Loading ...
Loading ...
Loading ...
Turning On and Turning Off the Cooktop Appliance
NOTE: Do not operate the cooktop without first placing a suitably sized cooking vessel on the appropriate cooking
zone. If the correct sized cooking vessel is not placed on the cooking zone, the Cooking Zone Select touch control
& Power LED display will indicate pan not detected. Settings can be changed, but the zone will not work until the
pot is replaced.
If the appliance is in Stand-By-Mode, it is put into Operating-Mode by pressing the On/Off Power touch control for
at least 1 second. A beep signal indicates the successful operation acoustically, with a small indicator above the
touch control being lit.
Each Cooking Zone Select touch control & Power LED display will display a ´0`. The decimal points on the Cooking
Zone Power Displays will flash until a cooking zone is selected.
If there is no operation within 20 seconds, all the Cooking Zone Select touch control & Power LED displays will
automatically turn off and the appliance will be re-set into Stand-By-Mode.
If the On/Off Power touch control is pressed for more than 1 second (in Operating-Mode), the appliance is
switched off and is set into the Stand-By-Mode again. The appliance can be turned off by pressing On/Off at
any time. The small indicator above the touch control will also turn off.
If there is any residual heat remaining in a cooking zone, this will be indicated in the corresponding Cooking
Zone Select touch control & Power LED display as a red “H”.
Note: All cooking zones have a pre-set limit on the length of time they will run without any setting changes
(table further in the manual).
Selecting A Cooking Zone
1. Select a single cooking zone by pressing the corresponding Cooking Zone Select touch control & Power LED
display (07, 08, 09 or 10), and the decimal point of the chosen cooking zone stays bright while the others turn
off.
2. For the selected cooking zone, you can set or adjust the power level between 1-9 by touching the Power/Timer
Slide touch control (05) All of the other cooking zone displays will have a visible ‘O’, value (if in use) or ‘H’ (if
recently used). The Power/Timer Slide touch control can be operated by either touching the sensor at some
point (lower values to the left), or placing a finger on the sensor and sliding it left and right. The position will be
displayed on the Power/Timer Slide LED Indicator above, as well as on the Cooking Zone Select touch control
& Power LED display.
If left idle for more than 10 seconds, the LED for the chosen cooking zone display will turn off (the cooking
zone is no longer selected). Press the Cooking Zone Select touch control & Power LED display again to select
the cooking zone again. Other cooking zones can be selected without waiting for the previous one to become
inactive.
The Cooking Zone Select touch control & Power LED display works on a thermostat system. This means that
the cooking zone will switch on and off in order to remain at the chosen Power Level. NOTE the cooking zone
will remain on for longer periods if a higher Power Level is chosen, alternatively the cooking zone will be on
less regularly on lower Power Level Settings.
Turning Off Individual Cooking Zones
A cooking zone can be turned off by selecting the specific cooking zone touching the Cooking Zone Select touch
control & Power LED display and then using the Power/Timer Slide touch control to set the power to 0.
The Boost Function
The Boost function is available at the front left and rear right cooking zones. It is used to speed up the initial heat up
time (say boil a pot of water) and only runs for a short time (5 minutes).
1. Select a cooking zone and press the Boost Power touch control (04) once, so the Cooking Zone Select touch
control & Power LED display changes from the current value to “P”. The power boost function is now active
(indicator above the sensor is lit). Once the 5 minutes has passed, the cooking zone power level will drop to 9.
Note: The Boost function uses significantly more power than the nominal power (see appliance details). If used
in conjunction with other cooking zones, the max power available on the other cooking zones may be reduced
to keep power usage within the total allowed.
2. To disable the Boost function, press the Cooking Zone Select touch control & Power LED display for the
cooking zone again (so the decimal point is on) and either press the Boost Power touch control (04) again (the
cooking zone power level reverts to 9) or adjust the power level with the Power/Timer Slide touch control (05).
The indicator above the Boost Power touch control will turn off (unless the second zone is using the boost
function).
4
Loading ...
Loading ...
Loading ...