Loading ...
Loading ...
Loading ...
3.1 GUARANTEE
Draper tools have been carefully tested and inspected before shipment and are guaranteed to be
free from defective materials and workmanship.
Should the tool develop a fault, please return the complete tool to your nearest distributor or
contact:
Draper Tools Limited, Chandler's Ford, Eastleigh, Hampshire, SO53 1YF. England.
Telephone Sales Desk: (023) 8049 4333 or:
Product Helpline (023) 8049 4344.
A proof of purchase must be provided.
If upon inspection it is found that the fault occurring is due to defective materials or workmanship,
repairs will be carried out free of charge. This guarantee period covering parts/labour is 12 months
from the date of purchase except where tools are hired out when the guarantee period is 90 days
from the date of purchase. The guarantee is extended to 24 months for parts only. This guarantee
does not apply to normal wear and tear, nor does it cover any damage caused by misuse, careless
or unsafe handling, alterations, accidents, or repairs attempted or made by any personnel other
than the authorised Draper warranty repair agent.
Note: If the tool is found not to be within the terms of warranty, repairs and carriage charges will be
quoted and made accordingly.
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its
terms are not authorised.
Your Draper guarantee is not effective unless you can produce upon request a dated receipt or
invoice to verify your proof of purchase within the guarantee period.
Please note that this guarantee is an additional benefit and does not affect your statutory rights.
Draper Tools Limited.
(12)
(13)
(14)
– At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is
disposed of according to national regulations.
– Contact your local authority for details of collection schemes in your area.
In all circumstances:
Do not dispose of power tools with domestic waste.
Do not incinerate.
Do not abandon in the environment.
Do not dispose of WEEE* as unsorted municipal waste.
* Waste Electrical & Electronic Equipment.
3. GUARANTEE
- 4 -
(1)
(2)
(3)
(4)
(6)
(7)
(8)
(9)
(10)
(11)
(5)
(3)
(6)
(11)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(5)
(12)
(13)
(14)
Slide the battery compartment cover (5) up slightly
before lowering it down to remove it. Insert the 3 x AA
batteries, taking note of the polarity indicated inside the
compartment. Replace the cover securely.
Ensure the laser beam aperture is covered to
avoid accidental beam exposure during battery
installation/replacement.
Remove the tripod from the case, extend all the legs and place the tripod into position.
Ensure the locking screw on the side of the tripod is tight. Adjust the height of each leg individually
to align the bubble on the top of the tripod as near as possible to the centre of the circle.
Remove the rotary base and screw onto the tripod taking care not to disturb its position. Using the
three adjusters, align the bubble on the rotary base as near to the centre of the circle as possible
then align the bubble on the self-levelling laser level as near to centre of both vials.
To fine tune the rotary base, place the level centrally into the clamp and tighten. Rotate the level
clockwise until it is directly over one of the three adjusters. Turn the adjuster until the horizontal
vial is level. Rotate the level a further 120° clockwise and adjust it to horizontal. Rotate the level a
further 120° to complete the final adjustment.
If the location of the height of the tripod is changed these adjustments must be repeated.
Loosen the transportation lock (11) prior to use.
Select the vertical line with button (3) or the horizontal
line with button (6) or both for a cross.
Wearing the goggles supplied will enhance the
laser beam. The beam will remain level providing the
error margin does not exceed 6°(+/-).
Do not dispose of WEEE*
unsorted municipal waste.
Loading ...
Loading ...
Loading ...