continuous, up) tile tim runs all tile
time providing a m(/x_ balanced mml)eraU/x_. The unit
is shipped in the CONrsetting.
FAN MODE
Use tile FANmode to provide _dr circulation and
filtering without cooling. Since fhn only settings (1(1not
provkle cooling, a temperature setting will not be
displa}ed.
RemoteControl
Px>ss FANpad. Press LOW.IVIEDor HI pads to set
(lesix_(1 fhn speed.
ControlPanel
Pxess die MODEpad until tile FANindicator light is lit
and tile LOW, IVIEDor HIin(ficator light is lit fi)r the
(lesix_(1 fan speed.
Vent Control
The vent control is located behind tile ti'ont grille on
tile right side of tile air (fischarge area. "_\lmn set at
CLOSE,only the air inside fl_eroom will be circulated
and conditioned. When set at OPEN,some inside air is
exhausted outside.
To opeIl or close tile vent:
1. Remove the ti'ont grille.
2. Remo\ e the vent card scx_.
3. Remove vent card, turn it over and replace it 17}
locating rear hole in card over locating pin inside air
discharge and reattaching scre_ at fi'ont.
Theunitleavesthefactoryset attheCLOSEposition.
._Locating hole
Screwhole "_.
OPENposition
(Meshendtowardback)
Screwho
CLOSEposition
(Meshendtowardfront)
A# Direction
Horizontal lomers
on fl_e Ii'ont grille let
you control tile air
(lirection up and
doPvI/.
Remove tile fi'ont
grille to a@/st the
vertical lou\'ers
side-to_ide to
dixect file air
left or fight.
Loading ...
Loading ...
Loading ...