Loading ...
Loading ...
Loading ...
WARNING
warning
USE AN AUTHORISED PERSON
As stated in the local municipal building codes and other relevant
statutory regulations.
• WiringconnectionsmustbeinaccordancewithAS/NZS
3000 Wiring Rules and any particular conditions of the
local authority.
• Refertodataplateforratinginformationandcircuitdiagram.
The data plate is positioned behind the bottom of the oven
door. The circuit diagram is positioned on the top panel of
the appliance.
• Anallpoledisconnectfunctionalswitchshouldbeprovided
near the appliance in an accessible position. Refer to AS/
NZS 3000 clause 4.3.11
• Wiringshouldbeprotectedagainstmechanicalfailure.
Refer to AS/NZS 3000 clause 3.9
• Ameansofdisconnectionwithacontactseparationofatleast
3mm must be supplied in the fixed wiring.
• Togainaccesstothemainsconnectionterminals,remove
the rear panel by unscrewing the 2 assembly screws.
NOTE: Where connection is made to a multi-phase 240V
supply, the bridge piece should be removed from between
the active connections.
WARNING
warning
IMPORTANT: This appliance must be properly earthed.
• Donotlifttheappliancebythedoorhandles.
• Preparethecupboardopeningtomatchyourappliance
measurements. (See diagrams).
• Slideapplianceintothecupboard,ensuringthatthesupply
cable (where fitted) does not kink.
• Topreventtipping,usethescrewssuppliedtosecureyour
oven into the cupboard. Use just 2 screws for single cavity
ovens and 4 screws for dual cavity. Remove the bottom
door in dual cavity ovens to provide access to the bottom
2 screwing points. (See illustration page 23).
• Forappliancesttedwithasupplyexiblecord,ifthecord
is damaged, it must be replaced by the manufacturer or its
service agent or similarly qualified person in order to avoid
a hazard. The plug must be accessible after installation.
• Wheretheapplianceisbuiltintoacabinet,thecabinet
material must be capable of withstanding 70°C. Installation
into low temperature tolerant cabinetry (e.g. vinyl coated)
may result in deterioration of the low temperature coating by
discolouring or bubbling.
• Iftheapplianceisinstalledadjacenttovinyl-wrappedsurfaces,
use an installation kit available from the vinyl-wrap supplier.
• ElectroluxHomeProductscannotacceptresponsibility
for damage caused by installation into low temperature
tolerant cabinets.
• Afterinstallation,testandensurethattheapplianceoperates
correctly before handing it over to the customer.
WARNING
warning
CAUTION: To avoid any potential hazard, you must follow our
instructions below when you install your appliance. Failure to
install the appliance correctly could invalidate any warranty
or liability claims and lead to prosecution.
installation installation
22 INSTALLATION Built-in Cooking Built-in Cooking INSTALLATION 23
Cabinet Construction for your appliance
For the best integration within a kitchen, install this appliance in
a standard 600mm wide cupboard that gives a flush fit with the
surrounding cupboard fronts (figure A).
A recess of 20 mm is ideal. It can also be installed using a proud
fit with the surrounding cupboard (figure B).
NOTE: Your appliance must be mounted on a flat surface for
the full width and depth of the product.
Underbench Ovens
Your underbench oven looks best when the control panel is directly
under the benchtop. An upper infill panel may have to be added
if the cooktop placed above the benchtop is too deep.
Refer to cooktop installation instructions for required clearance
between cooktop and oven.
Oven Dimensions
Figure A – Flush fit (top view) Figure B – Proud fit (top view)
Underbench Oven
595 x 595 x 567mm (HxWxD)
Separate Grill Underbench Oven
725 x 595 x 567mm (HxWxD)
Separate Grill Wall Oven
888 x 595 x 567mm (HxWxD)
Cleat
Figure A – Flush fit (top view)
Figure B – Proud fit (top view)
Cupboard
door
Cupboard
door
Infill panel
Cupboard front
20mm
100mm max
100mm max 100mm max
Cleat
Figure A – Flush fit (top view)
Figure B – Proud fit (top view)
Cupboard
door
Cupboard
door
Infill panel
Cupboard front
20mm
100mm max
100mm max 100mm max
NOTE: If a powerpoint is fitted it must be
accessible with the appliance installed.
Loading ...
Loading ...
Loading ...