Loading ...
Loading ...
Loading ...
31-2000654 Rev. 3
Installation
Instructions
WARMING DRAWER CUSTOM
PANEL ACCESSORY KIT
ZXW900
For installation of 30” wide warming
drawer custom panel and custom handle.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
ŶIMPORTANT – Save these instructions
for local in spec tor’s use.
ŶIMPORTANT – Observe all governing
codes and ordinances.
ŶNote to Installer – Be sure to leave these
instructions with the consumer.
ŶNote to Consumer – Keep these instructions for
future reference.
ŶSkill level – Installation of this custom panel kit
requires a qualified installer or service technician.
Ŷ3URSHULQVWDOODWLRQLVWKHUHVSRQVLELOLW\RIWKHLQVWDOOHU
Ŷ3URGXFWIDLOXUHGXHWRLPSURSHULQVWDOODWLRQLV127
covered under the warranty.
TOOL AND MATERIALS REQUIRED
Ŷ6DIHW\JODVVHV
ŶCut resistant gloves
Ŷ3KLOOLSVVFUHZGULYHU
Ŷ'ULOODQGDSSURSULDWHELWV%UDGSRLQWUHFRPPHQGHG
for drilling through wood panels)
Ŷ&XVWRPSDQHO
Ŷ&XVWRPKDQGOHRSWLRQDO
Ŷ$GKHVLYHUHFRPPHQGHGIRUPHWDOWRZRRG
Ŷ$GKHVLYHUHFRPPHQGHGIRUSODVWLFWRZRRG
PARTS SUPPLIED
Ŷ/DPS-HZHO
Ŷ0HWDOPRXQWLQJSDQHO
Ŷ%DJRIVL]HVFUHZV
This kit contains a mounting panel to support a trimless
custom drawer front up to 3/4” thick. The tubular
handle can be reinstalled onto the custom panel with
longer screws (not provided). Or, the original handle
can be replaced with a custom handle of your choice.
(Handle is not supplied.) Choose a custom handle to
match or complement cabinetry hardware.
IMPORTANT: The warming drawer should be
installed according to the installation instructions
packed with the product. The original drawer front will
be removed and replaced with a custom panel.
Ŷ&XWHGJHVRIWKHGUDZHUSDQHOZLOOEHVHHQDQG
must be finished for best appearance.
Ŷ7KHFXVWRPGUDZHUIURQWSDQHOERWKUDLVHGDQGIODW
design, should be constructed in the same manner
as typical cabinet doors.
Ŷ2UGHUWKHFXVWRPGUDZHUSDQHOIURPWKHFDELQHW
manufacturer. Be sure to provide the exact
dimensions so that the panel is constructed
accurately.
Ŷ2UGHUWKHRSWLRQDOFXVWRPKDQGOHWRFRPSOHPHQWRU
match surrounding cabinetry handles.
1
PREPARE DRAWER FOR PANEL
INSTALLATION
Ŷ2SHQWKHGUDZHUIXOO\
Ŷ7XUQWKHZDUPLQJGUDZHURII
2
REMOVE ORIGINAL DRAWER
FRONT
Ŷ5HPRYHVHYHQVFUHZV5HPRYHIRXUIURPWRS
inside and three from bottom. Set these screws
aside – they are no longer needed.
Ŷ6XSSRUWWKHGUDZHUIURQWDV\RXUHPRYHVFUHZVWR
prevent the possibility of falling.
3
PREPARE CUSTOM PANEL
Ŷ7KHFXVWRPSDQHOVL]HLVGHWHUPLQHGE\WKH
cabinetry dimensions and spacings.
Ŷ2QFHWKHFXVWRPSDQHOVL]HLVGHWHUPLQHGSODFH
the metal panel on the custom panel and check the
squareness and correct placement of the metal panel,
and mark the hole for the indicator light. Confirm that
the hole marking provides the indicator light to the
right side of the custom panel appearance side.
Ŷ'ULOOD´KROH$%UDGSRLQWGULOOELWLVUHFRPPHQGHG
Loading ...
Loading ...
Loading ...